Jump to content

Billet Bowtie

Kania2k1

Recommended Posts

Kania2k1 Senior Enthusiast

Kania2k1

Posted
Posted
I installed my billet bowtie about mid summer.  This is the first winter I've had it.  The snow/salt/general road crap seems to be damaging it a bit.  Kinda dull looking.  Should I just hit it with a little wenol and then Zaino to protect it or what?

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,858
    Total Members
    8,960
    Most Online
    mark2
    Newest Member
    mark2
    Joined

  • Who's Online   5 Members, 0 Anonymous, 600 Guests (See full list)

  • Latest Articles

  • Posts

    • Grumpy Bear
      Slate Electric Truck

      By Grumpy Bear · Posted

      Most say the oil temperature needs to above the boiling point of water to rid it of moisture and long enough to dry it. Many think that is about a hour at 212 F or more. Those people have never line dried cloths in a Midwest winter. Leave a pan of water sitting on the counter and eventually it all evaporates. So heat drives the time it takes. Water in oil under 175 F, the Nitration initiation temperature, is a minimum then for temperature and samples I've done that use Karl Fisher method say about a hour (in a healthy well tuned motor) over 175 F will dry it to under 800 ppm. Low enough to not be much of a factor. Motors with weak rings will take longer and the colder the air temperature the longer it takes.   On a cold motor there is also the condensation temperature. Blowby gases that contain moisture are subject to that cold cylinder wall, like sweat on a glass of ice tea. But also subject to the Law of Partial Pressures. Wear studies by GM and the DOD  indicate wear is a real issue below 85 F and a concern to 140 F but doesn't become a minimal factor until about 160 F. You know this intuitively when you see water vapor exit the exhaust pipe until the system gets above the dew point. It isn't magic, it's physics and it fascinates me. I know you didn't ask but....I over share sometimes. 😉    You keep the Camaro's high and tight.  
    • asilverblazer
      Slate Electric Truck

      By asilverblazer · Posted

      Move further away.   Benefit of living out - none of our cars get short cycled, plenty of warm up time.   Curious how much time/temperature it takes to drive moisture/condensation out of the engine?
    • diyer2
      Transmission Temperature Hitting 220s

      By diyer2 · Posted

      Switch a a 100% synthetic trans fluid, Amsoil works for me.
    • DustMcGrath
      Transmission Temperature Hitting 220s

      By DustMcGrath · Posted

      First of all sorry, I know there are a ton of transmission temperature threads...   My truck is a 2025 LZ0 High (10l89 10-speed) High Country with NHT max trailering package. The NHT package is supposed to have "enhanced cooling."   Normally the trans temp sits around 200. It seems like with any real stress it quickly jumps into the 220s (for example climbing a grade unloaded at lower speeds). I haven't towed much with this truck, but I'm concerned if it gets this hot unloaded.    I've tried a few different things to keep the temps down (tow/haul mode, sport mode, low range when that makes sense) and nothing seems to affect it.    I'm curious if others are the same behavior or if anyone has found techniques to keep the temps down. It seems like it just can't handle reduced airflow at lower speeds, even with relatively light loading.    Thanks!      
    • cautious optimist
      2027 3.0 l Duramax

      By cautious optimist · Posted

      I'm at 105,000 miles on my baby Duramax. No issues yet. I hit 31 mpg's traveling through hilly terrain to a project in Colorado. I will buy another 3.0. I'm not concerned.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...