Jump to content

Tons of new pics

Mighty HD

By Mighty HD
in Hobbies, Tech & Outdoors

Recommended Posts

Mighty HD Senior Enthusiast

Mighty HD

Posted
Posted

Click on my sig, then click on the 3-10-05 album.

 

Lemme know what cha think.

 

It's been about a month since it was waxed using #26. I am going to get some Menzerna to seal with next time.. :happysad:

Mighty HD Senior Enthusiast

Mighty HD

Posted
  • Author
Posted

Waxing usually takes about 2 hours. I typically wax every other month using #26. I have been reading a lot at www.autopia.org and the information there is unbelieveable. A few things I was doing wrong, but now I've changed

 

I now use a lambs wool mitt to wash

Waffle Weave microfiber towels to dry -- not soft bath towels

I am going to buy a porter cable buffer

Microfiber towels are your friend

You wouldn't believe the shine you can obtain from Menzerna FMJ. They have a car care kit that's just under $90 I think. You put it on iwth a buffer, and the FMJ sealer by hand. The depth is unbelieveable, durability is 100+ days (confirmed), and is much much cheaper than wax. Even though it's $90, you only use something like .5 oz per vehicle, so you can get a LOT of use out of a 32oz bottle.

 

For my engine:

 

I use purple stuff degreaser 100% out of the bottle....soak the motor. NO I don't cover any of the electronics or alternator up :wtf: The engine gets wet when it rains so NO you arent going to have a problem. I then drive it for about 30 min to dry the engine, and then spray armor-all detailers advantage tire foam on everything. It looks better than the day it rolled off the showroom floor.

 

Thanks guys! :nopity:

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • asilverblazer
      Slate Electric Truck

      By asilverblazer · Posted

      I like the idea.  I would pick diesel if I had a choice. I need pictures though.
    • newdude
      Help purchasing a touch screen digitizer

      By newdude · Posted

      I've installed cheap eBay new aftermarket digitizers before.  They work.  Did a bunch of Cadillac CUE (aka Cadillac's MyLink) for someone years ago.  They all worked fine after the repair.    That number 22740886, that is a component part # for GM.  You can use it to search, but its not something that's obtainable at the dealer level.     So pretty much any of these will work - 2015 Colorado Digitizer for sale | eBay
    • asilverblazer
      give me some tips to make my truck look better

      By asilverblazer · Posted

      Black bumper and the later years Z-71 style color matched grille.
    • fondupot
      Exhaust heat while towing!

      By fondupot · Posted

      You can install tailpipes that direct the exhaust sideways vs the OEM one that goes straight back. There are several on the market, do you own research. HOWEVER, you need to make sure the Venturi vents are still intact, otherwise it will throw a engine code. There is a sensor somewhere that detects back pressure on the exhaust. And if it doesn't collect the correct metrics, it will throw the truck into limp mode. 
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      "Teardown" is complete. Head surfaces are clean and ready, new intake is prepped and ready. Coolant drained and water pump is removed, radiator is removed, new hoses and pump are ready.   The replacement intake is also from a '95 (with I think 260k, the odometer said). Noticeably less pitting where it covers the rear coolant passages. I'm not sure if that's a tribute to more frequent use, more frequent coolant changes/upkeep, or if the intake was machined at some point. But it appears I found a good one.   My coolant hoses were original, and the lower hose still retained the factory spring inside. It's not really rusty, but it's got deposits all over it. Unsure if I should re-install it (will thoroughly clean it first). Someone said hose technology has gotten better since 1995 (has it?) and I don't need the spring. I think modern EPDM is what made those hoses last from 1995-2026, so it's a question of how much suction can the water pump really pull, and will it collapse the hose without a spring?   I'm stopped and waiting for parts, however.   When I first brought the truck home, the fan was intermittently hitting the radiator shroud. I could see someone had monkeyed with the shroud (put a bunch of cardboard as a spacer between the upper/lower shroud halves. Someone said the motor mounts have likely failed and the engine has sagged. I wasn't sure I believed that. The engine is really solid in its mounts: To remove the old intake I *just* nearly permanently welded to the heads with freshly cured RTV and gasket snot two weeks ago, I literally had to use the arms on my lift and a chain with a bolt attached to the intake to pull it loose. It almost picked the front of the truck off the ground before ....scuuuuuuuuuuup.... I could actually hear the gaskets tearing and it broke loose and the whole truck settled back down. Motor barely moved.   SO, those parts I'm waiting on... The lower radiator mounts/bushings had completely failed. The radiator needs to be insulated from the rad support, and the bushings help the rad stand at the correct height. The plastic "baffle" was also destroyed at some point. Someone had attached the shroud to it incorrectly, overlapping a joint that should have been underlapped, creating another suspect issue potentially causing things to hit the fan. Broken tabs, side is busted off, and it's perma-formed/bent where it was jimmied incorrectly.   The baffle? Unobtainum. Long since discontinued from GM, of course. Aftermarket/capa/chinese? Also unobtanium. In GM's infinite wisdom, it appears there are at least two different variations whether the Blazer is 2 or 4 door, and I can't yet tell if they shared the same part with the S-pickups. Plan B, if I can't find a viable used one, will be to create a bracket to re-assemble the critical joint I need to seal a gap with the shroud. But that will bug me, it won't be...perfect.   The water pump bolts appear to have been installed with...plumber's putty. I guess, sure, if it works...? I've found a few "backyard fixes" like that. Someone's been here before....   If I can't find someone to jam bamboo under my fingernails to fill my free time this week I think I'll install the driver's power window motor and replace the rear door speaker that's inop. I've got a genuine GM "9.5" ohm working replacement. Why GM used a non-standard resistance....nevermind. Of course they did, you can get more sound from a cheap factory amp that way.   And the saga goes on...

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...