Jump to content

Where is your catch can mounted?

By 02suburbanZ71
April 24, 2015 in Gen III & Gen IV V8 Engines (LS-Based)

Recommended Posts

Senior Enthusiast

02suburbanZ71

Posted April 24, 2015

Posted April 24, 2015

I want a catch can and i kind of like the looks of the jegs can with breather. Can i see some pics of your installs

Senior Enthusiast

Chris

Posted April 24, 2015

Posted April 24, 2015

Side of the alternator bracket on the Gen 3 trucks

Senior Enthusiast

02suburbanZ71

Posted April 24, 2015

Author

Posted April 24, 2015

Mine does not have that bracket on the alt

Senior Enthusiast

Chris

Posted April 24, 2015

Posted April 24, 2015

First off that pic is of a gen 4 LS.

Senior Enthusiast

02suburbanZ71

Posted April 25, 2015

Author

Posted April 25, 2015

First off that pic is of a gen 4 LS.

Cool thanks chris

1 month later...

Senior Enthusiast

BigBlueLB756

Posted June 6, 2015

Posted June 6, 2015

Just for fun, I thought I would run a little "RX Catch Can Test" of my own to see how much gunk my first "Cheap-*ss" catch can was letting get past with a second one in series. Either place is good, but the front mount is better for ease of emptying.

1 month later...

Enthusiast

BretD04GMC

Posted July 30, 2015

Posted July 30, 2015

I run one of these on my '04. Have it mounted to the front of the passenger side cylinder head:
http://www.ebay.com/itm/99-07-SILVERADO-SIERRA-TAHOE-4-8-5-3-6-0-LS-BILLET-OIL-CATCH-CAN-SEPARATOR-TANK-/110927987832?hash=item19d3d2c478

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

Recently Browsing 0 members
- No registered users viewing this page.
Forum Statistics

250.3k
Total Topics

2.7m
Total Posts
Member Statistics

342,714
Total Members

8,960
Most Online

Newest Member
Peoplemvr
Joined 33 minutes ago
Who's Online 8 Members, 0 Anonymous, 798 Guests (See full list)
- Nightmare_snake
- Peoplemvr
- mikeyk101
- revmanii
- KARNUT
- DarkSkyX31
- Jus Cruisin
- markw8

Latest Articles
Posts
- GMC 1500 Illuminated Front Grill Emblem REPLACEMENT.
  
  By Peoplemvr · Posted 2 minutes ago
  
  Hi there. Long time lurker, first post. i have read the previous posts regarding the water ingress problem with this emblem. I bought my 1500 the summer of 2025 new and after reading the MANY problems with these emblems failing I decided to install one anyways. As per a YouTube video, I sealed ( or tried to) this sign with silicone sealant around the outer perimeter joint and the holes that were already somewhat sealed on the rear plate of the emblem. And installed the connector assembly using dielectric grease on the connectors. The installation looked great and worked well for about 4 months……then FAILURE. Grrrrrr…… I live in the great white north and wash my truck weekly in an automatic car wash to keep the salt off. Let me tell you that removing the old, failed emblem is a whole different animal than removing the OEM individual letters without removing the grill assembly. Mainly because the illuminated logo is built differently than the original letters which you can remove the red surface lettering with a knife or some kind of blade which gives access to the tabs which hold the logo onto the grill. So I essentially destroyed the emblem to remove it. Doing so killed my chance of doing somekind of autopsy on the failed , old logo. But there was plenty of water inside when I ripped it apart. Prior to installing the new assembly I tried with the old harness and it works fine. I intend to seal the new logo with slow curing epoxy this time around. I think this newer emblem my be updated unit which I hope GM got the vendor to fix If this one fails I just going to revert back to the non-illuminated letters….AFTER PULLING THE GRILL. Any thoughts on sealing with epoxy would be appreciated. Thx! Doug
- Looking at ordering a '26 WT because I want a std cab, std bed
  
  By revmanii · Posted 1 hour ago
  
  PS: Here's pic of the 2014 wheels I'd like to run when it's not winter. Stuck my finger around new wheel caliper setup. Very little clearance. I suspect these won't fit, but won't know for sure till I try. Edit: And my first mod. Stubby antenna from the old truck.
- Looking at ordering a '26 WT because I want a std cab, std bed
  
  By revmanii · Posted 1 hour ago
  
  I bought it today and brought it home. They still owe me the bed liner, remote start, and they also agreed to get me the flat black bumpers to replace the optional chromes ones. While some folks may think I'm crazy, I think they'll look a lot better with all the other black stuff. Blacked out grill, mirrors, running boards, dark essentials Chevy tailgate lettering along with the black Silverado and Turbomax emblems. I do want replace dark essentials Chevy front grill emblem with the base level gold one. The 2.7 4 seems to run well and push a 1500 along just fine :).
- Gas Prices
  
  By Grumpy Bear · Posted 1 hour ago
  
  One of the most useful post I've seen. Thank you.
- Gas Prices
  
  By Atlas · Posted 2 hours ago
  
  Conversations with a hickory stump be like:
GM-Trucks.com Clubs
- Black Truck Club
  
  Open Club · 612 members
- White Truck Club
  
  Open Club · 380 members
- Canadian Owners Club
  
  Open Club · 282 members
- Red Truck Club
  
  Open Club · 156 members
- diesel 3.0
  
  Open Club · 279 members
- Texas Owner's Group
  
  Open Club · 371 members
- NorthSky Blue Club
  
  Open Club · 118 members
- Midwest Owner's Group
  
  Open Club · 212 members
- 2015 Custom Sport Club
  
  Open Club · 5 members
- GM Snow Plowing Club HD
  
  Closed Club · 14 members
Popular Contributors
- Week
- Month
- Year
- All Time
1. 1
  
  KARNUT
  19
2. 2
  
  Grumpy Bear
  17
3. 3
  
  Chuck FB
  11
4. 4
  
  Atlas
  9
5. 5
  
  Black02Silverado
  8
Show More

×

Forums
Main Site
Newsroom
Road Tests
Clubs
Gallery
Activity
- Back
- All Activity
- Search
Tools
More
- Back
- Guidelines
- Staff
- Leaderboard
- Online Users

×

Create New...