Jump to content

2005 Yukon Xl Transmission Fluid/filter

HaroldCallahan

Recommended Posts

HaroldCallahan Enthusiast

HaroldCallahan

Posted
Posted

What fluid for transmission fluid change on 2005 Yukon XL at 20,000 miles. I am thinking Dexron VI, GM Part no 8861003 for the fluid.

 

How many quarts for a remove the pan, drain and replace filter - no flush ?

 

For the filter, I am thinking probably a GM filter. Anybody know the GM number for the filter ? Is the transmission in the 2005 Yukon a 4L60E or 4L80E ?

 

I found decent price online for the fluid, probably better than the local dealer.

 

Also, probably should change the transfer case fluid as well. What should I use for the Transfer Case ?

 

Any advice on what to use and where to get it is appreciated.

 

Thanks

05swb53l Enthusiast

05swb53l

Posted
Posted

I don't know about the tranny... You should be able to use your rpo codes in your glove box to figure out which tranny it is.. As far as the transfer case, if it has an autofwd button on the dash with the 2hi 4hi 4low... then it would be autotrakII from the dealer.. If it has the auto4wd, don't use tranny fluid in the transfer case..

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,840
    Total Members
    8,960
    Most Online
    appletrav
    Newest Member
    appletrav
    Joined

  • Who's Online   5 Members, 0 Anonymous, 711 Guests (See full list)

  • Latest Articles

  • Posts

    • Core-Lokt
      Wiring Help, Please

      By Core-Lokt · Posted

      Thanks; I looked there a few minutes, and I think I can find something. I really never looked there, as I thought it was stuff like PTO/aftermarket bodies/accessories like snow plows.
    • newdude
      2 speed transfer case optional now?

      By newdude · Posted

      This is a 1/2 ton thing ONLY.  All HDs 2020-2026 have the two speed transfer case, with Autotrac as an option.     1/2 tons 2019-2026, regular 4x4s come with a single speed case (no 4LO!), and trucks with Z71 ordered, or all Trail Boss trucks come with the 2 speed case.  2 speed case is also an option on WT, and is also standard on High Country.  
    • newdude
      Different requirements for oil filters?

      By newdude · Posted

      2013 5.3 still to this day calls for the PF48 filter.  Which as a 15psi bypass pressure.     There is a TSB, 17-NA-157 that talks about the PF-63 and PF-64 filters which have a higher bypass rating of 22psi.    TSB HERE - temp.xml   "Beginning in 2012, the oil pumps began to regulate main gallery feedback instead of pump out pressure. This means that the oil pump now does not begin to regulate until pressure is built up to the main gallery. This change reduces the amount of time it takes to provide oil to the engine bearing and lifters during extreme cold start conditions.  Main gallery feedback oil pump control systems are present on the following engine families which use Spin-on oil filters: Small Gas Engine (SGE), Large Gas Engine (LGE), High Feature (HFV6) Gen2 and Small Block Gen5 gasoline engines. These engines with the main gallery feedback oil pump control systems are factory built with an ACDelco® oil filters"   It also calls out what engines use those filters.  The gen 4 small blocks were not on that list (LMG, LC9, L9H, L92, L94, L20, L96).  Gen 5 small blocks use the higher pressure filter.          That all said...   Your 7045 Napa filter is the PF63 equivalent, with 22psi bypass.  You are already using the higher bypass pressure filter.  You CAN keep using it, you don't technically have to use it though.  
    • Grumpy Bear
      Different requirements for oil filters?

      By Grumpy Bear · Posted

      Do you know WHY the filter relief setting was increased to 22 psig?    When the new system goes into the second stage the pump volume ramps up considerably. It was found that the 15 psi filter bypass setting put the filter in bypass on a warm engine when the second stage was activated. Raising the filter bypass setting forced the filter to do what it designed to do. Filter. Preventing debris from circulating during high load, high rpm operation.    So next question is how did GM find this out? VLOM/lifter failures and a deep dive by Melling Corp.    Last question. Is it required? Look at it like this; a motor may be equipped with a rev limiter. But it only works if the set point in reached. That 22 psig setting only matters if the pressure differential across the filter media exceeds 15 psig during normal warm operation. Second stage kicks in around 3000-3500 rpm.    I can't answer your question because I don't know you and how you use the truck. But I think there is enough information here to let you decide for yourself. 😉
    • Coastie05
      give me some tips to make my truck look better

      By Coastie05 · Posted

      Go back to OEM wheels. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...