Jump to content

New Order Event Codes


Recommended Posts

Posted

I remember seeing in someones thread a list of the event codes...My new truck is at 4800 right now. Can someone please post the list of the event codes?

 

Thank You!!!!

 

ScottyC

Posted

Found it...

 

Here's a partial list of event codes.

 

• 500, this is a dealer stock order code used to order common vehicles. Please contact your dealer to receive an actual active order number.
• 1100, Preliminary order accepted (This means your dealer has entered your order into their system but does not mean they have the allocation to submit the order to GM yet. Speak with your dealer to verify when they expect to be able to submit your order for production)
• 2000, Order accepted by GM (This means the order has been submitted and accepted by production. You are now on your way.)
• 2030, Order re-edited (if necessary) (This is simply an edit code showing that something on your order has been changed. It does not mean your order has been accepted to production and really does not mean anything beyond your previous status other than a change has been made.)
• 2051, Order changed thru Web (same as above)
• 2500, Order preferenced (This means that the Order has been moved to the stage that parts department is now ready to place the orders for the components that will become your car)
• 3000, Order accepted by production control (This is the response from production to your 2500 status and is when Parts are actually ordered. No further changes can be made to your order once you reach this point.)
• 3100, Order available to sequence (This is more or less an inter-office memo from Parts to Production saying all parts are committed to this build, they are clear to sequence them for the build.)
• 3300, Order scheduled for production (This is the response to the 3100 status where Production is cleared to sequence and schedule the build) TPW usually avaiable
• 3400, Order broadcast (This is when the order is actually loaded onto the production line computers and parts are being staged for the build)
• 3800, Order produced (The vehicle is completed and has rolled off the line. A Vin is now available.)
• 4000, Available to ship (Vehicle is off the line and available to ship)
• 4104, Bailment Invoice (Shipping documents generated)
• 4200, Shipped (Vehicle has been moved by a carrier to another location or destination. If in combination with a 4300 status code then this is transfer to either a vendor for upfitting or to a distribution yard for final transportation.)
• 4300, Intermediate Delivery (In combination with a 4200 this is saying that the vehicle has been transported to a vendor or to a distribution center.)
• 4B00, Bayed (listed anytime a vehicle is sitting parked waiting for next mode of transportation. It can also be this status while in Quality Control)
• 4800 Rail Ramp Unload, end of the line by (if) rail. To be delivered by truck to dealer
• 5000, Delivered to the dealer
• 6000, Delivered to the customer
• 9000, Order Cancelled

Archived

This topic is now archived and is closed to further replies.

  • Latest Articles

  • Posts

    • You can install tailpipes that direct the exhaust sideways vs the OEM one that goes straight back. There are several on the market, do you own research. HOWEVER, you need to make sure the Venturi vents are still intact, otherwise it will throw a engine code. There is a sensor somewhere that detects back pressure on the exhaust. And if it doesn't collect the correct metrics, it will throw the truck into limp mode. 
    • "Teardown" is complete. Head surfaces are clean and ready, new intake is prepped and ready. Coolant drained and water pump is removed, radiator is removed, new hoses and pump are ready.   The replacement intake is also from a '95 (with I think 260k, the odometer said). Noticeably less pitting where it covers the rear coolant passages. I'm not sure if that's a tribute to more frequent use, more frequent coolant changes/upkeep, or if the intake was machined at some point. But it appears I found a good one.   My coolant hoses were original, and the lower hose still retained the factory spring inside. It's not really rusty, but it's got deposits all over it. Unsure if I should re-install it (will thoroughly clean it first). Someone said hose technology has gotten better since 1995 (has it?) and I don't need the spring. I think modern EPDM is what made those hoses last from 1995-2026, so it's a question of how much suction can the water pump really pull, and will it collapse the hose without a spring?   I'm stopped and waiting for parts, however.   When I first brought the truck home, the fan was intermittently hitting the radiator shroud. I could see someone had monkeyed with the shroud (put a bunch of cardboard as a spacer between the upper/lower shroud halves. Someone said the motor mounts have likely failed and the engine has sagged. I wasn't sure I believed that. The engine is really solid in its mounts: To remove the old intake I *just* nearly permanently welded to the heads with freshly cured RTV and gasket snot two weeks ago, I literally had to use the arms on my lift and a chain with a bolt attached to the intake to pull it loose. It almost picked the front of the truck off the ground before ....scuuuuuuuuuuup.... I could actually hear the gaskets tearing and it broke loose and the whole truck settled back down. Motor barely moved.   SO, those parts I'm waiting on... The lower radiator mounts/bushings had completely failed. The radiator needs to be insulated from the rad support, and the bushings help the rad stand at the correct height. The plastic "baffle" was also destroyed at some point. Someone had attached the shroud to it incorrectly, overlapping a joint that should have been underlapped, creating another suspect issue potentially causing things to hit the fan. Broken tabs, side is busted off, and it's perma-formed/bent where it was jimmied incorrectly.   The baffle? Unobtainum. Long since discontinued from GM, of course. Aftermarket/capa/chinese? Also unobtanium. In GM's infinite wisdom, it appears there are at least two different variations whether the Blazer is 2 or 4 door, and I can't yet tell if they shared the same part with the S-pickups. Plan B, if I can't find a viable used one, will be to create a bracket to re-assemble the critical joint I need to seal a gap with the shroud. But that will bug me, it won't be...perfect.   The water pump bolts appear to have been installed with...plumber's putty. I guess, sure, if it works...? I've found a few "backyard fixes" like that. Someone's been here before....   If I can't find someone to jam bamboo under my fingernails to fill my free time this week I think I'll install the driver's power window motor and replace the rear door speaker that's inop. I've got a genuine GM "9.5" ohm working replacement. Why GM used a non-standard resistance....nevermind. Of course they did, you can get more sound from a cheap factory amp that way.   And the saga goes on...
    • // Thank you, also for your  response. More information is always good. This 2013 GMC is most likely my 'forever truck"-I'm 77 and retired...and truck only has 42K on it-very clean-so I try to keep it that way.  Tks again for your  response- glenn
    • I started my install this weekend. Everything was pretty straight forward but I ran into one issue with running power through the firewall. The nipple grommet on my High Country already has a small harness running through it - has anyone else ran into this issue? And on the engine bay side, does the wire basically just penetrate the factory wiring boot? I did this on my '22 Trail Boss and it seems much easier but thats been a few years. My other thought would be possibly drilling a new hole adding a rubber grommet just to the lower left of the factory hole. Thoughts?   Has anyone used a T-harness off the Bose amp and obtained power from there? It seems a little odd that such a small amp needs 3 power leads
    • ///// Ok--Thanks for that info--I could not find yesterday when I looked for the specs on that NAPA filter what I wanted. Their website is not very user friendly. I buy all teh filters for  our three vehicles once or twice a year. Have always run NAPA Gold on everything I own....I buy it thru my Son's account for his business-which he has a Heavy Equipment repair shop-one reason he uses NAPA so much-they have such a full line of coverage for just about anything/anywhere- He gets s  good discount because of volume bought. Anyway-Thank you -Sir for your response.   glenn
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...