Jump to content

Recommended Posts

Posted (edited)

I am looking to change the tail pipe tips and thought about eliminating the resonators. I don't want to change the whole exhaust system. I had done that before on a 2017 and hated that helicopter sound when the motor cut off cylinders.

Has anyone just removed the resonators? Was there much difference in sound?

 

Edited by bikersully
  • 2 months later...
Posted

Not sure what year you have. My 2020 has screens instead of an actual resonator. When i did a muffler delete i got the helicopter sound pretty bad even though i left the screens alone. I bought the range device to keep it from dropping. That is really the only thing to do if you are not doing an exhaust. Not sure how it would sound if you just removed the screens and left the muffler.

  • 3 weeks later...
Posted

From what I've read elsewhere, the helicoptering noise doesn't occur (or at least is severely reduced) if you leave the flapper value on when you do a muffler delete.  But that is all third hand here-say as my 2022 isn't due to be delivered until later this week.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,962
    Total Members
    8,960
    Most Online
    contrabombarde
    Newest Member
    contrabombarde
    Joined
  • Who's Online   1 Member, 0 Anonymous, 827 Guests (See full list)

  • Latest Articles

  • Posts

    • From where I'm sitting this sounds like a compatibility problem. I'm assuming the 2007 was a 900-series truck, and not an 800-series (they were sold side-by-side in dealerships that model year), since it starts and runs.   This is why I HATE post-2006 vehicles. Everything becomes a huge problem when you try to keep the thing running for longer than the manufacturer has designed it to.    I can't remember when Global-A architecture started - either '10 or '11. For your sake, you had better hope it's '11, or you're going to be spending some BIG money to correct this cluster-eff. That's something you need to find out before doing anything else. You may have several computers bricked ... but the fact that it runs tells me you MIGHT be ok here.     EDIT: Just did a quick refresher. You're screwed. This is Global-A. The 2 systems are NOT compatible in the slightest. Once you get the correct engine in there that IS compatible, you're going to need to see how many computers are locked. Absolute NIGHTMARE to straighten out, too. Your buddy might be better off cutting his losses and finding something else.   Welcome to post-2006 vehicle electronics. This is why I quit the industry, and drive nothing built after 1994. This stuff takes all the fun out of wrenching!  
    • Recently acquired new 2026 Silv. 1500 WT  - L3B + 4WD,  std cab + std bed, in (duh!) Sierra White. Upgrades: replaced 'steelies' w/  Vision "Flow" black alloys,  17x8.5"; HDX nerf bar w/steps (black powdercoat); Weatherguard large/deep alloy saddle toolbox; Michelin fitted bedmat (sale, perfect fit) Weathertech door sill guards TBD: rear wheebox liners 4x black fender arch trim - searching for best  (Putco: chrome only; not looking for flares either!) -Bill    
    • True, hard to say what differences there may or may not be between Chev and GM as well as a production year or mid year part change either.    I just found it odd that under the Sierra choice on the Autel that many of the last few years of production year did not include the choice of changing the tire pressure but if that is an Autel thing or a GM thing as to why the choices were not there. Knowing what tpms sensors are on the truck should give some guidance into which choices on the tool even make sense to try as I wouldn't give up just yet with the tool but I guess he will see what if anything he comes up with if he finds out a bit more info and tries a few more things on the Autel. 
    • I'm sure if you went to a junkyard where you go in and pull the part off the truck yourself, not a used part place where they do it for you, you can get that part on it's own.  Depending on if and what else you would be buying, and time of day, they might even just skip over adding it as a item to the bill.
    • No, we trade them like pokeman cards.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...