Jump to content

Inline speedo calibrator - Check Engine light

rainadog23
 Share

Recommended Posts

rainadog23 New Member

rainadog23

Posted
Posted

I have a 2019 Silverado RST with 6in lift with 35in nittos and have hypertech inline speedo. I have gone through 6 inline speedo's thinking they were the calibrators fault. I would be on cruise and it would malfunciton droping from 65 mph to 55 mph and jump back and forth. Once day it was parked and stared the engine and my check engine light came on along with low oil pressure. I had to take the inline speedo out to get it the truck to work properly. All this time I kept thinking it was the inline speedo but last night I came out to the truck and my parking brake was engaged. This happened to me twice yesterday and finally a check engine light came on. Ran the codes and got P0700 (Transmission Control System), P25A2, U0073 (Control Module Communication Bus A Off), U0101(Lost communication with Transmission control module) , U0129 (Lost communication with brake system control module), U2413, P25A2.

 

This morning I check and the check engine light is now off. I have 6500 miles but since 3000 miles some wacky things have been happening. Does anyone have any ideas? What do I tell the dealership if the check engine light is now off?

 

Thanks

  • 6 months later...
ict_wildcat Enthusiast

ict_wildcat

Posted
Posted

Did you ever get to the bottom of this?  I know it's been a while since you posted.  I'm running an inline speedo calibrator as well (rough country, not hypertech) and all has been fine until a CEL this morning with diagnostic code U0129.  Curious what you ended up doing.  Thanks!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.6k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,993
    Total Members
    8,960
    Most Online
    President Roberto
    Newest Member
    President Roberto
    Joined

  • Who's Online   0 Members, 0 Anonymous, 231 Guests (See full list)

    • There are no registered users currently online

  • Latest Articles

  • Posts

    • bwiese
      upgrading speakers on 2026 std cab WT...

      By bwiese · Posted

      I don't wanna do major surgery/upgrades, behind-the-dash work, add amps, change radio etc. on my '26 std cab WT. On the WT, it has the base 7" IOR infotainment setup, and only two speakers (doors). Since I listen to classical, looked around for speakers that do well and dug thru reviews. Two-way speakers were found to be better than 3-way. So I've ordered a pair of  Infinity Reference REF-9632IX 2 way speakers.  [These may  or may not have been discontinued / succeeded by the 3-way ...9633 ones.]    These speakers are lauded for 3 ohm and 94db sensitivity spec so they'll work well for ordinary base car radios without amps and offer better performance (quality,  strength) than  default base paper-cone speakers. They'll be installed in a few days and I'll let y'all know what I think. Bill W San Jose      
    • RyanbabZ71
      RyanbabZ71's 2019 High Country

      By RyanbabZ71 · Posted

      Thanks!   Changed out the rear shocks today to Bilstein 5100s.  So far feel much better. The stock Rancho were wore out.  Lots of heavy hauling (2 moves, home renovations, etc).  Next up is new BFG tires Monday.  Cant wait the current tires have little to no wet traction and are super loud (hum)    
    • Snowcamo
      No high speed fans...

      By Snowcamo · Posted

      Ok, I got the all the codes. What do you all think would be a place to start?
    • Chuck FB
      Correct way to service 2024 l8t allison trans?

      By Chuck FB · Posted

      How about I just point to the factory pans stand pipe little drain plug and claim its a pan with a real drain plug !. I just couldn't swallow the fact that a Dorman pan which at this point is probably the only pan out there that fits the gas version truck cost that much up here in Canada so I decided initially anyway to skip it and see what I thought of pulling the pan method and down the road if I felt inclined enough then I would either install a drain plug kit in the factory pan if there is enough room for it, or have a bung welded onto it, or put an aftermarket pan on. The thing is if the pan is not pulled then the magnets in the pan can't be inspected and cleaned or if wanting to change out the filter. However of course it certainly would make the job easier to be able to drop the oil first before having to handle the pan if dropping the pan that go around was the goal.    I knew a guy locally that was doing custom field spraying years ago with a pickup pulling a ground driven sprayer, I believe it was a GM pickup with an automatic trans. He had a drain plug in his pan and would drop the oil out of it once a week and top it back up through the dipstick tube to keep refreshing a portion of the oil often and that made the transmission last far longer than had he done nothing. Soft fields pulling 500 gallons of water at the start of each mixed up sprayer tank batch and in low range sucking along. I imagine he got some tips from other custom sprayer outfits doing the same thing at the time and learning from their blown up tranny mistakes. Transmissions then had no lock up converter so would cook the crap out of the fluid slipping that much and it would not have been synthetic fluid either. 
    • KARNUT
      Gas Prices

      By KARNUT · Posted

      3.39 Kroger’s in Montgomery Texas. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...