Jump to content

Power steering hose nut sizes

jseabolt
 Share

Recommended Posts

jseabolt Enthusiast

jseabolt

Posted
Posted

So the high side pressure hose on my '98 1500 Express 143,000 miles finally decided to spring a leak. Well it had been leaking for awhile, just got worse all of a sudden.

 

So I get a new hose and before installing it decided to see what line wrenches the fittings take. The small fitting that goes into the steering box (or rack?) was 5/8". Flip the wrench around to 11/16" and it won't fit the larger nut.

 

I get out my digital caliper and measure both nuts. The small nut comes to 15.9 mm, the bigger nut comes to 17.9 mm.

 

I thought perhaps it was just the new hose but the fittings on the factory hose are also 16 and 18mm.

 

HMMMM.

 

I look through my toolbox and I have no 16/18 mm line wrenches. I go down to the autopart stores and they have none. Of course they had nothing as well. Do they even make a 16/18mm line wrench?

 

I go through both sets of my metric wrenches and I don't even have an 18mm wrench ! However I did have an 18mm stubby. I couldn't get enough torque on it so I placed an old jack handle I use as a cheater bar on the closed end and smacked it with a hammer to break it loose. I didn't care if I rounded it off or not.

 

So i resorted to using the 5/8" line wrench at the rack or steering box and the 18mm stubby on the larger nut going into the bottom of the pump.

 

My last resort was to use an adjustable wrench but luckily it didn't come to that.

 

My question is has anyone ever ran into this before? Why would GM use an 18mm fitting when an ordinary 18mm wrench is not even that common.

 

 

 

bronyaur Enthusiast

bronyaur

Posted
Posted

I had to buy an 18mm open-end wrench just for this. I never found an 18mm flare-nut wrench, but I've not had any issues using the regular open-end. I don't know why GM did this.

  • 4 years later...
Littlejohn19 New Member

Littlejohn19

Posted
Posted

They did it so you would take it to them so they can charge you an arm and a leg to replace it. Harbor freight has a set of crows foot wrenches which they call flare nut 16mm and 18mm sizes you need for $35.00. You can pay for the wrenches by buying the hose from parts geek for $18.00 vs. Oreilly $69.00. Would be surprised if dealer would it for less than $500.00. You know you have to pay for their rags.

Brian Lindsey Enthusiast

Brian Lindsey

Posted
Posted

gearwrench has a complete flair nut wrench set , used to have a sale , buy metric set and get sae set,  6  wrenches in each  set , it was about 70.00 for both sets

  • 8 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,972
    Total Members
    8,960
    Most Online
    Whit.the.COB
    Newest Member
    Whit.the.COB
    Joined

  • Who's Online   3 Members, 0 Anonymous, 1,227 Guests (See full list)

  • Latest Articles

  • Posts

    • Grumpy Bear
      Bridgestone vs Goodyear tires?

      By Grumpy Bear · Posted

      I've had exactly one set of Bridgestone. Lasted five year and 125,000 miles and had I known better 15oK would have been a cake walk. I would have bought a like set had they not tripled in price since the first set. I removed them at said mileage with 5/32" remaining in dead even wear all four. They were fuel efficient, quite, comfortable and predictable.    Early on I got a very good alignment checked at least once a year, sometimes twice; kept the tires properly inflated, balanced and rotated. And I've found that many a tire issue can be avoided with great maintenance practices. Lot's of tire dealers will do rotation and balance (simple) for free for as long as you own the tire they sold you so no excuse not to.    Bead prep, alloy integrity and stem health have a huge impact on inflation stability. There are more mountings done poorly that perfectly. Finding a good tire guy is gold and as important as finding a tire you like.    That 3X price increase now two sets of "other tires' later is starting look like a bargain.      Bad maintenance kills more tires than bad tires. 
    • Grumpy Bear
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Grumpy Bear · Posted

      Atlas, you kill me As aggravating as a project like this can be you have been unable to hide your fascination with learning and using that angst against this beast like a Ninjitsu Master. It amuses you, admit it now.      BTW, love your writing style. 😉       
    • TrueBlue
      Wow I'm in a pickle. (Broke down truck) and a story.

      By TrueBlue · Posted

      I gotta say, I'm enjoying your narration. The troubles you've been having are amusing as you describe them. It's good to see that you're finally getting some satisfaction out the old beast though.
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Declaring victory would upset the demons that possess this Blazer, so I won't. But I did make progress today--after it put up a fight. Always a fight.   I had the day off so I spent the morning cleaning up the shop and I thought I'd get ahead of things by filling the cooling system in prep for the final part I needed to arrive: the driver's side knock sensor. Glug, glug, glug....and then the unmistakable sound of liquid hitting the shop floor. It induces the same chagrin when the sonar and targeting laser temporarily malfunction during a late night bladder evacuation over the toilet with the bathroom light off. D'OH!!! That made a mess...   Oh, hey, that knock sensor I removed? It threads into a wet port. Who knew?! Learn something new every day. Put a pin in that chore, I'll fill it the rest of the way later.   The knock sensor arrived at about 1pm. I threaded it in, connected the wire, filled up the coolant, checked for leaks, and... drumroll.... fingers crossed for a perfect start, excellent timing, model fuel trims, and ...no squeaks... Here goes.....   No, it didn't start. At all. I cranked it a few times and it wasn't sounding good. Furthermore, I heard leaking again. Jesus H Tapdancing Christ, stop leaking all over the dang floor. This time I had accidentally overfilled the coolant reservoir and the churn of the water pump via cranking caused a bit to burp out. Ok, just, breathe... Put the flamethrower down. Dang thing wouldn't burn anyway, leaks too much...   Did you know the rotation of a round crank sensor in a round hole, matters? I do now. Took me about half hour to retrace steps and realize what I had done. Then it started right up.   No squeaks. The squeak was the old balancer.   Once it entered closed loop, fuel trims are dead on, hovering right around zero at idle. No more -30%. I'll credit the injector rebuild on that one.   Timing? I think there's an OBD 1.5 translation error with my Actron scanner. It's anywhere from -20 to -30 at idle, sometimes as high as -40 cruising. Sorry, the engine just isn't running that smoothly at -40 degrees ignition advance. It's just not. It's smooth all through the rev range and has decent power. I'm going to have to trust the seat of my pants on this one.   The new exhaust is very quiet. The old catalytic converter? Not melted, but definitely not healthy. Rains glitter when you turn it on its end...all the precious metal is flaking out. Once the new exhaust system burned in/smoked off a bit, the engine's exhaust smell is normal again. Not that I'd recommend going around huffing car exhaust, but, you know what I mean?   One problem to correct. The new exhaust has the opposite problem of the old spliced up exhaust. It wants to hit the floor where the old one wanted to rest on the cross member. Happy medium, please? Still noodling on that one, need to look at how I can adjust some hangers.   I don't know what's next. On one hand I want to run away from this thing as far and as fast as I can -- there have been a lot of NOT fun moments. On the other, now that it kinda drives nice, maybe drive it around for a little bit?   Shhh... it's not currently dripping oil all over the floor. I can see just a little wet at the bottom of the timing cover where it meets the oil pan seal. It's not dripping multiple drops with every ignition cycle, in fact, after some driving this evening it has yet to even form a drop that could drip off yet. But the weekend is young... I fully expect this could turn into Exxon Valdez by Sunday. Because this Blazer hates me. LOL.      
    • Grumpy Bear
      The Peckish Synapse

      By Grumpy Bear · Posted

      About that:   Once upon a time in a land far far away lived a car company that was shy about taking your money and wanted to be sure that they gave you more that you asked for so that you'd come back. No really, not a fairytale. 😱   But after the field got thinned out enough to limit the competition it seemed good enough to give you only what you asked for. Fair enough I say but in such a market you have to give something the others are not or they go to the one who does. Gimmicks or glitz. Oh, fins and chrome. Yea, shinny crow like cars. Yum.    Field narrows a bit more and 'brand loyalty' becomes a thing and the minute it does they start thinking to themselves, "Could we make more money if we gave them less than they expect and they will hang in there for brand and comfort with the known?" They gave it a try and da*n, it worked!!    Well, what if we teach them, groom them into believing that less is "Normal" and cut some more corners. Will that work? Oh heck yea!    🤔 I wonder, can we give then WAY less than they expect and make them mad enough to spit nails and STILL get them to pay up? Sure, if we get everyone else to do the same so that the choice is less or nothing at all. How would be do that? Platform sharing.  What a concept, right?  Steal like there is no tomorrow and it's legal too!    Truth is no one is going to give up driving, not for very long. The Gen Z crowd is fine with it and will be as long as someone not Gen Z will haul them around. At some point we all die.    Economic voting only works if you cast a NO vote now and again and enough of them to get dumb and dumber to wise up. Well, that's how I was taught anyway. And it should have worked. Would have worked. But the Bail out!!   Look, you have another choice if  you take that bag off your head. If the dumb it down to some predetermined expectation of how John Q Public will use it the, that is under design it to failure they you use it to a lower stress mode. D'ho!    A 1950 Royal Enfield Bullet 500 will go anywhere a Suzuki Hayabusa will and for just as long. But you will have to treat it for what it is and not for what you wish it was. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...