Jump to content

More Electrical Issues

Ian Mills
 Share

Recommended Posts

Ian Mills Enthusiast

Ian Mills

Posted
Posted

So I'm trying to chase down some sort of electrical issue that results in lost communication and low voltage codes intermittently. I had previously suspected a bad ground or failing module but today I was driving, CEL came on, and I noticed that my voltmeter was hanging out at <12. 

I pulled over (the gauge came up a bit right when I came to a stop) and read the voltage at the battery and alternator with my multimeter. Both were reading between 12.9 and 13.2. That's not right... right?

The other questions is: is this another symptom or is this potentially what's causing all my communication codes (U1041, U1026, U0101, etc.) and low voltage codes (P0332, P0327, etc.)?

How low would the voltage need to dip momentarily for the computers to start throwing codes like that?

Ian Mills Enthusiast

Ian Mills

Posted
  • Author
Posted

I had the same issue this morning with the voltmeter showing significantly below 14. I read the voltage and it was 12.8. 

However, I turned the truck off and back on and the voltage was 14.7.

Would this be fixed with a new alternator?

The current alternator is only about 6 months old (Ultima R110073A)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,950
    Total Members
    8,960
    Most Online
    Policeoff01
    Newest Member
    Policeoff01
    Joined

  • Who's Online   4 Members, 1 Anonymous, 745 Guests (See full list)

  • Latest Articles

  • Posts

    • Another JR
      Parking Brake - Automatic Engagement Questions

      By Another JR · Posted

      On 2021 3500hd it consistently sets automatically when selecting park if the incline/decline is above a certain angle. 
    • Policeoff01
      Feeling Vibration and Jiggles in 2024 HD Gasser Steering Wheel

      By Policeoff01 · Posted

      Curious, did anyone ever get a fix for the vibration reported here.   I have a 2024 Silverado with 6.6 duramax.   I’m noting the same vibration resonating up through the steering shaft into the steering wheel.    Best way to describe- like someone is tapping on the steering shaft/components and it’s resonating into the steering wheel.    thanks. 
    • Gkistler
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By Gkistler · Posted

      Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...