Jump to content

What's Happening?

BG46

Recommended Posts

BG46 Enthusiast

BG46

Posted
Posted

for the past few months i'm having to add coolant to my resevior as my "low coolant light" has been coming on.

i had a local garage do a pressure test and they found no leaks.

this past week i've noticed when i start the truck after sitting for a while there is a rather larger puff of white smoke coming out of the exhaust. it seems to have a faint aroma of coolant (don't know if that is true or my mind playing tricks).

can the coolant be leaking into the engine and cause this problem or is there some other explanation?

it's a 2003 GMC yukon xl if that helps.

thanks

jacko207 New Member

jacko207

Posted
Posted

Could also be head gaskets or a bad cylinder head. Coolant can leak into the cylinders after the engine is shut off and then gets pushed out the exhaust on start up. I've had the same problem with an 04 Silverado.

There's a service bulletin for heads with a bad casting.

 

 

Subject: Information on Gradual Coolant Loss Over Time with No Evidence of Leak Found #06-06-01-019B - (06/12/2007)

 

 

 

Models: 2004-2006 Buick Rainier

 

2001-2006 Cadillac Escalade Models

 

2001-2006 Chevrolet Avalanche, Blazer, Silverado, Suburban, Tahoe, TrailBlazer Models

 

2001-2006 GMC Envoy, Jimmy, Sierra, Yukon Models

 

2001-2004 Oldsmobile Bravada

 

2005-2006 Saab 9-7X

 

with 4.8L or 5.3L VORTEC® GEN III, GEN IV V8 Engine (VINs V, T, M, B, Z -- RPOs LR4, LM7, LH6, L33, L59)

 

 

 

 

--------------------------------------------------------------------------------

 

This bulletin is being revised to include engine RPO L59. Please discard Corporate Bulletin Number 06-06-01-019A (Section 06 - Engine/Propulsion System).

 

 

--------------------------------------------------------------------------------

 

Some vehicles may experience a gradual coolant loss over time. A very low percentage of cylinder head(s) manufactured with an embossed Castech logo may develop a porosity crack in a very specific area.

 

Inspect the cylinder head assembly to determine if the casting was manufactured by Castech. This can be accomplished by inspecting for their casting logo located on top of the intake port, under the rocker arm support rail and in the spring deck cavity portion of the cylinder head.

 

Important: If the cylinder head(s) are Not a Castech casting, follow normal diagnostic procedures in SI to determine the cause of the coolant loss.

 

Refer to the following illustrations on how to identify Castech casting and/or the very specific areas of the cylinder head(s) for a coolant leak from porosity.

 

 

 

 

 

Cylinder head(s) location of the Castech manufacturing casting logo (1).

 

 

 

 

 

Close up view of the cylinder head(s) showing the Castech manufacturing casting logo (1).

 

 

 

 

 

If the cylinder head(s) is a Castech casting (1), inspect the area around the five oil drain holes for witness marks indicating coolant seepage over time (2).

 

Important: If No evidence of coolant loss is found on inspection of Castech casting cylinder head(s), follow normal diagnostic procedures in SI to determine the cause of the coolant loss.

 

 

 

 

 

The crack location can be found in any of the five cylinder head(s) oil drains. This can be seen as a clean or shiny area, on an otherwise stained surface (1). Pressurizing the cooling system at this time may reveal coolant, air, or a combination, weeping in the described area. If inspection reveals evidence of coolant witness marks (1), replace the entire cylinder head(s) assembly.

98 Z71 SLT Senior Enthusiast

98 Z71 SLT

Posted
Posted
Could be intake manifold gasket. I know the older ones had problems but I thought the newer ones did not.

 

CANNOT be his intake manifold gasket. These newer engines have a "dry" intake...meaning there is NO coolant running through them.

 

If you have absolutely NO SIGNS of external coolant loss, you have cylinder heads with hairline cracks in them.

 

Stop off at your GM dealer, talk to the engine tech. Add some GM coolant dye to your recovery bottle. Drive it for a week or two, pull off both valve covers. Then, take a flourescent light and shine the light on the exposed head surfaces. That will tell if you have hairline cracks in the cylinder heads.

marko Enthusiast

marko

Posted
Posted
for the past few months i'm having to add coolant to my resevior as my "low coolant light" has been coming on.

i had a local garage do a pressure test and they found no leaks.

this past week i've noticed when i start the truck after sitting for a while there is a rather larger puff of white smoke coming out of the exhaust. it seems to have a faint aroma of coolant (don't know if that is true or my mind playing tricks).

can the coolant be leaking into the engine and cause this problem or is there some other explanation?

it's a 2003 GMC yukon xl if that helps.

thanks

 

It's either a headgasket issue or a cracked head. Unfortunately :sick:

jnbkosmo Enthusiast

jnbkosmo

Posted
Posted

On my 03 Avalanche w/ the 5.3 my water pump was leaking while running and dripping onto the exhaust.My service rep said that it would boil off and that was why I would never see any drips.No problems after the water pump was replaced.

  • 2 weeks later...
BG46 Enthusiast

BG46

Posted
  • Author
Posted
On my 03 Avalanche w/ the 5.3 my water pump was leaking while running and dripping onto the exhaust.My service rep said that it would boil off and that was why I would never see any drips.No problems after the water pump was replaced.

 

 

 

thanks for all the replies.

guess i better get it into the dealer and checked out before something more serious happens.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • asilverblazer
      Slate Electric Truck

      By asilverblazer · Posted

      I like the idea.  I would pick diesel if I had a choice. I need pictures though.
    • newdude
      Help purchasing a touch screen digitizer

      By newdude · Posted

      I've installed cheap eBay new aftermarket digitizers before.  They work.  Did a bunch of Cadillac CUE (aka Cadillac's MyLink) for someone years ago.  They all worked fine after the repair.    That number 22740886, that is a component part # for GM.  You can use it to search, but its not something that's obtainable at the dealer level.     So pretty much any of these will work - 2015 Colorado Digitizer for sale | eBay
    • asilverblazer
      give me some tips to make my truck look better

      By asilverblazer · Posted

      Black bumper and the later years Z-71 style color matched grille.
    • fondupot
      Exhaust heat while towing!

      By fondupot · Posted

      You can install tailpipes that direct the exhaust sideways vs the OEM one that goes straight back. There are several on the market, do you own research. HOWEVER, you need to make sure the Venturi vents are still intact, otherwise it will throw a engine code. There is a sensor somewhere that detects back pressure on the exhaust. And if it doesn't collect the correct metrics, it will throw the truck into limp mode. 
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      "Teardown" is complete. Head surfaces are clean and ready, new intake is prepped and ready. Coolant drained and water pump is removed, radiator is removed, new hoses and pump are ready.   The replacement intake is also from a '95 (with I think 260k, the odometer said). Noticeably less pitting where it covers the rear coolant passages. I'm not sure if that's a tribute to more frequent use, more frequent coolant changes/upkeep, or if the intake was machined at some point. But it appears I found a good one.   My coolant hoses were original, and the lower hose still retained the factory spring inside. It's not really rusty, but it's got deposits all over it. Unsure if I should re-install it (will thoroughly clean it first). Someone said hose technology has gotten better since 1995 (has it?) and I don't need the spring. I think modern EPDM is what made those hoses last from 1995-2026, so it's a question of how much suction can the water pump really pull, and will it collapse the hose without a spring?   I'm stopped and waiting for parts, however.   When I first brought the truck home, the fan was intermittently hitting the radiator shroud. I could see someone had monkeyed with the shroud (put a bunch of cardboard as a spacer between the upper/lower shroud halves. Someone said the motor mounts have likely failed and the engine has sagged. I wasn't sure I believed that. The engine is really solid in its mounts: To remove the old intake I *just* nearly permanently welded to the heads with freshly cured RTV and gasket snot two weeks ago, I literally had to use the arms on my lift and a chain with a bolt attached to the intake to pull it loose. It almost picked the front of the truck off the ground before ....scuuuuuuuuuuup.... I could actually hear the gaskets tearing and it broke loose and the whole truck settled back down. Motor barely moved.   SO, those parts I'm waiting on... The lower radiator mounts/bushings had completely failed. The radiator needs to be insulated from the rad support, and the bushings help the rad stand at the correct height. The plastic "baffle" was also destroyed at some point. Someone had attached the shroud to it incorrectly, overlapping a joint that should have been underlapped, creating another suspect issue potentially causing things to hit the fan. Broken tabs, side is busted off, and it's perma-formed/bent where it was jimmied incorrectly.   The baffle? Unobtainum. Long since discontinued from GM, of course. Aftermarket/capa/chinese? Also unobtanium. In GM's infinite wisdom, it appears there are at least two different variations whether the Blazer is 2 or 4 door, and I can't yet tell if they shared the same part with the S-pickups. Plan B, if I can't find a viable used one, will be to create a bracket to re-assemble the critical joint I need to seal a gap with the shroud. But that will bug me, it won't be...perfect.   The water pump bolts appear to have been installed with...plumber's putty. I guess, sure, if it works...? I've found a few "backyard fixes" like that. Someone's been here before....   If I can't find someone to jam bamboo under my fingernails to fill my free time this week I think I'll install the driver's power window motor and replace the rear door speaker that's inop. I've got a genuine GM "9.5" ohm working replacement. Why GM used a non-standard resistance....nevermind. Of course they did, you can get more sound from a cheap factory amp that way.   And the saga goes on...

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...