Jump to content

Drilling the chrome bumper

Tobes

By Tobes
in 2000-2014 Silverado HD & Sierra HD

Recommended Posts

Tobes Enthusiast

Tobes

Posted
Posted

So I pick up this flushmount backup camera on ebay to finish off the Pioneer system in the truck. The perfect mounting place looks to be just to the left of the license plate on the back. The only problem is that the bumper is chrome. Will I run into a problem if I drill the 1" hole in to the bumper that is required to install the camera? I don't want the bumper to start peeling. Is there a specific bit I should be using or a specific technique that will keep me from killing the bumper? The other option would be to drill the license plate and install it there, but mounting would not be as secure (and it might look like cr@p).

 

Any help would greatly be appreciated.

 

:crackup::):D

Wingnut Senior Enthusiast

Wingnut

Posted
Posted

Just use a good, sharp bit, and be sure of where you're drilling because there aren't second chances on a 1" hole. :crackup:

 

Oh, and cover the whole area to be drilled in tape, this should minimize chipping of the chrome plating.

Tobes Enthusiast

Tobes

Posted
  • Author
Posted

Thanks....I will give that a whirl. This should be the last thing I do (at least until I figure the next thing out) :crackup:

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,835
    Total Members
    8,960
    Most Online
    ballencd
    Newest Member
    ballencd
    Joined

  • Who's Online   4 Members, 1 Anonymous, 595 Guests (See full list)

  • Latest Articles

  • Posts

    • mark249
      Help purchasing a touch screen digitizer

      By mark249 · Posted

      Brought my 2015 Colorado into the dealership to check my touch screen issues, had that ghost touch thing happening. They said I needed a new touch screen and they could either order me one for $500. The lady at the service deck was nice enough to tell me I could order a touch screen online for less, she did stipulate that the touch screen had to be factory OEM, you can't pair an aftermarket screen to my radio seeing it was 2015, it had to be a GM factory OEM only. I found a few on Amazon and Ebay by the numbers on the back of the old screen, DJ080PA-01A GM# 22740886, Some said "OEM" in the description and others just said "Replacement". Would a replacement be the same as a OEM as long as it had the same numbers on the back of the screen? In some of the descriptions they also show different brand names but same numbers, is that an issue?  
    • Donstar
      Navigating senior years.

      By Donstar · Posted

      I have both but typically use the 4 legged walker (wheels on front, ski's on back).   The four wheeler is starting to be used on "longer" outdoor walks.  The 4 legged walker is particularly helpful in practicing good walking posture.  Both of my knees are at different stages of recovery and I'm trying to not develop poor habits.  I can actually manage with a cane but it's very difficult not to favor one leg over the other.  My PT recommends I continue with my 4 legged walker for a while.  Yesterday was four weeks since my last knee replacement and I'm excited about my progress to date.  It has been a hell of a rough journey so far but it is exciting to witness  systematic and continuous improvement.  I went for years watching the decline of my "mobility".  It seems that everyday now I am alerting my wife to something I can do now that I couldn't a day or two ago!  I encourage anyone facing the prospect of knee replacement to share any concerns with others who have had the surgery.  It isn't an instant fix but rather is a considerable amount of short term pain for long term gain.  Recovery time and pain levels vary for individuals post surgery but the end results are typically very positive and I've never encountered anyone regretting having had the surgery. 
    • diyer2
      AFM Disabler Question

      By diyer2 · Posted

      The lifter issue can be dealt with by shorter oil changes and quality oil IMO.
    • diyer2
      Winter Returned

      By diyer2 · Posted

      Got heavy rain, hail and light rain yesterday. 
    • Core-Lokt
      Wiring Help, Please

      By Core-Lokt · Posted

      I'm putting in an A-pillar pod/gauges, and I'm asking if anybody can identify a (preferably) fuse for a switched power and illumination circuit on the driver's side interior fuse panel. Offhand, everything I checked with a test light was constant-hot, and I'd much rather uses a piggyback fuse. I can certainly find a wire, but I'd rather not half-tap.   Thanks in advance for any help.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...