Jump to content

Electrical gremlins

Blue924.9
 Share

Recommended Posts

Blue924.9 New Member

Blue924.9

Posted
Posted

Hello new member here. Picked up a 03 gmc 2500hd 4x4 with the 8.1 and the Allison this summer with 140k no rust which is rare up north. Drove it a couple times this summer with no issues and then this winter I started having battery drain issues. Checked for drain with a meter but did not have anything only 33 milliamperes. Put a maintainer on the truck with a new battery as the old one had been drained enough to cause it to go bad. The battery drain was enough to trip a code on the maintainer which happens over 1 amp.

 

 I’m currently having issues with the hvac module the truck has dual zone auto hvac. while the battery was going dead the hvac was stuck at 75 with no fan I later figured out that was a calibration procedure. Once the calibration would complete the hvac would work as normal at this point the new battery and maintainer are on I unplug and plug it in to charge up to 2 amps for 12 hours to at least keep the battery from going dead. Thinking the hvac is fixed I go to use the truck about a week later and the hvac is stuck on 71 none of the buttons on the hvac work or respond to inputs and the fan says it’s on but is not. Didn’t have time to mess with it and used a different vehicle. That night the error code is not on the maintainer like it was every night for the last two weeks. Left the maintainer for a week and it never tripped the excessive drain code.  Went to try the truck this morning and hvac module still stuck on 71 with no response. The module does seem to be replaced by previous owners as the color doesn’t seem to match the other pieces of the interior and there is virtually no wear on the buttons. I pulled before the battery was replaced after driving the truck which I will attach to the post. All the other functions seem to work like radio and dash with the exception of the gear display which washes out after 15 or so minutes of driving. The other functions working make me think the bcm is not faulty

9324064B-8C98-43B6-990D-61881DA68494.jpeg

David89GMC Enthusiast

David89GMC

Posted
Posted

If the auto hvac unit didn't come with the truck, what did? Look at your option codes in the glovebox and verify it was originally manual or auto.

Keep in mind that cheap accessory units can fail very quickly, best to get a used OEM unit than a a new one made in China. And stay away from Dorman if you can. And get the exact replacement unit if you know the original number. There are many different units that will may not be compatible with the system controller.

Good luck.

Blue924.9 New Member

Blue924.9

Posted
  • Author
Posted
9 hours ago, David89GMC said:

If the auto hvac unit didn't come with the truck, what did? Look at your option codes in the glovebox and verify it was originally manual or auto.

Keep in mind that cheap accessory units can fail very quickly, best to get a used OEM unit than a a new one made in China. And stay away from Dorman if you can. And get the exact replacement unit if you know the original number. There are many different units that will may not be compatible with the system controller.

Good luck.


is there a list somewhere of the option codes? It’s a well optioned truck so I would guess it was automatic, is it Possible to switch it to a manual or vice versa hvac?

 

 I’m saying it appears to have had the oem hvac module replaced with an aftermarket one due to things not quite matching up

davester Senior Enthusiast

davester

Posted
Posted
16 hours ago, Blue924.9 said:


is there a list somewhere of the option codes? It’s a well optioned truck so I would guess it was automatic, is it Possible to switch it to a manual or vice versa hvac?

 

 I’m saying it appears to have had the oem hvac module replaced with an aftermarket one due to things not quite matching up

In the glovebox, there's a sticker with a table of 3-character alphanumeric codes, which describe the options your truck came with.  The best source for getting what most of the codes mean (some are internal gm codes that don't have a public description) is the full service manual for that year, but there are online sources that are pretty good.  Google "RPO codes" for sites that have lists of what the various codes mean.

 

It's useful to keep those codes handy for ordering parts as well, as they will help select the correct parts for your vehicle, based on it's options.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Grumpy Bear
      Sugar Bears 2015 GMC Terrain SLE-2 2.4 AWD

      By Grumpy Bear · Posted

      287,500 Mile Service   8/13/2026   Reset Fuel Trims   Since the work done in the previous post there was a good improvement in response in all areas except right after a fill up where the LTFT would go -20%+ for about four miles while the STFT was near neutral. Before the work they both went very negative for a few miles after a fill up but act normal thereafter.    We did a systems check of the vapor recovery system for functionality and ability to hold a vacuum. That checked out fine. But this doesn't mean the charcoal canister is dead in the water. Testing that is next up. For now the reset of the fuel trims.    I intentionally shorted the fill exactly two gallons to eliminate any chance of filling the canister. On start up the trims were behaving normally until I got up and rolling where the LTFT went -10 / -11%% but the short was + 2 to 0%. Within a mile the the STFT offset the LTFT and by 2 miles they were neutral. HUGE improvement but still not hunky-dory.    I'll watch them for a few days. Perhaps another tank where I will fill completely to 'first click' and compare. Meanwhile on the hunt for a new canister and I'll toss another purge value at it for good measure. Pending the outcome of the canister test that is. Progress of any kind is welcome.    Fuel economy improvement with bringing hole #3 back to the living was a noticeable bump to the positive. Even on the few miles I drove after the refill I already see another bump up by the trims reset.     She's purring like a kitten with a warm bowl of milk.    BTW, adding 50 rpm to the idle took the majority of the negative timing out on cold start up and leaned the cold idle. No longer burbles in the cat. What a dumb way to heat a cat.      
    • OnTheReel
      Post your UOA, (used oil analysis) here

      By OnTheReel · Posted

      Yeah, shame I can’t really get that filter easily anymore. Running a PureOne. Your fave!    TAN would be neat to see. Confirmation I ran it too long probably. 🤣
    • superdave160
      Roll up bed cover experiences

      By superdave160 · Posted

      My son and I both bought new trucks in 2017. Both of us immediately put Truck Covers USA American Roll Covers on our trucks. My son still has his truck and it never sees the inside of a garage. We live in Alabama, so not much snow. My truck was my daily driver and was in the garage when I wasn't driving it or at work. No issues with either cover even after almost 9 years. About a year ago I sold my truck to my brother and bought a 2025 Silverado 2500. The second thing that I put on that truck was a new Truck Covers USA cover. They are very well made and have a very positive locking system. I looked at a Retrax and my concern was the way that the cover locked to the rail. BTW, the first thing I put on the new truck was step bars. Those new trucks are high!
    • superdave160
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By superdave160 · Posted

      The Allison 10 speed torque converter doesn't "lock up" like the previous transmissions. It has 4 operational modes; open, slip, transition from open to slip; transition from slip to open. I have an Edge CTS3 monitor and I monitor transmission torque converter slip. Step on the gas and you get a little slip. Take your foot off the gas and you get a little negative slip. I have not found a way to display the torque converter mode beyond that. My Edge CTS3 also displays something that our trucks should already display, the current gear. I also monitor throttle body position and engine load. If I see the engine load getting too high, I'll manually drop a gear.
    • Grumpy Bear
      Post your UOA, (used oil analysis) here

      By Grumpy Bear · Posted

      Nice result. Your filter is working well  I'd have like to have seen the acid number for this sample. Curious type that I am. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...