caskey_b

have a part number?

Opt7 has a y splitter that plugs into the 4way on trailer

glad i found this thread and now know that I am not the only one experiencing this... purchased a BRAND NEW set of OEM projectors to install on my LT and had the same thing happen after a decent rain, and a decent temp change.... Ill be going with the moisture packet deal if it continues to be an issue

i have my own... ill give her another shot... now that i have it painted... maybe itll look better since the paint is covering the outer edge... thanks

see... i tried vinyl first... didnt like it... vinyl wouldn't conform down into the gaps around the perimeter of the bowtie... and could always see gold

what did you use on the steering wheel bowtie? i just did mine as well (with plastidip) not 100% satisfied with it so may do it again

I just did the bowties on my wheels as well... i used vinyl and then sprayed a couple coats of clear over the caps...

got the front bowtie done and put back on... i have masked off the wheel center caps and doing those in black too... next will be the bowtie on the steering wheel... after that, all gold bowties will be BLACK!!!! if i could only change the programming on the computer to have the one on the dash and radio be black..... .pgamboa??? thoughts? hahaha... kidding

not sure who makes it... but with dry filters... i just check them periodically... every 7500-10000 miles usually... you can literally just tap them clean... or if a little dirtier, rinse them (opposite of airflow) and let air dry.. really depends on the roads you drive... i live on gravel, so i typically clean them every 10k or so... some may not need it til 15 or 20k

front is getting cleared now

was going to paint... but didnt want to ruin them if it didnt turn out... if this doesnt hold ill remove and paint

I did... I used about 7-8 coats of plastidip.... (nothing too heavy on the coats)... then about 4-5 coats of clear enamel

let me know if those fit in the projectors AND you can get the dust cap back on... Ive been eyeing those but dont want to spend $100+ and HOPE they work

they do look 100% better than the reflectors... JUST installed them and haven't been out at night yet... a little bummed as my Opt7 LEDs will not fit in the low beam (due to the projector taking up too much room) so ill be running halogens for now.... but i was actually quite impressed with my stock reflector's light output.... I can only hope/imagine these will be better... Got them from a member here actually..

installed OEM projectors on my LT front bowtie off being painted....

got the rear bowtie painted and put back on...

I just put the FluxBeam X in my low beams (H11).... very impressed so far!!! ZERO light scatter and I have halogen reflectors I had the Opt7 Canbus on my 14 Silverado... had some intermittent issues with only 1 light firing on the low beams (it is a set i have been using for about a year on another vehicle... so could be ballasts/relay going bad)... great light output from them though..... low beams (Opt7 Canbus 5000k) high/low beams (both Opt7 Canbus 5000k) both low beam pics are from exact same location... so you can compare HID vs LED

Added tint to my fogs today... need to test them out at night soon....

2014 Silverado with 8" MyLink... going down interstate yesterday... screen blacks out (radio still playing) then comes back on after 5 seconds.. radio never stopped, all presets stayed... scared me for a second though... definitely weird...

can you explain more on this? wired open the Exhaust Adapter Valve?

look under your seat from the driver side footwell... put a piece of rubber (mine cut from rubber hose) and a hose clamp TIGHT to each side where the white "dodad gadget" is... seat fixed!!!

2014 Silverado.... fuse #39 "Misc Ign" 10amp under the hood this pic looking at fuse box standing by left front tire

wouldnt mind checking mine as well... is there a "how to" on pulling the dash apart to check?

output and pattern of the HI/LOW HIDs is great... i am having some random issues of one low beam not firing on every once in awhile.. sometimes pass side.. sometimes driver side... BRAND NEW BULBS... harness and capacitors hooked up... the ballasts, harness and capacitors are pushing 2 years old... not sure if thats the reason or not... but i have the new Opt7 FluxBeam X LEDs that will be at my door tomorrow that I am going to try in the low beams and see how they are there is a 10amp misc ignition fuse under hood... cant remember off top of my head... but i will try to get a pic of it ... PM me if you are interested and ill send the pic directly to you

check post #606 i did it a different way than most requires minimal wiring.. but now my fogs are DRLs