Jump to content

best way to lift front end on 2002 sierra 2500HD


Recommended Posts

Posted

hey,

i went to local spring shop and got another leaf put it and it raised the rear end. i want to know the best,safest way to raise the front 2-3 inches. ive read alot about the torsion keys and know to crank them up to max 2 inch lift.

my buddy was saying you don't really want to do this because it changes alot in the front end and he suggested just to get the leaf taken out later.

I would perfer to leave the AAL in and raise the front. would getting other shocks do anything or is cranking the torsion keys the only way to raise the front end. I figure that the leveling kits are just tthe same thing, cranking up the keys

 

thanks

Posted

Shocks wont do anything for height.......

 

I'm not into the lifting stuff but I wonder if they make front air-lift bags, like they do for the rear.... :dunno:

 

http://shop.airliftc...rch?k=0&q=81560

 

BTW...... It would help a lot if you would list the year/model of your truck.....2WD...4WD etc in your signature line.

Posted

Just crank the torsion keys. On and HD you can get up to 2.5" out of em without damaging anything or altering the ride quality much. People think that cranking the keys will destroy your front end, but it wont hurt anything as long as you dont over-crank them. New shocks wont do anything for raising the height.

Posted

Shocks wont do anything for height.......

 

I'm not into the lifting stuff but I wonder if they make front air-lift bags, like they do for the rear.... :dunno:

 

http://shop.airliftc...rch?k=0&q=81560

 

BTW...... It would help a lot if you would list the year/model of your truck.....2WD...4WD etc in your signature line.

 

 

it's in the title 2002 sierra 2500HD 4WD

Posted

Thanks..... When we are reading a post, we don't usually see the title. I mentioned it for your benefit.... as well as ours...... :D

Posted

Just crank the torsion keys. On and HD you can get up to 2.5" out of em without damaging anything or altering the ride quality much. People think that cranking the keys will destroy your front end, but it wont hurt anything as long as you dont over-crank them. New shocks wont do anything for raising the height.

 

 

^ This. Don't waste your money on a new set of keys. Just crank your stock ones. If you don't get the look you want, remove the real add-a-leaf or buy an actual suspension lift for the front.

  • 4 weeks later...
Posted

hey,

i went to local spring shop and got another leaf put it and it raised the rear end. i want to know the best,safest way to raise the front 2-3 inches. ive read alot about the torsion keys and know to crank them up to max 2 inch lift.

my buddy was saying you don't really want to do this because it changes alot in the front end and he suggested just to get the leaf taken out later.

I would perfer to leave the AAL in and raise the front. would getting other shocks do anything or is cranking the torsion keys the only way to raise the front end. I figure that the leveling kits are just tthe same thing, cranking up the keys

 

thanks

 

 

Curious, how much did it cost for the add a leaf in the rear? Also, how much height did that add?

Posted

Cost me the time it took to unbolt the U-nolts and swap in the new leaf. Its really too easy to pay someone else to do it. I got about 2.25" - 2.5" IIRC.

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,915
    Total Members
    8,960
    Most Online
    ChristopherDobson
    Newest Member
    ChristopherDobson
    Joined
  • Who's Online   3 Members, 0 Anonymous, 1,254 Guests (See full list)

  • Latest Articles

  • Posts

    • Monthly payment is only part of the equation. With today's prices and interest rates, I'd look at the total monthly cost: payment, insurance, registration, fuel, maintenance, and expected repairs. A vehicle that fits comfortably into your budget is usually the better choice than stretching for a higher trim. I've also kept my vehicles longer over the past few years. New cars have gotten expensive enough that driving one for 10+ years, while staying on top of maintenance, often ends up being the most cost-effective approach.
    • 10 Ford and Chevy engines proven to reach 300,000 miles   You may note a common 3K OCI on this list of gas motors. I skipped over the diesels. Dh'O. 
    • Thanks newdude!  By the time manual selection is needed, I'm probably too much of a control-freak to depend on the transmission sensing braking to activate automatic downshifting.  I would be anticipating the situation and already be manually downshifting.   This truck replaced a 2004.5 LLY diesel with the Allison 5-speed.  Putting it in T/H made noticeable differences (when the torque converter locked, upshift points, downshift behavior).  On this 2024 gasser with the 10L1000 I haven't been able to detect much, if any, difference.  Ok, I can never tell now when the torque converter locks up.  But I also don't notice differences in shifting.  For downhills, I've probably already manually downshifted by then anyway.  Since it's also more awkward (than the 2004.5) to engage/disengage I don't even bother.  Or maybe it doesn't really matter with just a 3k lb. camper in the bed?   Thanks also for the list of reasons the charging system might select various voltages.  However, what I am seeing doesn't fall into any of those categories.  It very definitely, and very consistently, rises after coasting/braking.  Maybe not immediately, but not very long after coasting/braking.  Very consistently drops voltage when no longer coasting/braking.  It might also be interacting with the camper battery charging (I might disconnect the camper and see if it changes the charging behavior).  I also need to recheck turning on headlights for when I want to force it to charge the camper.   Another JR, in June I converted the camper to LiFePO4.  Since it's not a good idea to try to charge lithiums directly using truck, I installed a Victron Orion XS DC-DC charger (which BTW is AMAZING!!).  Being cheap, I only had to buy that one item (besides the battery, of course) to do the conversion.  The camper OEM 120v battery charger (only 19 years old and works perfectly) and the truck feed the input to the DC-DC charger (not at the same time).  But I didn't want the camper charger feeding back to the truck so I kept the old separator.  I considered replacing the separator with a 30amp diode but that means more work and might add another 1/2 volt drop.  One thing that surprised me was the voltage drop over the long 10awg wire run, so I can only charge smoothly at 8 amps (because the DC-DC charger is completely configurable).  Another reason I don't want an added voltage drop with the diode.  I might also be a little lazy but all this work is being done under the sink with a small cabinet opening.    
    • apparently CA smog is (or at least was)  checking that the vehicle is using the oem and/or a ca smog approved tune, so I expect you'll fail inspection doing it.
    • yes, leaking exhaust will mess up o2 sensor readings, which in turn messes up fuel trims.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...