Jump to content

Wiring topper light access hole for wires in bed?

Jim larson1

By Jim larson1
in Troubleshooting & Recalls

Recommended Posts

Jim larson1 New Member

Jim larson1

Posted
Posted

Just getting around to running wires from underneath the car up to inside ARE topper.  I have wires up inside the tail light housing.  Just need to know how to get them to the inside of the bed so I can then connect to wires from 3rd brake/dome light.

 

is there a access hole or do I have to drill one?  Thanks

newdude Senior Enthusiast

newdude

Posted
Posted

GM has a designated terminal in the cargo lamp connector on the frame.  The center high mount lamps are known to leak on these trucks, so if you can avoid it, I'd use the wired circuits GM has.  

 

Quote

 

#PIT5314C: CHMSL Wiring for Aftermarket Bed Cap Topper

2016-2019 model years

Perform the following recommendations based on vehicle configuration:

  1. For vehicles built WITH Under Rail Bed Lighting Option:

    Trucks equipped with the under rail bed lighting option will already have the female side of the X400 connector.  Obtain an appropriate length of 18 ga wire to run from the X400 connector up to the CHMSL wiring for the cap or topper.  Use terminal part # 60012931 in AFL Tray 21, along with wire seal  part # 60994015 in AFL Tray 21 and connect it to one end of the wire.  Disconnect the X400 connector and remove the rubber cavity plug in pin position 4 and discard.  Install the terminated lead that was just made into the X400 connector pin 4.  Run the wire up to the CHMSL for the cap or topper and connect.  The ground for the cap or topper CHMSL will need to be made to an appropriate ground.

  2. For vehicles built WITHOUT Under Rail Bed Lighting Option:

    Trucks not equipped with the under rail bed lighting option will have a dummy X400 female connector, which will be removed and discarded.  The female side of the X400 connector is not available separately, but can be obtained by ordering the under rail bed lighting harness GM part number 23327843.  The harness will come with terminals/wiring in pin positions 1 and 6.  Remove the wiring and terminal from pin location 1 and discard.  Move the rubber cavity plug from pin position 4 and reinstall it into pin position 1.  Obtain an appropriate length of 18 ga wire to run from the X400 up to the CHMSL wiring for the cap or topper.  Use terminal part # 60012931 in AFL Tray 21, along with wire seal part #  60994015 in AFL Tray 21 and connect it to one end of the wire.  Install the terminated lead that was just made into the X400 connector pin location 4.  Pin 6 is a ground circuit that is used for the under rail bed lighting and it can also be used to ground the CHMSL for the cap or topper if the wire gauge size in the connector is of the proper size for the CHMSL in the cap or topper.  If the wire gauge size is too small, any of the following can be done:

  • Make a second wire as described above.  Then, remove the wiring from pin 6 and discard.  Install the new terminated wire in position 6 for the ground and run it up to the CHMSL for the cap or topper and connect.
  • Remove the wire and terminal from pin 6 and install a rubber cavity plug.
  • Cut the wire for terminal 6, leaving a couple inches of wire, and seal the end of the wire.

Note: The terminal removal tool for the female side of the X400 connector is J-38125-212.

2014-2015 model years

Perform the following recommendations based on vehicle configuration:

  1.  For vehicles built WITH Under Rail Bed Lighting Option:

    Trucks equipped with the under rail bed lighting option will already have an X6 connector at the rear body junction block X63A, which will be removed and discarded.   Obtain an appropriate length of 14 ga wire to run from the rear body junction block up to the CHMSL wiring for the cap or topper.  Use terminal part # 1-968857-3 in Lear Tray 7, along with wire seal  part # 828905-1 in Lear Tray 16 and connect to one end of the wire.  Disconnect the X6 connector at the Rear Body Junction Block and remove the rubber cavity plug in terminal position 1 and discard. Install the terminated lead you just made into the X6 connector terminal 1.  Run the wire up to the CHMSL for the cap or topper and connect.  The ground for the cap or topper CHMSL will need to be made to an appropriate ground.

  2. For vehicles built WITHOUT Under Rail Bed Lighting Option:

    Trucks not equipped with the under rail bed lighting option will have a dummy connector at the X6 position of the rear body junction block. The X6 connector body is not available separately, but can be obtained by ordering the under rail bed lighting harness GM part number 22878806. The harness will come with terminals/wiring in positions 4 and 7. You will need to remove the wiring from terminal 4 and discard. Move the rubber cavity plug from terminal position 1 into terminal position 4.  Obtain an appropriate length of 14 ga wire to run from the rear body junction block up to the CHMSL wiring for the cap or topper.  Use terminal part # 1-968857-3 in Lear Tray 7, along with wire seal  part # 828905-1 in Lear Tray 16  and connect to one end of the wire. Install the terminated lead you just made into the X6 connector terminal 1. Terminal 7 is a ground circuit used for the under rail bed lighting and it can be used to ground the CHMSL for the cap or topper, if desired.  If terminal 7 is not used remove the terminal and install a rubber cavity plug or cut off the additional wiring, leaving a couple inches of wire and seal the end of the wire.

 

  1.  

Jim larson1 New Member

Jim larson1

Posted
  • Author
Posted

That’s the circuit I am using.  Wire is strung from that connector for th3rd brake light into the area behind the tail light.  I just need to know how to get it up and through the box to the interior of the pickup bed?

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      Can it still be Assembled I?    Stribeck says that we need a certain amount of viscosity under conditions of load and velocity to prevent two surfaces of a know roughness from tearing each other asunder. And we have marketing trying to tell the masses that those two surfaced require less of that commodity due to more exact limits being placed on the same old clearances. We also know that there are limits to how hard something can before it becomes to brittle to be viable and to smooth to 'wet' the surface and that both of those conditions have been known and met since about the Second World War.    That viscosity value shook out at 10 centistokes at 212 F just under a hundred years ago.  Give this a look: [Anton Parr]     What is advertised is the Kinematic viscosity (mm2/s) or that which has been density adjusted but the value we are after is the dynamic viscosity (mPa.s) or true viscosity. You can see that this number is dependent on density thus base stock and temperature. You can also see that an SAE 30 doesn't reach that value in this example. However an SAE 30 that is at the upper end of the SAE 30 range; 12.5 cSt (mm2/s), might. 12.5 * .83 = 10.375 (mm2/s). If you could find an SAE 30 at the upper end these days.   Then there is the complication of viscosity modifiers or VII or VM, whatever you wish to call them. Polymers added to very thin base oils, perhaps 3 to 6 cP oils, that will meet the SAE *W30 spec at 'tested' shear rates and 100 C/212F  target temperature. So a polymer fortified base that is a fraction of the 10 cP requirement Stribeck insist upon.   This could be all well and good if those polymers didn't have two very problematic 'features'. They shear or loose viscosity both 1.) permanently and 2.) temporality. And they do both omitted in the advertised data with the distinct  purpose of deceiving the consumer of the actual operating state of the fluid. I've shown the example of Warren Oils COSTCO 10.91 cSt 5W30 formuation several times where the 100 C HTHS value is 6.9 cP!! That's the temporary shear down and with and SSI or shear stability index of 9.4 cSt. Note the intentional deception in using mixed units?    After a short while that 9.4 cSt oil has a viscosity corrected dynamic value of 7.8 cP. But as the SSI is still within the range of an SAE *W30 whose lower value is 9.3 cSt.    This allows them to continue to call this SAE 16 weight oil a 30 weight, the cake, and still meet the API requirements for fuel efficiency IMPROVEMENT mandated by the EPA. The eating of the cake. By the time you've worn out your motor doing the responsible thing by adhering to the warranty requirements, (the stick), you get deprived of the carrot, wear control. So sad, to bad.   So what can be done? Do I need actually say? [Anton Parr]       Even this must be monitored if the oil is on the low side and the VII an organic or you opt for a 0W40 with an even lighter base oil and more / higher MW VII. (Note the lower density of the 40 weight versus the SAE 30 mono-weight?)    There is another workaround. Temperature. An SAE *W30 run at a bulk temperature of between 180 and 195 F.    Being the belt and suspenders sort I am I do both. Run it cook and run it heavy.    In Part II I'll work the AW package. 
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      So, do I go elbow-deep on this thing or list it for sale and play dumb? Seems to "runs good."   I'm about $1200 away from having: -a rebuilt injector ($300) -a new cat ($250) -a new cat back exhaust (OE style) ($300) -a new AC compressor ($200) -AC refrigerant charge ($150)   In theory, this should rectify the obvious detracting issues from its value and operability. Cold AC with a non-squeaking AC pulley both sounds and feels good. An exhaust that isn't cut/hacked in 17 different places and doesn't vibrate on a crossmember would make it sound and feel less janky. A working cat would help the stink, and will save the earth, but *if and only if* the fuel system is working properly, which would also address the intermittent "rich" CEL.   Heard a good one... CEL for "Rich condition" means you haven't spent enough money on the truck lately, and it's letting you know.   Rebuilding the injector would seem to be the most important part. Replacing the cat would be secondary. I don't think mine is plugged or overly restricted, but it might be a little restricted? I have no good way to tell other than seat of the pants feel. I hate the smell.   The current theory is I have a rich idle problem: A bad fuel pressure regulator, or a leaking injector(s) being the highest probabilities. I already replaced the FPR but that doesn't mean its replacement isn't also bad. It was a new part from Dorman, but the packaging looked like it had been sitting on a shelf for 20 years.   This is the (single) upstream O2 sensor shown at idle. I'm getting a lot of "rich" it seems. Sometimes it stays high like that and doesn't drop down. That makes me think it's processing injector leaks or a partially stuck open injector.     Other times it looks like this. Nice oscillations between rich and lean, which is what I think it should be. Under load and at speed, the oscillations are nice and tight and uniform looking, high and low.     Fuel trims suggest the PCM is compensating pretty hard at idle to pull fuel out. But it's not enough to trip a CEL. Something about slowing to a stop: brake vaccum booster, EGR, or the EVAP purge is delayed, or there's pooled fuel in the intake again that's draining into a cylinder is enough to set the CEL. Of course, in two days of driving, it hasn't set. I was hoping to actually look at the freeze-frame data when it sets. IAT is high because it's idling on an 83 degree day here.  
    • Another JR
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By Another JR · Posted

      Have considered installing a DC to DC charger in your camper to replace your isolator?  
    • newdude
      Gas fill door

      By newdude · Posted

      Common failure.  You need to replace the fuel door housing.   The painted cover transfers over to the new housing.  To remove the old one there is 4 spots where you poke the plastic to release it.  
    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...