Jump to content

Wire Schematics For 04 Silverado Alarm Install

silverdrgn

Recommended Posts

silverdrgn Enthusiast

silverdrgn

Posted
Posted

Hello every1, I am planning on helping a freind install an alarm/remote start in his 04 Chevy Silverado and need the wiring diagram/schematics to the vehicle. I have tried searching on google but the info found was not very helpfull. I tried searching here but also did not find the necessary info. Can anyone help? I was trying to do the install by this Thursday so if anyone has it it would be greatly appreciated if you could drop me a line with the info. TIA to all help.

 

-Jorge -Still a newb. :thumbs:

4drwalker New Member

4drwalker

Posted
Posted

:tear:

Just a word of caution if the plan is to install "extras" like remote start, window & door locking, starter lockout, ect... especially involving Directed Electronics products. (Vipor & Clifford for example) Although good products, the info. needed to install them are isolated to said dealers. Installing the alarm is one subject, but then you start integrating with the factory security which even then can be done realitively easy. With the multiplexed body module & everything else pretty much running off the data bus, you will need specific command modules to overide the "key sense" & specific resistance values embedded in the ignition key; for remote start to work properly. There is also a module to control the door locks that is year/model specific. Otherwise you will spend days installing numerous relay kits & soldering in diodes. They also use different terminalogy while being extremely vague with polarity issues for example. I guess what I'm getting at would be.. without discounting anyones knowledge of electronics, this is better done by the dealer of that specific system. And you also retain the warranty as well. There is just too much that can be misunderstood with grave consequences by misinstalling just one wire or diode.

 

Having said that, if it is a Vipor ect.. then I can give you info. you specifically need that I have "gathered" when installing these systems. Give me specifics about vehicle & I will try to map it out in terms better known to the majority. (factory remote for door locks?, alarm?,dome lamp monitoring?, ect..) Also the make/model alarm system adding in to the truck. If not built by Directed, than I am no help to you. If your trying to install with a schematic that any aftermarket shop manual supplies while matching oranges to oranges in theory should work, but it rarely does. They simply don't want the public trying to install their own system. :confused:

Mighty HD Senior Enthusiast

Mighty HD

Posted
Posted

www.the12volt.com

 

All of the diagrams are there.

 

If it's a viper you will need a 1700G or a 457G module for it to work properly.

 

Diode isolation also is critical.

 

Better be SURE you know what you're doing ........

 

You're better off paying $200 and having it installed.

  • 8 months later...

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Grumpy Bear
      Food & Drink

      By Grumpy Bear · Posted

      Evan Williams Bottled in Bond   So pouring the last of a bottle of Evan Williams Black label last night I set off the the state store for a refill only to be denied the by an empty shelf. Rats.    What the did have was a bottle of Evan Williams Bottled in Bond. 100 proof. Hum, a few bucks more but a known distiller. Lets have a swing at it. ( I have before )    Cracked it open and pour a serving over ice. Hum.... more heat, yes. More alcohol naturally. But the barreling not the proof brings the taste and this one came up short.    Oh is was familiar but the heat ran the barrel over like a Peterbilt runs over a squirrel. Could use a heavier toasting of the oak me thinks or perhaps a longer barreling. Who knows. But what I can say is ice or a water back isn't the answer. What kills one kills them both. Sad. It is a pleasant drink....if you have little to compare it to.  
    • Grumpy Bear
      Bridgestone vs Goodyear tires?

      By Grumpy Bear · Posted

      I've had exactly one set of Bridgestone. Lasted five year and 125,000 miles and had I known better 15oK would have been a cake walk. I would have bought a like set had they not tripled in price since the first set. I removed them at said mileage with 5/32" remaining in dead even wear all four. They were fuel efficient, quite, comfortable and predictable.    Early on I got a very good alignment checked at least once a year, sometimes twice; kept the tires properly inflated, balanced and rotated. And I've found that many a tire issue can be avoided with great maintenance practices. Lot's of tire dealers will do rotation and balance (simple) for free for as long as you own the tire they sold you so no excuse not to.    Bead prep, alloy integrity and stem health have a huge impact on inflation stability. There are more mountings done poorly that perfectly. Finding a good tire guy is gold and as important as finding a tire you like.    That 3X price increase now two sets of "other tires' later is starting look like a bargain.      Bad maintenance kills more tires than bad tires. 
    • Grumpy Bear
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Grumpy Bear · Posted

      Atlas, you kill me As aggravating as a project like this can be you have been unable to hide your fascination with learning and using that angst against this beast like a Ninjitsu Master. It amuses you, admit it now.      BTW, love your writing style. 😉       
    • TrueBlue
      Wow I'm in a pickle. (Broke down truck) and a story.

      By TrueBlue · Posted

      I gotta say, I'm enjoying your narration. The troubles you've been having are amusing as you describe them. It's good to see that you're finally getting some satisfaction out the old beast though.
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Declaring victory would upset the demons that possess this Blazer, so I won't. But I did make progress today--after it put up a fight. Always a fight.   I had the day off so I spent the morning cleaning up the shop and I thought I'd get ahead of things by filling the cooling system in prep for the final part I needed to arrive: the driver's side knock sensor. Glug, glug, glug....and then the unmistakable sound of liquid hitting the shop floor. It induces the same chagrin when the sonar and targeting laser temporarily malfunction during a late night bladder evacuation over the toilet with the bathroom light off. D'OH!!! That made a mess...   Oh, hey, that knock sensor I removed? It threads into a wet port. Who knew?! Learn something new every day. Put a pin in that chore, I'll fill it the rest of the way later.   The knock sensor arrived at about 1pm. I threaded it in, connected the wire, filled up the coolant, checked for leaks, and... drumroll.... fingers crossed for a perfect start, excellent timing, model fuel trims, and ...no squeaks... Here goes.....   No, it didn't start. At all. I cranked it a few times and it wasn't sounding good. Furthermore, I heard leaking again. Jesus H Tapdancing Christ, stop leaking all over the dang floor. This time I had accidentally overfilled the coolant reservoir and the churn of the water pump via cranking caused a bit to burp out. Ok, just, breathe... Put the flamethrower down. Dang thing wouldn't burn anyway, leaks too much...   Did you know the rotation of a round crank sensor in a round hole, matters? I do now. Took me about half hour to retrace steps and realize what I had done. Then it started right up.   No squeaks. The squeak was the old balancer.   Once it entered closed loop, fuel trims are dead on, hovering right around zero at idle. No more -30%. I'll credit the injector rebuild on that one.   Timing? I think there's an OBD 1.5 translation error with my Actron scanner. It's anywhere from -20 to -30 at idle, sometimes as high as -40 cruising. Sorry, the engine just isn't running that smoothly at -40 degrees ignition advance. It's just not. It's smooth all through the rev range and has decent power. I'm going to have to trust the seat of my pants on this one.   The new exhaust is very quiet. The old catalytic converter? Not melted, but definitely not healthy. Rains glitter when you turn it on its end...all the precious metal is flaking out. Once the new exhaust system burned in/smoked off a bit, the engine's exhaust smell is normal again. Not that I'd recommend going around huffing car exhaust, but, you know what I mean?   One problem to correct. The new exhaust has the opposite problem of the old spliced up exhaust. It wants to hit the floor where the old one wanted to rest on the cross member. Happy medium, please? Still noodling on that one, need to look at how I can adjust some hangers.   I don't know what's next. On one hand I want to run away from this thing as far and as fast as I can -- there have been a lot of NOT fun moments. On the other, now that it kinda drives nice, maybe drive it around for a little bit?   Shhh... it's not currently dripping oil all over the floor. I can see just a little wet at the bottom of the timing cover where it meets the oil pan seal. It's not dripping multiple drops with every ignition cycle, in fact, after some driving this evening it has yet to even form a drop that could drip off yet. But the weekend is young... I fully expect this could turn into Exxon Valdez by Sunday. Because this Blazer hates me. LOL.      

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...