Jump to content

Corner step removal and replacement

PghJeff2

By PghJeff2
in Modifications & Accessories

 Share

Recommended Posts

PghJeff2 Enthusiast

PghJeff2

Posted
Posted (edited)

Anyone know how to remove and replace these? Please tell me they can be removed without taking the bumper off. I am talking about the entire corner insert nt just the bottom tread.

Edited by PghJeff2
  • Like 1
Static Enthusiast

Static

Posted
Posted (edited)

I took mine off but I already had the bumper off. I dont see how you could possibly do it without removing the entire bumper. There are like 5 or 6 screws holding them on.

Edited by Static
sk Senior Enthusiast

sk

Posted
Posted

You can do it without removing the bumper but you need a wobble extension for your ratchet. I actually removed mine without removing the bumper to install some lights. I found instructions on the Anzo site where they sell replacement lighted steps (I didn't put those in but used the instructions to remove the step cavities):

 

http://www.anzousa.com/media/installation/e0da1a5a.pdf

  • Like 2
  • 1 year later...
ctsk8r Enthusiast

ctsk8r

Posted
Posted
On 4/26/2017 at 2:16 PM, sk said:

You can do it without removing the bumper but you need a wobble extension for your ratchet. I actually removed mine without removing the bumper to install some lights. I found instructions on the Anzo site where they sell replacement lighted steps (I didn't put those in but used the instructions to remove the step cavities):

 

http://www.anzousa.com/media/installation/e0da1a5a.pdf

Where do you find the screws behind the pocket? I see one that holds the slotted tab in but where is the other screw? 

  • 2 years later...
bc-chris Enthusiast

bc-chris

Posted
Posted
6 hours ago, Gunnaman32 said:

Did you wind up having to take the bumper off?  I don’t see any other way to install these.  Frustrating.

 

the anzo instructions  show how to do it without removing the bumper.  the link from above doesn't work but i saved the pdf when it was on the anzo webpage - hoping i can attach the file....   looks like it worked!  hopefully it will help you out!

 

bumper step removal.pdf

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,965
    Total Members
    8,960
    Most Online
    DaleB
    Newest Member
    DaleB
    Joined

  • Who's Online   1 Member, 0 Anonymous, 1,180 Guests (See full list)

  • Latest Articles

  • Posts

    • jgaudet99
      Tire psi

      By jgaudet99 · Posted

      My truck is a ¾ ton but my placard also says 80 for the rear tires, I think I might have the upgraded suspension to the 3500 series maybe.   I put my air down to 60 and the light was still on, and there was no way I was putting over 60 psi in the rear empty and not towing because I knew the actual number Toyo gave me and I didn't wanna ruin the center of my tires!   And you actually can change it in the settings from metric or is and it will show kph or mph then when you go into your tire settings it will be either psi or kpa, but it would be nice to just change it directly on the tire psi page 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      Common Sense Assembly   Your driveline is forgiving of the occasional mistake. It will even often forgive the random serious blunder. But it will not forgive a continuous bad habit.      What? Not everything needs to be a five thousand word essay.       
    • Grumpy Bear
      Gas Prices

      By Grumpy Bear · Posted

      We drove about 15 minute east today to visit a friend and saw a steep increase in price in the same county. About 50 cents a gallon steepper. 
    • Grumpy Bear
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Grumpy Bear · Posted

      Sure about that? A degree wheel and a dial indicator would lower your degree of assurance in that statement. 😉    It why we have offset keys and dialable timing sprockets. Just say'n.... I've built a few and have never seen one "On the money". 
    • Chuck FB
      Tire psi

      By Chuck FB · Posted

      I will admit I haven't experimented much with pressure drops beyond the numbers I put in and part of that is that the numbers I used are fairly low and then found out it would trigger regardless at that 35 psi. Having said that I had tried before had changed the placard pressures and being that I have a 1 ton set to 80 on the placard for the rear I believe it triggered close to 60, the front I don't recall now for sure but thought maybe it could get close to 45 from that factory 60 placard pressure. So I never did figure out if it was a number of psi from placard pressure to the alarm or a percentage of the total placard number as some figured it was like a 25% drop from placard pressure would trigger it. So as to try and answer your question, I believe I set the placard pressure on the front to 47 or so and while I run the front tires at 40, they have dipped below that some if its colder and I haven't put "winter air" in yet and never once have had the front alarm go off. I would say that the answer your looking for is no, that if you set your placard pressure to 45, you have a certain amount of room to drop below that pressure before the alarm will go off.    The pressures you decide to run in your truck, that ends up being what makes sense to you based on what your carrying in your truck or if towing, then have to bump them back up to something that will carry the load in the rear and the fronts typically left at the same pressure. It all comes down to that chart I put the link to and using an accurate roadside scale to be your guide, both unloaded and then loaded to know your minimum safe pressures.    I just wish GM would allow a person to change the readings for the tire pressures to the English system of pounds as I have to look at that goofy metric reading that will never ever jive in my head and will go over and change it just to figure out what they are if need be and then change it back. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...