Jump to content

holy FNG not anotherone!!!!!!!

meadow99

By meadow99
in The Off-Topic Bar

Recommended Posts

meadow99 New Member

meadow99

Posted
Posted

hi guys im hailing from lansing Michigan freekin cold up here now

any ways this is my secoldn truck my first was a 1994 silverado 350 4x4 yada yada

 

ive been hearing talk about a lot of these little doit yourself engine mods.. id like to know how to do some of them and if they realy work or not? things like the timing and egr and the coolant line deal..

can youall tell me how to do them and if they work or not

 

thanks

ive got a 1999 x cab meadow green ls with 4.10s and 285/75/16 pathfinder ATR s  with the torsien bars cranked..

 

thanks folks

  • 2 weeks later...
chevy4x4trucks Senior Enthusiast

chevy4x4trucks

Posted
Posted

Welcome to the forum  :flag:  :cheers:

 

Those mods may give some performance gains but nothing all that noticeable.

 

You'd be better off making a custom Cold Air Intake, reworking the exhaust, and other stuff like that for some more noticeable power gains.

 

Either way, it's all just another mod to add to the list :lol:

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • newdude
      LCA bolts

      By newdude · Posted

      I would argue that GMPartsDirect has that info wrong.    The service manual for R+R the lower arm and for adjusting camber/caster, none of the steps say to discard and replace the nut or the bolt.    The only part that gets discarded is the plastic cam adjustment retainer that is in the eccentric from the factory.     The LCA nut torque spec is: First Pass: 180 Y (133 lb ft) Final Pass: 90 –105 Degrees    
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      The filtering to wear relationship goes like this:      'Relative Engine Life "Factor" new divided by the factor old. So 8/3= 2.67. That result is the multiplier thus if a motor had an effective life of 100K using a filter with a 45 micron rating at a Beta ratio of 75 then a filter with a micron rating of 10 at a Beta of 75 would improve expected engine life to 267,000 miles.    Wear metals are an indirect indicator. Less is better and the motor lives longer but there isn't a multiplier like there is for filtration so well documented. Most of that has to do with the sensitivity of the wear metals tests themselves. They read a 'slice' of the spectrum but not the absolute values for the entire spectrum. So a general indicator that is used WITH the results of other tests. Two others considered in this post. Trending is very important.    There is also the influence of corrosive wear which may be seen in the wear metals but separate from load based or viscosity mitigated indication. It's a small graph but the gray line is wear vs the TBN/TAN crossover. Not as useful as it used to be as there are now new chemistries for acid remediation that don't show up in standard UAO testing. They will catch up or be found liars. Only two possible outcomes, eh?             
    • mikeyk101
      TCM Tuning 6L80E

      By mikeyk101 · Posted

      One thing that comes up over and over is that the torque converters are the weak link. Many of the failed transmissions have the same thing in common. The torque converter grenades and then metal torque converter shards end up destroying the transmission. One of the best things you can do is if your transmission is still fully functional, change out to one of the aftermarket billet torque converters. There are several good choices mentioned in different threads here to make your choice. After that, then you can decide about trans tuning. My trans failed at around 95,000 miles. It got replaced under the GM protection plan. The remanufactured trans comes with a 100,000 mile /3 year warranty. I still have just under 1 year left. So far, so good. As long as it's still working good next year, an aftermarket torque converter is going to get installed early spring. If the trans and OEM torque converter fail by then, I will get it replaced under warranty and immediately have an aftermarket torque converter installed. A warranty replacement trans of a replacement trans will no longer have the warranty so I will bulletproof it from the get go.
    • Grumpy Bear
      Gas Prices

      By Grumpy Bear · Posted

      You got'a be cooking right now. Just looked at the weather map. Yuck!    We are right back to $4 today.    
    • CamGTP
      Gas Prices

      By CamGTP · Posted

      Pushing $4.00 a gallon in most places, still $3.75 in town but it's going to spike tomorrow for sure.   Diesel back up to $4.60-5.00.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...