Jump to content

Drivers door unlock/mirror/windows not working

jarettg

By jarettg
in Ask A GM Technician

Recommended Posts

jarettg Enthusiast

jarettg

Posted
Posted

I'm hoping the forum can help me with this one. My drivers door is having some issues. Sometimes the door lock does not lock/unlock and none of the window switches or mirror adjust buttons do not work. A day later they are working again.

 

I took it into GM to get checked out and they said everything was working fine; that day I suppose.

 

I'm thinking it has something to do with the wiring in the door is getting pinched or frayed.

 

This is turning into a major pain as I have to double check that my door is getting locked and having to use the key to enter into the vehicle.

montyss Enthusiast

montyss

Posted
Posted

check the wires in the boot that goes between the door and the cab , just pull the rubber boot out of the door and give a little tug on the larger pink or red wires . The wires sometimes break in the middle of the boot from the wires bending from the door opening and closing.

  • 2 weeks later...
demech23 Enthusiast

demech23

Posted
Posted

check the wires in the boot that goes between the door and the cab , just pull the rubber boot out of the door and give a little tug on the larger pink or red wires . The wires sometimes break in the middle of the boot from the wires bending from the door opening and closing.

 

See this happen all too often, checking the wiring between door and body would be a good place to start.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • KARNUT
      The Peckish Synapse

      By KARNUT · Posted

      If it has a stick I can have fun with it. When my wife first got her Acura years ago I used to tease her about it. I was only interested in muscle cars. They’re gone now. So once a month I drive the Acura. Every once in a while I’ll take it to Redline. But just normal driving on some twisty back roads usually does the trick. 
    • contrabombarde
      2010 Avalanche 5.3 not running correctly after engine swap.

      By contrabombarde · Posted

      I went through again with a test light and everything checked out.    I suppose it could be the MAF itself but I've tried 3 different sensors, 2 of which were in running vehicles previously (the one in this truck, and the one in the donor truck), as well as a new one I picked up from NAPA. I would just be surprised if all 3 were bad.   EDIT/UPDATE: I swapped in the MAP sensor that was originally with the 2010 PCM, that made the code for map sensor voltage high Go away, and the map sensor seems to read normal with key on engine off (14psi or so), but it still doesn't run and does the same thing as before.
    • Atlas
      No Software Updates - Old Build

      By Atlas · Posted

      In addition to a cell or wifi connection, the infotainment needs to be enabled to download software updates. That's a toggle within the system settings.   But...if the truck was prevented from receiving updates in a past life, missing a bunch of updates may mean it won't go back and download all of those because they're not available or the system is too far out of date.   If a formal recall depends on a software update, the recall for that truck remains in an open status until it's applied. The dealer would need to apply the software update in that instance.   Most updates downloaded and applied via the infotainment aren't recalls/safety recalls, they're enhancements and usability fixes which aren't critical.
    • Vu1can
      Brake Pad Warning Message

      By Vu1can · Posted

      Recently I've been getting a message, "New Brake Pads Detected. Reset Brake Pad Life?", But I haven't had the pads replaced and the truck only has 28,000 miles. The Brake Pad Life shows Front 64% and Rear 79%. I select NO to resetting the brake pad life and the message goes away but comes back at the nest restart.   I stopped by the dealer and was told that it sounds like a software glitch that would require reprogramming. Even though I have the extended warranty, they tell me that reprogramming is not covered unless a module was actually bad and needed to be replaced. Simply reprogramming is not covered. So, they want $200.00 just to diagnose the problem. If it turns out no bad module, another charge on top of that to do the reprogramming. If the cause was an actual bad module, everything would be covered under the warranty.   Just wondering if anyone else has had this problem. Should this issue be covered under the warranty?   Thanks
    • newdude
      Tire psi

      By newdude · Posted

      NHT is diesel only, correct.     The GVWRs for NHT on 3/4 ton bring them to the same numbers as many of the 2WD 1 tons.  A crew 4x4 standard 3/4 with NHT is 11,750lbs, a 1 ton same cab/box/4x4 is 12,100lbs.     Hubs and hub bearings are the same for 11.5" and 12" axles.  Housing, diff carrier and ring/pinion are larger for the 12".   All gas use the 11.5" axle, 3/4, 1 ton and 1 ton DRW. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...