Jump to content

Installing Ipod Cable In Center Console - 2008 Sierra Denali

TulsaHogFan

Recommended Posts

TulsaHogFan New Member

TulsaHogFan

Posted
Posted

Is there any easy way to do this without drilling a hole to run it through? Anyone have any tips on how to get the cable in the center console without doing too much damage?

TulsaHogFan New Member

TulsaHogFan

Posted
  • Author
Posted

I am using the Kenwood IP 201 i believe. I am asking more about getting through the floor of the center console, if there is an easy way to do it, or any ideas. I have the Ipod adapter working but its in my glove box and i don't want to have to reach over there when i want to change something.

 

I would rather have it in my console under my arm for when i want to grab it.

Julian@MotoCARR Enthusiast

Julian@MotoCARR

Posted
Posted

You will probably have to drill a hole for the cable to actually make it into the center console. I know that's not the most favorite thing to hear, but the hole would only have to be about the size of a Nickel, and you can make the hole on the inside, side wall of the console so that way when you look inside it. it's not as noticeable, and you aren't likely to have stuff fall in the hole. You will have to uninstall the cable from behind the radio because that end is smaller than the end that plugs into the actual ipod. Snaking the wire up to the radio isn't all that hard at all!

SparkySparks Enthusiast

SparkySparks

Posted
Posted

You can always buy a rubber plug like you would use if you ran a wire thru the firewall, just cut it so it goes around the cable and it will help hide the hole you drilled to run the cable. I think the only option to get the cable in the console with out drilling is if you removed the power plug and replaced it with the wire for the Ipod.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,979
    Total Members
    8,960
    Most Online
    rayredbone
    Newest Member
    rayredbone
    Joined

  • Who's Online   1 Member, 0 Anonymous, 515 Guests (See full list)

  • Latest Articles

  • Posts

    • Grumpy Bear
      AFM Experience

      By Grumpy Bear · Posted

      Question @diyer2 on this line if you please. Are you saying the shudder is the system turning on and off at the frequency of the shudder? Guess I'm asking if you are saying you have seen it do this with the bi-direction scan tool in graph mode? If so have you been able to discern the 'trigger'. Something is telling to cycle rapidly.    My truck just started doing this recently. 197K on the clock. My response has been M5 anything under 55 mph. I treat it like a lugging stick shift. Gear down and let it spin a bit. Engauge M5, then tow mode and then M6 lets the trans stay in 5th but the AFM is active. Smooth like Skippy.    My thought was that as a machine ages the friction gets lower and as the system is load based, the lower friction would allow it to turn on at ever lower rpm until it reaches the lugging point. And yes I am ignorant of any minimum rpm requirement for the system. If you know that would be useful information.    As you know I run a Scan-Gauge II which allows me to watch the On/Off of the signal to the VLOM. While in the shudder mode I'm not seeing is cycle at that frequency or at all for that matter outside the triggers @newdude posted a few years back. Now is it possible that the refresh rate isn't fast enough to catch it? Maybe. It is why I asked my first question about graphing and trigging parameter.     As we have observed from members here the failure point is all over the map miles wise as you note yourself in your opening post. That by itself begs a few questions like fellows that comment on these lifters failing even after the system has been disabled. Long after. 😬   https://www.enginelabs.com/news/tech-tips-replacing-ls-active-fuel-management-lifters-with-melling/   The Gen5 lifters operate the same as the LS versions. In fact they are the same lifter.    https://www.enginelabs.com/tech-stories/sorting-out-gen-v-lt-lifter-failure-with-a-simple-valvetrain-fix/        
    • SwitchBladeSierra
      14-18 Sierra 1500 Heated Steering Wheel Help

      By SwitchBladeSierra · Posted

      UPDATE 2: Steering wheel control backlights and control of the cluster can supposedly be achieved by adding a wire to pin 20 of the cluster and tapping it to pin 2 of the main clock spring harness. I'm going to give it a shot - will update  
    • newdude
      Seems to be Missing a lot of Updates

      By newdude · Posted

      GM Global A pickups 2019-2022 can do OTA programming for the radio.  GM VIP (GM Global B) can do OTAs for almost every module on board.  So a 2022.5 and newer pickup can do OTAs for recalls like the 2.7 fuel flow recall.  EVs get OTAs that improve one pedal driving, radio issues, HVAC issues, updated battery management software, etc.     So age of the vehicle/what GM electrical platform its on will alter what amount of updates can be pushed on OTAs.  
    • Blade8971
      Upgrade to a 2026 AT4 with the 3.0L Duramax

      By Blade8971 · Posted

      Thank You.   So far my new ride is making me look like a genius for going with the 3.0L, as my first fuel refill occurred over three weeks from when I took delivery.  This engine combination is very amazing.  So far no issues and had not done a regen yet.
    • Chuck FB
      Correct way to service 2024 l8t allison trans?

      By Chuck FB · Posted

      I am curious as to how much fluid you put back in the transmission ( assuming you had replaced the filter to compare to my findings ) and then went through the process of warming up the trans before pulling the check plug to drain out the excess and if you measured how much came back out.    I just found it surprising that some claimed a certain amount less fluid being put in and then draining some back out. The attitude of the truck as per if the surface is level and how the trucks stance is would make quite a difference since the check plug is right at the front of the transmission. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...