Jump to content

Denali Bucket Seats And Console

bugmenot

Recommended Posts

bugmenot Enthusiast

bugmenot

Posted
Posted

I have a 2007 with the black lint collector seats and the jump seat. I can get 2008 Denali black leather buckets front and rear but no the third bench and the console that have been in storage for almost 2 years from a total loss Yukon. Should I get them ? How much should I pay for them ? Is $1000.00 too much ?

nickvrebel Senior Enthusiast

nickvrebel

Posted
Posted

the biggest problem would probably be providing power to the power adjustments of the seats - but as far as bolting right in, it will work.

bugmenot Enthusiast

bugmenot

Posted
  • Author
Posted

Yes NickV it looks like you are right about the wiring problem. I want the console more than the seats but I have to take the seats to get it. I think I would just swap out the seat cushions and backs and leave my stock seat tracks and wiring in place. I have seen these same four leather buckets and console listed on E-Bay for over $2200.00 so if I can get these for just under a grand would that be a good deal or not ?

bugmenot Enthusiast

bugmenot

Posted
  • Author
Posted

I purchased the four black leather buckets and the console from the guy for $984.99 no taxes no shipping charges. They look like they are brand new. I just have put them in the truck. The back bucket seats will take some extra work to get them in. The two rear bolt holes in the bottom brackets are not right but a little cutting, drilling and welding will fix that. They are going to look great in my truck.I think it may be the only one around with rear bucket seats ?

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • PhilB
      No 12v outlets in 2026 gmc Sierra

      By PhilB · Posted

      It is possible to add your own 12v outlet to your truck.  Check out this video:   I verified via GM Upfitters that pin 31 is the same on the 1500 trucks.  The wire is GM part number 84779405.   You can get the GM 12v outlet from Amazon  https://www.amazon.com/Genuine-Accessory-Receptacle-25774623-13549530/dp/B0F1H9YRGF EWAY 12 Volt Power Adapter for GM   https://www.amazon.com/EWAY-Chevrolet-Silverado-Cigarette-Ignition/dp/B0915RRW6Q/ref=sr_1_1?   I just haven't figured out a good place to put the 12v outlet in my truck.   Some people are getting USB-C to 12V adapters  https://www.amazon.com/WYMECT-Cigarette-Lighter-Socket-Adapter/dp/B0F87WNQKB/ref=sr_1_1_sspa? Not sure if they provide the correct amperage that a device like a tire inflator would need.  
    • Core-Lokt
      Wiring Help, Please

      By Core-Lokt · Posted

      Thanks; I looked there a few minutes, and I think I can find something. I really never looked there, as I thought it was stuff like PTO/aftermarket bodies/accessories like snow plows.
    • newdude
      2 speed transfer case optional now?

      By newdude · Posted

      This is a 1/2 ton thing ONLY.  All HDs 2020-2026 have the two speed transfer case, with Autotrac as an option.     1/2 tons 2019-2026, regular 4x4s come with a single speed case (no 4LO!), and trucks with Z71 ordered, or all Trail Boss trucks come with the 2 speed case.  2 speed case is also an option on WT, and is also standard on High Country.  
    • newdude
      Different requirements for oil filters?

      By newdude · Posted

      2013 5.3 still to this day calls for the PF48 filter.  Which as a 15psi bypass pressure.     There is a TSB, 17-NA-157 that talks about the PF-63 and PF-64 filters which have a higher bypass rating of 22psi.    TSB HERE - temp.xml   "Beginning in 2012, the oil pumps began to regulate main gallery feedback instead of pump out pressure. This means that the oil pump now does not begin to regulate until pressure is built up to the main gallery. This change reduces the amount of time it takes to provide oil to the engine bearing and lifters during extreme cold start conditions.  Main gallery feedback oil pump control systems are present on the following engine families which use Spin-on oil filters: Small Gas Engine (SGE), Large Gas Engine (LGE), High Feature (HFV6) Gen2 and Small Block Gen5 gasoline engines. These engines with the main gallery feedback oil pump control systems are factory built with an ACDelco® oil filters"   It also calls out what engines use those filters.  The gen 4 small blocks were not on that list (LMG, LC9, L9H, L92, L94, L20, L96).  Gen 5 small blocks use the higher pressure filter.          That all said...   Your 7045 Napa filter is the PF63 equivalent, with 22psi bypass.  You are already using the higher bypass pressure filter.  You CAN keep using it, you don't technically have to use it though.  
    • Grumpy Bear
      Different requirements for oil filters?

      By Grumpy Bear · Posted

      Do you know WHY the filter relief setting was increased to 22 psig?    When the new system goes into the second stage the pump volume ramps up considerably. It was found that the 15 psi filter bypass setting put the filter in bypass on a warm engine when the second stage was activated. Raising the filter bypass setting forced the filter to do what it designed to do. Filter. Preventing debris from circulating during high load, high rpm operation.    So next question is how did GM find this out? VLOM/lifter failures and a deep dive by Melling Corp.    Last question. Is it required? Look at it like this; a motor may be equipped with a rev limiter. But it only works if the set point in reached. That 22 psig setting only matters if the pressure differential across the filter media exceeds 15 psig during normal warm operation. Second stage kicks in around 3000-3500 rpm.    I can't answer your question because I don't know you and how you use the truck. But I think there is enough information here to let you decide for yourself. 😉

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...