Jump to content

silveradosid

Member
  • Posts

    2,688
  • Joined

  • Last visited

  • Days Won

    2

Everything posted by silveradosid

  1. just replaced my 2014 grill with z 71 grill. i still have the old grill i will check to see if the inserts are removable today
  2. contact Harlech and ask him about the vcx nano . he shows it can do steering reset maybe it can do the tranny also
  3. my 2014 came with a steel driveshaft and it had 28 thou run out replaced it and rumble strip feeling is almost gone 100 percent
  4. another note do not use this program on 64 bit windows, you may get lucky but i had a problem with the canny 7 staying connected works fine on 32 bit windows
  5. thanks for all your help glad to hear your on the way of recovery i also got a defective power board and am waiting for another. to bad about the cab mounts but that is another story
  6. thanks Kyle guess i can scratch that fix off of my list lol
  7. could be the bearing for the a/c compressor
  8. my 2014 the chime starts when i open the door as if the key was in the ignition but it is in my hand i put the key in and it stops and some mornings i go out to the truck and the chime is going off and the truck is still locked
  9. you can try and pm harlech, but i think he is in recovery mode hope he is ok
  10. it will fit .even the frame bolts are in the same locations. but if you have sensors in your bumper they are a different size and plug you will have to trim the rear lower corners of the box to allow clearance of the steps. i put one on a 2007 nbs and you cant see where i trimmed out the box
  11. two things come to mind one is has any one checked to see if the vent is plugged and two is did the rebuild shop put a new yoke in. alot of rebuilders like to use what is called a ready sleeve on old yokes. it is a sleeve that is pressed on the old yoke to give the seal a smooth surface to ride on. because the sleeve is a larger diameter it stretches the seal or cuts the edge of the seal and always end up leaking. i own a transport company and have had this problem with the rebuilder i have been using for 30 years. i dont care of the cost they now know to put a new yoke on
  12. it is because the led bulb has a shorting diode in it and all the tail lights share a common ground you are getting feed back from the led bulb
  13. if your pic is correct then my bump stop is upside down how could they do this right from the factory guess i have to disassemble again thx
  14. i installed 5100's on the front yesterday and when disassembling them that bump stop on the shock was the opposite way you have yours in the picture is it installed wrong
  15. could be intake gasket try spraying either or water and see if it changes
  16. thx might explain why my 2014 flex is getting such bad fuel mileage i will check to see if my scanner has that option of reset
  17. does this wonderful gm engineering trigger the service engine light
  18. maybe the trucks should stay in mexico where they are built lol no cold weather
  19. was searching canadian gm parts suppliers and their sites say no longer available, went to the dealership and that part number is correct, they had it in stock so i bought it 200 cdn dollars, thanks again for the write up on how to do this
  20. do you know of another part number for the pump when i did a search it come up no longer available great write up
  21. i would be more worried about what blew that fuse, did you boost some one it takes a serious short circuit to blow that fuse. even buying the replacement part it might blow again
  22. do 1.5 lift alignment and adjust headlight no worries
  23. thx tbarn
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,917
    Total Members
    8,960
    Most Online
    1981dustin
    Newest Member
    1981dustin
    Joined
  • Who's Online   1 Member, 0 Anonymous, 1,264 Guests (See full list)

×
×
  • Create New...