Window motor replacement

By B88i45
March 15, 2020 in Troubleshooting & Recalls

Recommended Posts

B88i45

Posted March 15, 2020

Can anyone point me to directions on how to replace just the window motor and not the entire regulator assembly. Trying to save a couple dollars and at several different online parts dealers they show in stock then unavailable when I check out. I have corrosion on the motor terminals. Pulled the door harness today, no cut wires were visible.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

Recently Browsing 0 members
- No registered users viewing this page.
Forum Statistics

250.4k
Total Topics

2.7m
Total Posts
Member Statistics

342,803
Total Members

8,960
Most Online

Newest Member
DroppingDiesel
Joined 16 hours ago
Who's Online 3 Members, 1 Anonymous, 826 Guests (See full list)

Latest Articles
- Got a “Service Door Latch” Alert? Fix It in a Minute
  Yesterday at 06:00 PM
- GM Recalls Cadillac VISTIQ Over Power-Folding Seats
  Wednesday at 04:35 PM
- Do-Not-Drive Recall Hits 2025-2026 GM Full-Size Vans
  Wednesday at 01:31 PM
- Every 2027 GMC Sierra Photo We Have So Far
  Monday at 06:50 PM
Posts
- Show Us Your 2019 & Up T1 Pictures !
  
  By Coastie05 · Posted 18 minutes ago
- Looking at ordering a '26 WT because I want a std cab, std bed
  
  By revmanii · Posted 2 hours ago
  
  Your truck lowered, looks good. I'm happy with the stance on this. I may need the extra ground clearance given my location/situation.
- PPE Transmission Pan Install
  
  By GMC4Zee · Posted 2 hours ago
  
  With this new pan, do you still use the same procedure to check the level? Its a deeper pan and our trucks do not have a fill tube/dipstick. So fill till fluid runs out the check plug?
- Looking at ordering a '26 WT because I want a std cab, std bed
  
  By Grumpy Bear · Posted 2 hours ago
  
  On mine? Yes. But I did it rather expensively. I had Deaver Springs make new rear springs with a 2" lower arch and then removed the nearly 2 inch thick spring to axle spacer. The front is Bell Tech 2" drop knuckles. Rear shocks, stock, were several inches over mid stroke so when I bought the King shocks I used the OEM length with the drop to put it at dead mid stroke. Fronts are King Coil Over OEM replacements with 600# springs. Again sits mid stroke. Deaver, King Suspension and Ben at Filthy Motorsports were all involved. Lots of measurements and lots of conferences but it came out spot on first time around. The 2" I link I sent you would use the factory shocks and coil overs or any other OEM type replacement units you like. I assumed from your thread that keeping the factory feel and ride quality was likely. My project intended to change the very nature of the beast and it did.
- Amsoil Price Increase
  
  By Black02Silverado · Posted 3 hours ago
  
  Yes back when all the stuff started in Iran. Had a small price increase, then another one. Supposedly temporary. But who really knows for sure as long as there is turmoil in the middle east.
GM-Trucks.com Clubs
- Black Truck Club
  
  Open Club · 612 members
- White Truck Club
  
  Open Club · 380 members
- Canadian Owners Club
  
  Open Club · 282 members
- Red Truck Club
  
  Open Club · 157 members
- diesel 3.0
  
  Open Club · 279 members
- Texas Owner's Group
  
  Open Club · 371 members
- NorthSky Blue Club
  
  Open Club · 118 members
- Midwest Owner's Group
  
  Open Club · 212 members
- 2015 Custom Sport Club
  
  Open Club · 5 members
- GM Snow Plowing Club HD
  
  Closed Club · 14 members
Popular Contributors
- Week
- Month
- Year
- All Time
1. 1
  
  Grumpy Bear
  24
2. 2
  
  Atlas
  14
3. 3
  
  Chuck FB
  12
4. 4
  
  revmanii
  11
5. 5
  
  newdude
  9
Show More