Jump to content

Exhaust question/help

psanders7983

Recommended Posts

psanders7983 Enthusiast

psanders7983

Posted
Posted

Posted this over the weekend, but thought I might get more input in this area. Just trying to decide what to do about the drone from my borla exhaust. I have found that kicking into 5th gear instead of 6th seems to quiet it down a lot when going 60-70 without killing the mpg. Again any thoughts are greatly appreciated.



I had a Borla Pro XS installed on my 2011 this week, the sound is nice and throaty with a lot of bass. 90% of the time I am loving it, but on the highway it's pretty loud especially around 70 mph. Gets better around 75. Just wondered if anyone had any low cost solutions. Not sure if resonated tips help or if I live with it until I decide I like it enough to keep or replace again with something less aggressive. Just wondered if anyone had any input for me. I'll try to get some video/audio posted in the next week or so. Overall great sound.. just 65-70 problematic drone.



thanks for any input.



mymaggiebell Enthusiast

mymaggiebell

Posted
Posted

i have a full borla exhaust and the ONLY drop i have heard was kind of between gears where it should have maybe stayed at a gear instead of shifting as you described. this is a very rare occurrence though, it honestly almost find it too quiet. sorry i wasn't much help

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,889
    Total Members
    8,960
    Most Online
    smandy
    Newest Member
    smandy
    Joined

  • Who's Online   4 Members, 0 Anonymous, 514 Guests (See full list)

  • Latest Articles

  • Posts

    • Jsdirt
      07 yukon xl 6.2 stalls at hot idle and wont restart

      By Jsdirt · Posted

      Holy s**t - not much of a parts thrower you say? You BLASTED that thing with the parts cannon!  You'd have been probably $1,000 ahead if you had just brought it to a competent shop rather than shotgunning a bunch of parts it clearly didn't need.   Just FYI - oil additives are really, REALLY good at ONE thing ... and that's emptying your wallet. They're ALL useless gimmicks.   If that has the L94 or L99, then #7 is an AFM cylinder. I'd suspect a failed lifter in that case.   If you leaned on wiring, sensors, and/or connectors while changing the oil, you'll have to check all that to be sure pins didn't get pulled out, connectors broken, etc.. Old wire loom that was barely adequate when new is certainly brittle by year 19 - make sure wires aren't chaffed and shorting out somewhere where you might have leaned. or supported yourself on it.   If your a mechanic, why didn't you just find out what you were missing and troubleshoot from there??  TIMED spark, fuel PSI / injector pulse, air, compression.  Can't make ANY money going the parts cannon route.
    • Jsdirt
      2027 GMC Sierra: Official Discussion

      By Jsdirt · Posted

      LOL! Are you joking?? That wax SUCKS! 100% gimmick made to "look" good.    After just TWO winters I had severe surface rusting in patches over 90% of the frame. Only reason it looks great in the pics is because I SATURATED the frame every single fall with used motor oil for 14 of the 16 years I owned it. Otherwise it would've been sent to the crusher 8 years earlier with the speed it was rusting prior!    I sold that POS 3 years ago. Was a gigantic headache the second it rolled off the showroom floor. Brakes pulsated on the TEST DRIVE. Door trim fell off the 1st week! Interior squeaked and rattled, and the drivetrain clunked after 2k miles. 4x4 switch failed shortly after. Front end - ball joints, struts, hub bearings - all failed between 38k-50k. Engine started burning oil at 50k. Rear and and transmission failed before 100k. Nothing but problems, and frustration with the piss-poor engineering designed to make you give up. Well, it worked! Nothing on that truck was easy to remove ... except the wheels. They haven't figured out how to screw that up yet. Give 'em time ...   I won't make that mistake again. EVER.   Such fond memories ... https://postimg.cc/K1qf23tS  https://postimg.cc/gallery/X02z64J  https://postimg.cc/gallery/mHSRXZv  https://postimg.cc/gallery/D4mMRfL
    • davester
      OBD not ready?

      By davester · Posted

      Different monitors do their test only under conditions specific to that monitor.  you MIGHT find the drive cycle conditions for the monitor that isn't ready on this site: https://lemon-manuals.la/   If it's not there, then it should be on alldata.com for your truck, but it requires a paid subscription.   And you need to know which specific monitor isn't ready.
    • RW2018GMC
      Me too……..

      By RW2018GMC · Posted

    • RW2018GMC
      Me too……..

      By RW2018GMC · Posted

      from another thread   Update...although the truck sometimes seems to idle weird and the transmission shift a little weird, I've driven about 7,000  miles and no issues.   However, the way GM has handled my rental reimbursement, the situation when my truck quit, and the recall in general has led me to this point...I have driven a GM vehicle for the past 46 years and unless I buy a C3 Corvette, this is the last GM vehicle I will ever own. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...