Jump to content

7.4L exploded view ??

Mr. Fixit

By Mr. Fixit
in Ask A GM Technician

Recommended Posts

bobcat5544 Enthusiast

bobcat5544

Posted
Posted

here you go

2164061_37_full.gif

(1) Timing Chain

(2) Camshaft Sprocket Bolt

(3) Camshaft Sprocket

(4) Crankshaft Sprocket

(5) Camshaft Retainer Bolt

(6) Camshaft Retainer

(7) Camshaft Bearings

(8) Camshaft

(9) Valve Lifter Guide Retainer Bolt

(10) Valve Lifter Guide Retainer

(11) Oil Pressure Sensor

(12) Valve Lifter Guide

(13) Valve Lifter

(14) Cylinder Head Locating Pin

(15) Engine Block

(16) Oil Pan Gasket

(17) Oil Pan

(18) Oil Pan Bolt

(19) Oil Filter

(20) Oil Filter Fitting

(21) Oil Filter Adapter Bolts and Plugs

(22) Oil Filter Adapter Assembly

(23) Oil Filter Adapter O-Ring

(24) Engine Block Coolant Drain Hole Plug

(25) Knock Sensor

(26) Knock Sensor Heat Shield

(27) Knock Sensor Heat Shield Bolt

(28) Engine Block Oil Gallery Plug

(29) Engine Front Cover Locating Pin

(30) Engine Front Cover Gasket

(31) Crankshaft Position Sensor

(32) Crankshaft Position Sensor Bolt

(33) Crankshaft Balancer

(34) Water Pump Bolt

(35) Water Pump

(36) Water Pump Gaskets

(37) Engine Front Cover Bolt

(38) Engine Front Cover

 

2164061_38_full.gif

(1) Oil Pump Bolt

(2) Oil Pump Screen

(3) Oil Pump

(4) Oil Pump Locating Pins

(5) Oil Pump Driveshaft Retainer

(6) Oil Pump Driveshaft

(7) Crankshaft Thrust Bearing Cap

(8) Crankshaft Lower Thrust Bearing

(9) Crankshaft Rear Oil Seal

(10) Engine Flywheel (Manual Transmission)

(11) Clutch Pilot Bearing

(12) Engine Flywheel Bolt

(13) Crankshaft Upper Thrust Bearing

(14) Crankshaft Bearing Cap Oil Seal

(15) Engine Flywheel (Automatic Transmission)

(16) Engine Flywheel Bolt

(17) Engine Block

(18) Piston

(19) Piston Ring Assembly

(20) Connecting Rod Bolt

(21) Piston Pin

(22) Connecting Rod

(23) Connecting Rod Bearings

(24) Connecting Rod Cap

(25) Connecting Rod Nut

(26) Crankshaft Upper Bearings

(27) Crankshaft

(28) Crankshaft Position Sensor Reluctor Ring

(29) Crankshaft Lower Bearings

(30) Crankshaft Bearing Cap

(31) Crankshaft Bearing Cap Bolts

 

2164061_39_full.gif

(1) High Voltage Distributor

(2) Fuel Rail Bolt

(2) Fuel Rail Bolt

(3) Fuel Rail Assembly

(4) Ignition Coil

(5) Ignition Coil Bolt

(6) EGR Valve Bolt

(7) EGR Inlet Pipe

(8) EGR Inlet Pipe Fitting

(9) Lower Intake Manifold End Gaskets

(9) Lower Intake Manifold End Gaskets

(10) Lower Intake Manifold Bolt

(11) Lower Intake Manifold Side Gasket

(12) Lower Intake Manifold

(13) Thermostat

(14) MAP Sensor

(15) MAP Sensor Bracket

(16) MAP Sensor Bracket Nut

(17) EGR Valve Gasket

(18) EGR Valve

(19) Upper Intake Manifold Gaskets

(20) Water Outlet Housing

(21) Water Outlet Housing Studs

(22) EVAP Purge Valve Bolts

(23) EVAP Purge Valve

(24) Upper Intake Manifold

(25) Upper Intake Manifold Bolt

(26) Throttle Body Gasket

(27) Throttle Body Stud

(28) Throttle Body

(29) Governor Bracket (RPO 9C2 only)

(30) Distributor Clamp Bolt

(31) Distributor Clamp

(32) Ignition Coil Stud

2164061_40_full.gif

(1) Valve Rocker Arm Bolt

(2) Valve Rocker Arm Ball

(3) Valve Rocker Arm

(4) Pushrod Guide

(5) Spark Plug Wire Bracket

(6) Exhaust Manifold

(7) AIR Tube (California Only)

(8) AIR Tube Check Valve (California Only)

(9) Exhaust Manifold Center Bolt

(10) Heat Shield Nut

(11) Heat Shield

(12) Exhaust Manifold Gasket

(13) Exhaust Manifold Stud

(14) Valve

(15) Cylinder Head Gasket

(16) Valve Seat

(17) Valve

(18) Valve Rotator

(19) Valve Stem Oil Seal

(20) Valve Spring

(21) Valve Cap

(22) Valve Keys

(23) Cylinder Head

(24) Cylinder Head Bolt

(25) Valve Guides

(26) Valve Pushrod

(27) Valve Rocker Arm Cover Gasket

(28) Valve Rocker Arm Cover

(29) Valve Rocker Arm Cover Bolt

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,860
    Total Members
    8,960
    Most Online
    HWN808
    Newest Member
    HWN808
    Joined

  • Who's Online   4 Members, 1 Anonymous, 721 Guests (See full list)

  • Latest Articles

  • Posts

    • richard wysong
      Gas Prices

      By richard wysong · Posted

      Diesel $5.42 at the truck stop on the hi-way
    • Chuck FB
      Joke Thread

      By Chuck FB · Posted

    • txab
      Gas Prices

      By txab · Posted

      $3.59  
    • needafix
      2019+ Brake failure, it's complicated

      By needafix · Posted

      I'm not sure if this should be a new topic, let me know if it's out of place. This my first post. Thanks 85077522 - AC Delco GM Genuine Parts Brake Master Cylinders. Anyone else had to replace this brake master cylinder yet. I didn't do any brake work, it looks like new parts and I've had the truck for about 4k miles, 119k total miles.  When it started to throw codes I did the calibrations with a bidirectional scanner and got the codes to clear but they came back so I did the routine; base bleed, automated bleed and final base bleed. All that with Bosch ES16-32N fluid (please look it up). That seemed to fix it but 100ish miles later it failed again so I ran the same process but with a pressure bleeder this time and got the same results, fixed for 100ish miles. The original fluid looked bad and I thought I got most of it out, it could've been the wrong fluid. The codes; P25A2, C05B0-00, C2A1B. I can get them to clear but not for long. The C05B0 indicates a leak in the front circuit (which is bone dry) so I'm thinking of doing the bleed process on that front again today and I don't know if that's taboo to just do the front but at this point it seems like it's worth the try anyway. The new master cylinder/module unit is supposed to get here today. But now I'm pretty much convinced this install is over my head. I've called several shops and some mobile guys that I know but this thing is like radio active material, scary wise. I did get 2 local shops say they should be able to do it, one says he has the SPS2 programing capability. And with the battery disconnected is there supposed to be pedal resistance, mine is to the floor, then if I pump it I can get some resistance. I had a panic stop prior to this issue which may have contributed from what I read. And on the first attempt to bleed and hydraulic test the scanner listed things to look for and one was any gaps between the pad and rotors which I did notice on the RF corner and I removed the outer pad (where the gap was) cleaned it and the hardware and didn't see a gap after that but will re-check it. I read that if pushing the caliper pistons back then you're supposed to open the bleeder so as to not push fluid backwards into the abs module or it will damage it. If that's true then that's also a possibility from the previous owner having the brakes changed before I got it. I'm using an XTool ip500 scanner. Any suggestions, questions and comments welcome. 
    • Donstar
      Navigating senior years.

      By Donstar · Posted

      Next Friday will be my 6 week point from my right knee replacement.  The surgeon says it will be fine if I choose to drive after this checkup.  I know I could drive now but best to do as my surgeon (and my wife) tell me.  Richard compared being 62 to 72.  I remember when I was in my early 60's I was experiencing slow but regular decline in my mobility.  Thanks to good medical support,  i continued to fight the speed and spread of this decline. During my 60's I worked on non-surgical methods and just when I turned 70, my orthopedic surgeon recommended joint replacements.  In a little over a year, I had one shoulder and both knees replaced.  This hasn't been a terribly fun experience, but worth the discomfort as my future mobility health trajectory has reversed.  It is a treat to now be watching my mobility. balance and confidence steadily improve!

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...