Jump to content

Ready Lift Or Rough Country

Nate08

Recommended Posts

Nate08 Enthusiast

Nate08

Posted
Posted

I know this question is prolly played out on here, but im new on here so bare with me. I just got a 08 GMC Seirra. It sets a lil to low in the front, kind of like driving a car compared to my old truck. So ive decided to get a 2in leveling kit, but can't make my mind up on which one. Everyone around here gets the Ready Lift because there is a shop local that installs them. I plan on doing the installation my self but can't make up my mind. Any suggestions and photos would be greatly appreciated.

cobrajet84 Senior Enthusiast

cobrajet84

Posted
Posted

Most people on this site go with the rough country one as it is the cheapest way to level by far. I wanted just a bit more lift, and while i have heard nothing but good things about the rough country, i like metal parts so i went with the ready lift. I installed it myself, took probably longer than most people would take due to my lack of pneumatic tools and taking it slowly to make sure i did it right. I also had a lunch break, lol. My sig shows my truck with the level and and 3" rear blocks. here is the link to my posts with pictures and measurements. ready lift level and 3" rear blocks

Xenomorph Enthusiast

Xenomorph

Posted
Posted

Im also debating between both leveling kits. One thing I find odd is that the Rough Country is 2" where the Ready Lift claims their 2.25" billet kit is the proper front end lift required to achieve a true level stance.

 

Opinions?

travishale84 Enthusiast

travishale84

Posted
Posted
Im also debating between both leveling kits. One thing I find odd is that the Rough Country is 2" where the Ready Lift claims their 2.25" billet kit is the proper front end lift required to achieve a true level stance.

 

Opinions?

 

 

when i installed the RC 2" leveling kit on my 2011 it made my ext. cab truck ride nose high until i installed a 2" block in the rear. this gave me about 1/4-3/8" of rake. IMO a 2" level with a 3" block adds WAY too much rake back to the truck. but if you like that sort of look then its perfect.

Xenomorph Enthusiast

Xenomorph

Posted
Posted

Anyone know if there are any YouTube videos that show the instalation of the Ready Lift 2.25" front end lift kit? I've checked and can't find one, only other makes/ models. Preferably looking for a video that shows a 2011 or newer model Silverado. Thanks all.

 

This kit specifically:

 

LINK to kit

 

299.jpg

cobrajet84 Senior Enthusiast

cobrajet84

Posted
Posted
Anyone know if there are any YouTube videos that show the instalation of the Ready Lift 2.25" front end lift kit? I've checked and can't find one, only other makes/ models. Preferably looking for a video that shows a 2011 or newer model Silverado. Thanks all.

 

This kit specifically:

 

LINK to kit

 

299.jpg

 

 

If you look at the leveling kit on ready lift they have an installation video on there. In fact thats mostly how I installed mine, is by watching the video. I wouldn't gowith the T6 as it requires cutting of the stock bolts.

Xenomorph Enthusiast

Xenomorph

Posted
Posted
If you look at the leveling kit on ready lift they have an installation video on there. In fact thats mostly how I installed mine, is by watching the video. I wouldn't gowith the T6 as it requires cutting of the stock bolts.

 

Ahhh thanks and good call, I missed that. Just checked the site again and found this one with a video for bolt-on install.

Looks like this kit kinda does what the T6 and RC does at the same time by installing a spacer above and below the strut. I would imagine that this better distributes any added stress.

 

Down side of RL when compared to RC is obviously the price...

 

ReadyLift%202007-2010%20Chevy%20Silverado%20GMC%20Sierra%201500%202.25%20inch%20Leveling%20Kits.jpg

Live2FlyLow Enthusiast

Live2FlyLow

Posted
Posted

I just installed the ReadyLift 2.25 leveling kit on my 08 GMC Sierra AT and over am very pleased with the quality, ease of application and end result. I can attest that their 1-800 Customer Support staff are friendly, knowledgeable and helpful.

JTRebel Enthusiast

JTRebel

Posted
Posted

What have guys been doing with the Denali Pickups. I have an 09 and Ready Lift said their leveling kit would cause vibration due to the Denali's AWD.

Xenomorph Enthusiast

Xenomorph

Posted
Posted
I'd go with RC for price and ease of installation.

 

I gotta agree with you... Im personally just looking to do a level kit as a temp thing to give my truck a more aggressive stance. Ultimately I wanna go with a 6" lift, larger tires, etc. Just gotta put some cash aside. The RC may be a good inexpensive solution for the time being.

Nate08 Enthusiast

Nate08

Posted
  • Author
Posted
I just installed the ReadyLift 2.25 leveling kit on my 08 GMC Sierra AT and over am very pleased with the quality, ease of application and end result. I can attest that their 1-800 Customer Support staff are friendly, knowledgeable and helpful.

 

 

You got any pics?? I was jus wondering how close to level it got you. A lil rake dont bother me but i dont want it to ride nose up. Im really planning on just a level kit to raise my stants a lil and be done with it. Its gonna be permanent so i want to make sure its the right one for what im looking for.

Live2FlyLow Enthusiast

Live2FlyLow

Posted
Posted
I just installed the ReadyLift 2.25 leveling kit on my 08 GMC Sierra AT and over am very pleased with the quality, ease of application and end result. I can attest that their 1-800 Customer Support staff are friendly, knowledgeable and helpful.

 

 

You got any pics?? I was jus wondering how close to level it got you. A lil rake dont bother me but i dont want it to ride nose up. Im really planning on just a level kit to raise my stants a lil and be done with it. Its gonna be permanent so i want to make sure its the right one for what im looking for.

 

 

I've tried to take a few pictures with my iPhone but honestly it's not clearly definable in the photos. The best I can describe, it truly levels the frame. When you step back and look at the truck on level pavement, you can visually detect a very slight nose low rake -- but it's minimal. Climbing into the truck and the appearance as you look down the now level hood while driving changes. I don't think you'd get a nose high attitude (what we call "raccoon hunting" as your headlights shine upward) unless you load the bed heavy or apply a trailer with a substantial tongue weight. If you want the pictures, PM me your cell number or E-mail address.

patch20 New Member

patch20

Posted
Posted
I've decided to go with the Rough Country 2" leveling kit. I want to get it done before the winter hits so hopefully I'll have pics soon. :thumbs:

 

 

Just helped a buddy put one on his truck.. took awhile but was well worth it.. good luck!

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • fondupot
      Exhaust heat while towing!

      By fondupot · Posted

      You can install tailpipes that direct the exhaust sideways vs the OEM one that goes straight back. There are several on the market, do you own research. HOWEVER, you need to make sure the Venturi vents are still intact, otherwise it will throw a engine code. There is a sensor somewhere that detects back pressure on the exhaust. And if it doesn't collect the correct metrics, it will throw the truck into limp mode. 
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      "Teardown" is complete. Head surfaces are clean and ready, new intake is prepped and ready. Coolant drained and water pump is removed, radiator is removed, new hoses and pump are ready.   The replacement intake is also from a '95 (with I think 260k, the odometer said). Noticeably less pitting where it covers the rear coolant passages. I'm not sure if that's a tribute to more frequent use, more frequent coolant changes/upkeep, or if the intake was machined at some point. But it appears I found a good one.   My coolant hoses were original, and the lower hose still retained the factory spring inside. It's not really rusty, but it's got deposits all over it. Unsure if I should re-install it (will thoroughly clean it first). Someone said hose technology has gotten better since 1995 (has it?) and I don't need the spring. I think modern EPDM is what made those hoses last from 1995-2026, so it's a question of how much suction can the water pump really pull, and will it collapse the hose without a spring?   I'm stopped and waiting for parts, however.   When I first brought the truck home, the fan was intermittently hitting the radiator shroud. I could see someone had monkeyed with the shroud (put a bunch of cardboard as a spacer between the upper/lower shroud halves. Someone said the motor mounts have likely failed and the engine has sagged. I wasn't sure I believed that. The engine is really solid in its mounts: To remove the old intake I *just* nearly permanently welded to the heads with freshly cured RTV and gasket snot two weeks ago, I literally had to use the arms on my lift and a chain with a bolt attached to the intake to pull it loose. It almost picked the front of the truck off the ground before ....scuuuuuuuuuuup.... I could actually hear the gaskets tearing and it broke loose and the whole truck settled back down. Motor barely moved.   SO, those parts I'm waiting on... The lower radiator mounts/bushings had completely failed. The radiator needs to be insulated from the rad support, and the bushings help the rad stand at the correct height. The plastic "baffle" was also destroyed at some point. Someone had attached the shroud to it incorrectly, overlapping a joint that should have been underlapped, creating another suspect issue potentially causing things to hit the fan. Broken tabs, side is busted off, and it's perma-formed/bent where it was jimmied incorrectly.   The baffle? Unobtainum. Long since discontinued from GM, of course. Aftermarket/capa/chinese? Also unobtanium. In GM's infinite wisdom, it appears there are at least two different variations whether the Blazer is 2 or 4 door, and I can't yet tell if they shared the same part with the S-pickups. Plan B, if I can't find a viable used one, will be to create a bracket to re-assemble the critical joint I need to seal a gap with the shroud. But that will bug me, it won't be...perfect.   The water pump bolts appear to have been installed with...plumber's putty. I guess, sure, if it works...? I've found a few "backyard fixes" like that. Someone's been here before....   If I can't find someone to jam bamboo under my fingernails to fill my free time this week I think I'll install the driver's power window motor and replace the rear door speaker that's inop. I've got a genuine GM "9.5" ohm working replacement. Why GM used a non-standard resistance....nevermind. Of course they did, you can get more sound from a cheap factory amp that way.   And the saga goes on...
    • glenn27
      Different requirements for oil filters?

      By glenn27 · Posted

      // Thank you, also for your  response. More information is always good. This 2013 GMC is most likely my 'forever truck"-I'm 77 and retired...and truck only has 42K on it-very clean-so I try to keep it that way.  Tks again for your  response- glenn
    • smooth68
      Alternate wiring for Kicker sub with Bose system. (DO THIS)

      By smooth68 · Posted

      I started my install this weekend. Everything was pretty straight forward but I ran into one issue with running power through the firewall. The nipple grommet on my High Country already has a small harness running through it - has anyone else ran into this issue? And on the engine bay side, does the wire basically just penetrate the factory wiring boot? I did this on my '22 Trail Boss and it seems much easier but thats been a few years. My other thought would be possibly drilling a new hole adding a rubber grommet just to the lower left of the factory hole. Thoughts?   Has anyone used a T-harness off the Bose amp and obtained power from there? It seems a little odd that such a small amp needs 3 power leads
    • glenn27
      Different requirements for oil filters?

      By glenn27 · Posted

      ///// Ok--Thanks for that info--I could not find yesterday when I looked for the specs on that NAPA filter what I wanted. Their website is not very user friendly. I buy all teh filters for  our three vehicles once or twice a year. Have always run NAPA Gold on everything I own....I buy it thru my Son's account for his business-which he has a Heavy Equipment repair shop-one reason he uses NAPA so much-they have such a full line of coverage for just about anything/anywhere- He gets s  good discount because of volume bought. Anyway-Thank you -Sir for your response.   glenn

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...