Jump to content

New 2500 Denali Duramax

geektoad

Recommended Posts

geektoad Senior Enthusiast

geektoad

Posted
Posted

We're about to buy a travel trailer beyond the capabilities of my 1500, so today it got traded in on the new rig:

 

16denali.jpg

 

I can't say enough good things about this rig. I'm really impressed.

DBTravelers Enthusiast

DBTravelers

Posted
Posted

NICE! We were faced with similar issues, had a 35' travel trailer that we had been pulling with our 2013 GMC 1500 5.3. We will be trading for a 40' 5th wheel next year and I didn't want to worry if I had enough truck while out shopping. I just got really crazy and bought a little bigger also...3500HD SLT Duramax, CC, dually, 8' box. And we love it!

post-156191-0-80084100-1472265621_thumb.jpg

 

post-156191-0-80084100-1472265621_thumb.jpg

post-156191-0-80084100-1472265621_thumb.jpg

post-156191-0-80084100-1472265621_thumb.jpg

vertigo Enthusiast

vertigo

Posted
Posted

Congrats on the new truck, that black sure is sharp.

We did the same thing ( almost ) we had a 2011 F350 Dually that we traded in on a 2016 GMC Denali 3500 SRW. Drag a 38' 5th wheel and curious to see/feel the differences.

post-161326-0-92948000-1472266616_thumb.jpg

post-161326-0-92948000-1472266616_thumb.jpg

post-161326-0-92948000-1472266616_thumb.jpg

post-161326-0-92948000-1472266616_thumb.jpg

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,840
    Total Members
    8,960
    Most Online
    appletrav
    Newest Member
    appletrav
    Joined

  • Who's Online   2 Members, 0 Anonymous, 393 Guests (See full list)

  • Latest Articles

  • Posts

    • newdude
      Different requirements for oil filters?

      By newdude · Posted

      2013 5.3 still to this day calls for the PF48 filter.  Which as a 15psi bypass pressure.     There is a TSB, 17-NA-157 that talks about the PF-63 and PF-64 filters which have a higher bypass rating of 22psi.    TSB HERE - temp.xml   "Beginning in 2012, the oil pumps began to regulate main gallery feedback instead of pump out pressure. This means that the oil pump now does not begin to regulate until pressure is built up to the main gallery. This change reduces the amount of time it takes to provide oil to the engine bearing and lifters during extreme cold start conditions.  Main gallery feedback oil pump control systems are present on the following engine families which use Spin-on oil filters: Small Gas Engine (SGE), Large Gas Engine (LGE), High Feature (HFV6) Gen2 and Small Block Gen5 gasoline engines. These engines with the main gallery feedback oil pump control systems are factory built with an ACDelco® oil filters"   It also calls out what engines use those filters.  The gen 4 small blocks were not on that list (LMG, LC9, L9H, L92, L94, L20, L96).  Gen 5 small blocks use the higher pressure filter.       
    • Grumpy Bear
      Different requirements for oil filters?

      By Grumpy Bear · Posted

      Do you know WHY the filter relief setting was increased to 22 psig?    When the new system goes into the second stage the pump volume ramps up considerably. It was found that the 15 psi filter bypass setting put the filter in bypass on a warm engine when the second stage was activated. Raising the filter bypass setting forced the filter to do what it designed to do. Filter. Preventing debris from circulating during high load, high rpm operation.    So next question is how did GM find this out? VLOM/lifter failures and a deep dive by Melling Corp.    Last question. Is it required? Look at it like this; a motor may be equipped with a rev limiter. But it only works if the set point in reached. That 22 psig setting only matters if the pressure differential across the filter media exceeds 15 psig during normal warm operation. Second stage kicks in around 3000-3500 rpm.    I can't answer your question because I don't know you and how you use the truck. But I think there is enough information here to let you decide for yourself. 😉
    • Coastie05
      give me some tips to make my truck look better

      By Coastie05 · Posted

      Go back to OEM wheels. 
    • newdude
      2020 Trailboss 6.2 replacement

      By newdude · Posted

      Probably not their first rodeo, so it should go as planned most likely.  Typically the service manager or tech doing the swap will put some seat time to shake it down after they get it all put back together.  We usually put 50-100mi before we hand them back so if something happens, its not after you get it.  A coolant leaks, oil leaks, a ground left off or loose, vibration, etc.     The new engines so far have been good?  There's been a couple that have popped out there again (the replacement engine) but most have been okay.  
    • CamGTP
      Different requirements for oil filters?

      By CamGTP · Posted

      To me it honestly makes zero difference what filter you run. It's not a race engine, just a truck engine that's mostly bumming highways and it just needs a filter that filters oil.   The filter used to be a 7060 and the long version was a 7045. Now it's the newer updated filter that the K2XX trucks and newer run, the 100255 I believe if we are using napa numbers. Any of those filters is going to do the job.   I wouldn't overthink it, to me it makes no difference because those first filter numbers worked for 18+ years before the spec suddenly changed.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...