Jump to content

Low voltage issue

lance9386

By lance9386
in Troubleshooting & Recalls

 Share

Recommended Posts

Tracy Wafer New Member

Tracy Wafer

Posted
Posted

I have a2014 GMC SIERRA 1500 5.3.  I've had the battery, and the alternator replaced but I get this message periodically while driving as well as being idle. Any suggestions on what to do?

20210713_163901.jpg

  • 11 months later...
Jason Mitchell Enthusiast

Jason Mitchell

Posted
Posted

I Have a Silverado 3500HD with the 6.0L Gas engine. I have a low voltage situation that I don't believe to be "normal". The dash gauge shows normal 13.8V upon startup, then a few minutes it drops to about 10V. The needle settles just above the lower limit for "normal". I know that the user manual and manufacturer specifications describe this as a normal condition, and the charging system will lower the voltage to extend the battery voltage.

Here's the rub. A couple weeks ago, I took the truck on a 5 hour road trip. I noticed the needle drop during this trip. I left the vehicle and did what I had needed to do. When I returned, the truck started normally and operated well for the trip home. I stopped for gas just before parking the truck for the night. After filling, the battery didn't have sufficient charge to start the vehicle. I had the battery and alternator tested separate by removing each component and taking to a test facility. Both were fine on the bench. 

Why did I lose charge on the trip? Why do I never see the voltage gauge return closer to 14 volts? Anyone have experience with a similar condition?

  • Like 1
swathdiver Senior Enthusiast

swathdiver

Posted
Posted

The alternator will reduce output if it detects that the battery cannot take the charge.  It's literally a smart charger that determines the health of the battery.

 

How old is the battery?  I have had this happen and the battery was plumb wore out.  If you have an advanced scan tool, in the BCM module, you can see the condition of the battery as the computer sees it, start up state of charge, previous start up state of charge, calculated temperature, etc.  

Jason Mitchell Enthusiast

Jason Mitchell

Posted
Posted

I did physically remove the battery and take it to be tested. I charged it before taking it there because I wanted them to do the load test while full. After the surface charge wore off, it held 12.6 volts and the test resulted at 1100 cranking amps.

 

That being said, it is the factory 2017 battery.

  • Like 1
swathdiver Senior Enthusiast

swathdiver

Posted
Posted
7 hours ago, Jason Mitchell said:

I did physically remove the battery and take it to be tested. I charged it before taking it there because I wanted them to do the load test while full. After the surface charge wore off, it held 12.6 volts and the test resulted at 1100 cranking amps.

 

That being said, it is the factory 2017 battery.

 

I don't think that's enough volts, If the ambient temp was 75 degrees, 12.6 volts is 75% state of charge.  The shop manual for my truck (GMT900) says that when the state of charge drops below 64%, it's time to replace the battery.  That being said, your battery is 5 years old or so and down here in Florida, that's old.

 

Check your local dealers for battery coupons, they may even install it/them for free.

  • Thanks 1
diyer2 Senior Enthusiast

diyer2

Posted
Posted

Maybe I'm thinking wrong but with a 5 year old battery the first thing I would have done when that message popped up is put in a new battery. Going to have to buy one anyway, someday.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,902
    Total Members
    8,960
    Most Online
    whenindoubtuseahammer
    Newest Member
    whenindoubtuseahammer
    Joined

  • Who's Online   2 Members, 0 Anonymous, 387 Guests (See full list)

  • Latest Articles

  • Posts

    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      Its no wonder you've gravitated to the oil types and brands you have in later years after trying certain brands and one being a specialty oil or at least very hard to come by up here and the other would have been a commonly found oil of the era and the vastly different outcomes as a result to using the vehicles in question the same distance for an OCI . It shows what marketing hype can do without actually having the product to back up the claims and that is no different now with the insane claims that are written on the side of a bottle of oil from some of the off the shelf oils.    What has surprised me and I was already finding this out before I bought my truck with the GDI engine, that this newer fancy technology that seemingly would suggest better fuel economy/emissions with this high pressure spray of fuel is not in reality kind at all to the engine or at least the oils life. Yet they insist on claiming long OCI with this technology just like they did with the port or similar type fuel injection systems when in reality its a step back in oil life to have a GDI system.    I think the mistake your making Grumpy is that your not sending your samples to Blackstone and getting the feel good glowing report that you can run it another 1000 or more miles and then send another sample where they say run it yet another 1000 miles and on and on it goes until your sending in something that looks a lot like road tar and then they may suggest you change your oil within the next 1000 miles 😆
    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      I am guessing that engines of that design back then had a better ability to be abused and survive longer than a new design engine with the long timing chain and the overhead cams and phasers etc. But I would never guess that an engine could go that far and not fail spectacularly or at least die a slow death. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      In the 80's 90's I'd run Honda's 7,500 miles between changes using Red Line HP 5W20 and do it for hundreds of thousands of miles with issues. Back in the day it was an SAE 20 with the HTHS of a SAE 30 and SN add load. It was also very polar. Oxidation VOA was over 120. Besides those motors were SPFI and lean burn tech. I could have likely run it longer but never did.    We had a Toyota bought new I ran on Pennzoil's latest and greatest synthetic of the day with "Penthane". A made up word for a very low dose of PAO. Tried 7,500 mile OCI's in that Group III/VI chemistry and the rings tapped out at 90K. Rocker box wasn't as bad as the one Punch put up but it wasn't good either. Also a SPFI motor.    I'm around 3,750 across the board on these GDI monsters and the oil it tapped out by then usually on TBN/TAN crossover and color. Red Line HP Euro.    The AMSOIL SS brochures tell you to follow the OEM values for the service class but that it can be run up to 25K if monitored. I can't imagine what motor could go that distance and not tap out. I've never owned one.    Yes, I know. Lot's of people do. I'm just not going to be one of them. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      I knew a guy in the early 80's that bought a new Monte Carlo and ran it a 100,000 miles without ever changing the filter or the oil. Just kept adding. It looked like that inside.     
    • whenindoubtuseahammer
      My First Project and GMC has me stumped

      By whenindoubtuseahammer · Posted

      Good evening. I was lucky enough to get passed down to me a 2007 GMC LBZ that was my great uncle's. While the underside and rockers are more or less gone I feel like with time I can restore it to working order since it only has 110,000 miles and he put nearly every option he could get without getting the new body style since he did not trust DEF. So far I have done everything I can think of but when I put the key into the ignition nothing happens. I put 2 brand new batteries in it. Cleaned the terminals. Check all the fuses and relays and they all pass with my multimeter. I know I'm missing something that I just cant think of. The only odd thing is the OBD2 port works which makes me think its not the mega fuse. Any advice would be greatly appreciated. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...