Jump to content

Recommended Posts

Posted

I wanted to post this cause it worked for me. 
My drivers side door would not open from the inside or the outside. It was like it was stuck between locked and unlocked. The door stuck closed so it was not going to be easy to remove the door panel.  I did research online and could not find an easy option to try.  Here is what I did. 
I leaned on the door between the outside door handle and the edge of the door to take pressure off of the latch. While leaning on the door I pulled the outside door handle and popped open. I then lubed up the actuator and operated the latch several times. It works perfectly now.  I won’t say that this will work in every situation, it is something easy to try before you try to take the door panel apart with the door stuck shut. 

  • 4 years later...
Posted

Thank you Fazah,

Lubing the Latch from inside and outside with door stuck shut worked for me.

While your solution did not allow my door to open, it DID have me focus on the latch instead of the lock/unlock slider! I sprayed silicon lube in towards the latch from the inside and the outside, THEN the door WAS able to open. Woo Hoo!!! I then sprayed the latch repeatedly with silicon while cleaning as much grease and dirt as I could from the latch and with the handle held up, I moved the latch open/closed many, many times. I also sprayed and worked the inside lock/unlock slider, the pull handle and the pull handle on the outside too. And for good measure, I repeated the same procedure on the other side.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • I would like to know if I can increase my 2025 Silverado 2500 HD
    • Length/amount of data capture will be important to consider, sifting through 5 minutes of a data log can be enormous when it is stored in milliseconds. Being able to find the 'event' let alone decipher it.   Presumably the driver would notice something and hit a button to capture the 'window' of data. That window has to be large enough for the operator to recognize the event and react accordingly.    The data has to be able to be retrieved easily.   The data has to be able to be understood. Which is the biggest challenge, dealer techs won't even know what most of it is and would likely not even look at it if an owner brought it to them. Meaning the owner, the least educated/qualified, trying to understand it.    How will the data be presented? Could specific PIDs be selected and a timelapse graph be watched? How will a specific value be noted as abnormal? Additionally, a good data logger would be able to 'learn' normal values for a specific vehicle and flag abnormalities automatically. It could in theory watch parameters degrade over time and suggest maintenance as needed. (If the MAF reading begins tapering off for a given set of other readings - MAP, throttle position, Ambient, etc.. a flag to check air filter.) With the amount of data available, a device (really the vehicle rather than an additional accessory) should be able to do more than issue a DTC. It should be able to run the full diagnostic suite automatically and present a solution rather than a code. (It's not the 90's anymore). The technology is available for the vehicle to not just say "P0087", it should know low fuel pressure, check other PIDs to narrow down the problem itself, and determine if it is a lift pump, high pressure pump, regulator, leak in the fuel line, clogged filter, etc. Even if it can't narrow it down, it should be able to guide the user to the likely problems.   This would be a major problem for dealer service departments, which are the manufacturers customers it is in their collective best interest to NOT have this available to the consumer.   Further, if the owner is going to be the primary consumer of the data, it's got to be at a consumer price point vs. dealer only specialty tool price.   This group is more 'involved' in their vehicle than general public/consumer and will have knowledge, experience, needs and desires that are quite different from the market at large.   
    • I put the prof up. If you read what I posted. You can see that housing, cars and income are in line with the era we were talking about. It’s harder in some places easier in others. Let’s agree to disagree and put this back on track, OK? We both are pretty stubborn and hard headed. But I bring receipts. If you wish I will not respond to you in the future. 
    • Lets see if I can sum up two pages of nothing useful.    You want to refute your own governments data of the "Purchasing Power" Index FOR THE ENTIRE USA and its territories replacing it with the experience of a single family and its business and label that reality?  Then pound on that for a week hoping it will find traction?    Stan, I've told you several times. I don't do irrational. There are more people in the USA than your family.    I'm pretty sure this tread is so blown up. I'll give you a few days or months if need be to post yourself silent then I'll see if I can find enough parts of the train to reassemble it. 
    • Facebook groups hate VSE, poor customer service; their responses to criticisms are pretty poor for a reputable company. I'm not a customer, haven't bought anything from them, but how they handle themselves on social media is a definite "No" for me. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...