Rough Country Or Superlift

[small1town9kid]

ok so whats yall opinions of the NBS roug country kit. pics and testimonials are welcome.

 

i'm tryin to deside between the knuckle kit that seems good deal for the money or savin more for a full drop and crankin it to 7.5 (the superlift). i don't need that much. i already have a 3 inch body lift and the biggest i wanna run IFS is 37s or 38s. so i don't need it but i night want the extra couple inches just to have them. what would yall do?

[small1town9kid]

BUMP

[Zembonez]

BUMP

Pretty hard to beat the Fabtech knuckle setup. Their knuckles are well engineered and tough too.

 

Just my 0.02

[small1town9kid]

i haven't heard too much good about the fab tech kits.. thats why i'm reallly unsure about them

[Majorleaguebass]

it is for your 2004 silverado???

[Zembonez]

i haven't heard too much good about the fab tech kits.. thats why i'm reallly unsure about them

I've had two Fabtech lifted trucks. The last truck I had a Fabtech suspension lift on went about 80,000 miles before I sold it and even the alignment stayed right on. Well built stuff... especially their spindles. The ONLY time I ever heard anything bad about them it was from people who didn't sell them. Not very solid info... just trying to sell what they stocked.

 

In my opinion their stuff was great. No problems.

[small1town9kid]

yes it's for my 2004 silverado half-ton

[silverbullet2005]

Rough Country is JUNK!!!

 

Go with BDS or SuperLift if you want a good quality kit

[small1town9kid]

Rough Country is JUNK!!!

 

Go with BDS or SuperLift if you want a good quality kit

 

 

how ya figure about Rough Country?????

 

but ya i've been thinkin about still savin more and doin the 7.5 superlift

[flyin6]

Rough Country is JUNK!!!

 

Go with BDS or SuperLift if you want a good quality kit

 

 

how ya figure about Rough Country?????

 

but ya i've been thinkin about still savin more and doin the 7.5 superlift

 

 

I just went through this decision cycle. I discovered the RC kits for the GMT900 series has some serious problems and had many unhappy owners. That doesn't reflect on the torsion bar kit as far as I know, but I did check out their customer service and did not get answers or some "Fuzzy-Math" sort of response.

 

So, I ended up buying the Superlift. Do a search on this site and you'll find all good information on the superlift kits.

[cjchinnici]

Rough Country is JUNK!!!

 

Go with BDS or SuperLift if you want a good quality kit

 

 

how ya figure about Rough Country?????

 

but ya i've been thinkin about still savin more and doin the 7.5 superlift

 

 

I just went through this decision cycle. I discovered the RC kits for the GMT900 series has some serious problems and had many unhappy owners. That doesn't reflect on the torsion bar kit as far as I know, but I did check out their customer service and did not get answers or some "Fuzzy-Math" sort of response.

 

So, I ended up buying the Superlift. Do a search on this site and you'll find all good information on the superlift kits.

 

 

 

I have a 2008 silverado z71 and am looking for a lift but i do not want to cut or grind anything. is there any other bolt ons like a rough country but with a lil more than 3 inches

[Ranger]

My RC lift works perfect, and I even have the older system (with the 2 small shims per side)...

[flyin6]

I'm right in the middle of installing the Superlift 6" kit. I'm also doing a double-cardan driveshaft so I won't have the vibration problems since I have AWD. WIll post a new thread showing the install when I get it done!

[cjchinnici]

I'm right in the middle of installing the Superlift 6" kit. I'm also doing a double-cardan driveshaft so I won't have the vibration problems since I have AWD. WIll post a new thread showing the install when I get it done!

 

 

What lift could i put on that has no cutting and grinding besides a RC. Thanks