Jump to content

flowmaster BAD worth changing??

lousieg55

Recommended Posts

lousieg55 Enthusiast

lousieg55

Posted
Posted

hey guys ok so i got a question for all you want your opions and everything. So i have 2002 gmc sierra with the 5.3 i have daul exhaust with 3 inch piping going with a flowmaster muffler i always hear how bad they are i did not notice anything bad about it sounds ncie a little faster but what is soo bad about flowmaster and is it really worth the hundred bucks or so to switch to magnoflo or something

Meatywand Enthusiast

Meatywand

Posted
Posted

sometimes they drone really bad in the cab, and it gets annoying really fast. And they also steal HP, but with a 4x4 truck I don't think thats really going to matter. If you already have it and like it...keep it, but if you were building a new exhaust I would tell you to avoid Dronemaster

bluntlunchbox Enthusiast

bluntlunchbox

Posted
Posted
sometimes they drone really bad in the cab, and it gets annoying really fast. And they also steal HP, but with a 4x4 truck I don't think thats really going to matter. If you already have it and like it...keep it, but if you were building a new exhaust I would tell you to avoid Dronemaster

 

 

 

 

I'm looking to u/g the exhaust on my 06' ecsb Sierra and was totally sold on Flowmaster 50 series "delta flow" becuase they specifically talk about reduced cabin noise. I can deal with the slight drone, but has anyone actually dyno'd any of these mufflers?

lousieg55 Enthusiast

lousieg55

Posted
  • Author
Posted

hmm no they dont drone no more they changed that i dont really think flow master rob horspeower any more thats what every one sence but they are smaller so dont see how they could just seeing what people would say about changing or what ever

 

And i want a little more hp haha

99Silver6.0 Senior Enthusiast

99Silver6.0

Posted
Posted

Chokemasters suck. They really do. When I first got my truck... I acutally paid to get some put on.... 1 month and I hacked the s**t off. My low end went bye-bye. Went to a single 3" with a Borla XR1 and like magic, my truck wasnt a TURD on the bottom end anymore.

 

Do a search on LS1Tech and PerformanceTrucks.net. Youll see how many people love to hate Flowmaster.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,840
    Total Members
    8,960
    Most Online
    appletrav
    Newest Member
    appletrav
    Joined

  • Who's Online   0 Members, 0 Anonymous, 407 Guests (See full list)

    • There are no registered users currently online

  • Latest Articles

  • Posts

    • newdude
      2 speed transfer case optional now?

      By newdude · Posted

      This is a 1/2 ton thing ONLY.  All HDs 2020-2026 have the two speed transfer case, with Autotrac as an option.     1/2 tons 2019-2026, regular 4x4s come with a single speed case (no 4LO!), and trucks with Z71 ordered, or all Trail Boss trucks come with the 2 speed case.  2 speed case is also an option on WT, and is also standard on High Country.  
    • newdude
      Different requirements for oil filters?

      By newdude · Posted

      2013 5.3 still to this day calls for the PF48 filter.  Which as a 15psi bypass pressure.     There is a TSB, 17-NA-157 that talks about the PF-63 and PF-64 filters which have a higher bypass rating of 22psi.    TSB HERE - temp.xml   "Beginning in 2012, the oil pumps began to regulate main gallery feedback instead of pump out pressure. This means that the oil pump now does not begin to regulate until pressure is built up to the main gallery. This change reduces the amount of time it takes to provide oil to the engine bearing and lifters during extreme cold start conditions.  Main gallery feedback oil pump control systems are present on the following engine families which use Spin-on oil filters: Small Gas Engine (SGE), Large Gas Engine (LGE), High Feature (HFV6) Gen2 and Small Block Gen5 gasoline engines. These engines with the main gallery feedback oil pump control systems are factory built with an ACDelco® oil filters"   It also calls out what engines use those filters.  The gen 4 small blocks were not on that list (LMG, LC9, L9H, L92, L94, L20, L96).  Gen 5 small blocks use the higher pressure filter.          That all said...   Your 7045 Napa filter is the PF63 equivalent, with 22psi bypass.  You are already using the higher bypass pressure filter.  You CAN keep using it, you don't technically have to use it though.  
    • Grumpy Bear
      Different requirements for oil filters?

      By Grumpy Bear · Posted

      Do you know WHY the filter relief setting was increased to 22 psig?    When the new system goes into the second stage the pump volume ramps up considerably. It was found that the 15 psi filter bypass setting put the filter in bypass on a warm engine when the second stage was activated. Raising the filter bypass setting forced the filter to do what it designed to do. Filter. Preventing debris from circulating during high load, high rpm operation.    So next question is how did GM find this out? VLOM/lifter failures and a deep dive by Melling Corp.    Last question. Is it required? Look at it like this; a motor may be equipped with a rev limiter. But it only works if the set point in reached. That 22 psig setting only matters if the pressure differential across the filter media exceeds 15 psig during normal warm operation. Second stage kicks in around 3000-3500 rpm.    I can't answer your question because I don't know you and how you use the truck. But I think there is enough information here to let you decide for yourself. 😉
    • Coastie05
      give me some tips to make my truck look better

      By Coastie05 · Posted

      Go back to OEM wheels. 
    • newdude
      2020 Trailboss 6.2 replacement

      By newdude · Posted

      Probably not their first rodeo, so it should go as planned most likely.  Typically the service manager or tech doing the swap will put some seat time to shake it down after they get it all put back together.  We usually put 50-100mi before we hand them back so if something happens, its not after you get it.  A coolant leaks, oil leaks, a ground left off or loose, vibration, etc.     The new engines so far have been good?  There's been a couple that have popped out there again (the replacement engine) but most have been okay.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...