Jump to content

High output alternator belt size

kickass audio
 Share

Recommended Posts

kickass audio Enthusiast

kickass audio

Posted
Posted

Since I wasted $160 in belts today as nobody had posted this anywhere online, I figured I would hopefully stop someone from blowing money and help them get something that fits.

 

I just replaced the factory alternator on my 2014 silverado 1500 today with a 370A mechman elite alternator. Since that alternator is high output it has a smaller pulley installed than the factory pulley. The OE alternator has a 2.5" pulley and the new Mechman alternator has a 2" pulley (that's their standard size for nearly all alternators). With the .5" difference in size you must get a smaller drive belt for the alternator, water pump and harmonic balancer or you will make the belt slip. In my case, the 72" factory length belt was right at the outermost limit of the tensioner so it definitely wouldn't work out.

 

I found that you will need to get a 71-1/4" outer circumference belt for the engine. In my case, NAPA didn't have the belt length in a 5 rib belt combination, they only had it in a 7 rib belt. I just used a utility knife to cut off 2 of the ribs and it works fine (plenty of other people I know do this and it's totally fine). The part number for this belt is through Gates as their fleet runner line under 080708HD, napa has it listed on their inventory as NBH 25-080708HD.

 

I hope this helps save someone else the hassle of cutting belts just to find they are too short. I will warn you, for this belt when it still had the 2 extra ribs on them, it wouldn't fit due to the extra deflection of the belt hanging off the lips on the pulleys, that made me worry as my two other belts were the same and even when I trimmed them it wouldn't fit.

 

Another word of caution, since you are getting an alternator with a half inch smaller pulley you will spin the alternator faster than the OE alt. Because of this I would not recommend you rev the engine up higher than 4700RPM. Going faster than that will over rev the alternator and can make it die (I did this in the past on my 2004 Envoy when I would floor it to get up to speed on the thruway and it would spin up really fast). The factory pulley size of 2.5" can handle you revving the engine up to 6000 RPM before risk of blowing up the alternator. Also you can NOT take the pulley from the OE alternator and stick it on the mechman alternator. The factory alt uses a centrifugal pulley that has grease inside (hence the black cap on the face of the pulley), I tried to remove that cap thinking it was a dust cover for the nut but it popped a bit of grease out in my face when I pried it off.

  • 8 months later...
Rockdigga New Member

Rockdigga

Posted
Posted

Should be a 6 rib 13/16" on your truck...I believe. I'm having same issue with my new high output alternator and finding a serpentine belt for a 14 silverado but I need one about 70 in 6 rib 13/16" 

  • 2 weeks later...
WashMan03 New Member

WashMan03

Posted
Posted
On 2/6/2021 at 9:40 PM, Rockdigga said:

Should be a 6 rib 13/16" on your truck...I believe. I'm having same issue with my new high output alternator and finding a serpentine belt for a 14 silverado but I need one about 70 in 6 rib 13/16" 

What belt did you end up going with?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,902
    Total Members
    8,960
    Most Online
    whenindoubtuseahammer
    Newest Member
    whenindoubtuseahammer
    Joined

  • Who's Online   2 Members, 0 Anonymous, 251 Guests (See full list)

  • Latest Articles

  • Posts

    • davester
      My First Project and GMC has me stumped

      By davester · Posted

      are there any codes? with lots of rust, perhaps disconnect/clean both sides of the connection/examine cable ends (the wires) for corrosion going into the sheath & replace if necessary/reconnect ALL the power AND ground cables between the battery, engine, frame, cab, fuse box and starter charm.li (website) has a no-start diagnostic procedure you can work through to get it working.
    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      Its no wonder you've gravitated to the oil types and brands you have in later years after trying certain brands and one being a specialty oil or at least very hard to come by up here and the other would have been a commonly found oil of the era and the vastly different outcomes as a result to using the vehicles in question the same distance for an OCI . It shows what marketing hype can do without actually having the product to back up the claims and that is no different now with the insane claims that are written on the side of a bottle of oil from some of the off the shelf oils.    What has surprised me and I was already finding this out before I bought my truck with the GDI engine, that this newer fancy technology that seemingly would suggest better fuel economy/emissions with this high pressure spray of fuel is not in reality kind at all to the engine or at least the oils life. Yet they insist on claiming long OCI with this technology just like they did with the port or similar type fuel injection systems when in reality its a step back in oil life to have a GDI system.    I think the mistake your making Grumpy is that your not sending your samples to Blackstone and getting the feel good glowing report that you can run it another 1000 or more miles and then send another sample where they say run it yet another 1000 miles and on and on it goes until your sending in something that looks a lot like road tar and then they may suggest you change your oil within the next 1000 miles 😆
    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      I am guessing that engines of that design back then had a better ability to be abused and survive longer than a new design engine with the long timing chain and the overhead cams and phasers etc. But I would never guess that an engine could go that far and not fail spectacularly or at least die a slow death. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      In the 80's 90's I'd run Honda's 7,500 miles between changes using Red Line HP 5W20 and do it for hundreds of thousands of miles with issues. Back in the day it was an SAE 20 with the HTHS of a SAE 30 and SN add load. It was also very polar. Oxidation VOA was over 120. Besides those motors were SPFI and lean burn tech. I could have likely run it longer but never did.    We had a Toyota bought new I ran on Pennzoil's latest and greatest synthetic of the day with "Penthane". A made up word for a very low dose of PAO. Tried 7,500 mile OCI's in that Group III/VI chemistry and the rings tapped out at 90K. Rocker box wasn't as bad as the one Punch put up but it wasn't good either. Also a SPFI motor.    I'm around 3,750 across the board on these GDI monsters and the oil it tapped out by then usually on TBN/TAN crossover and color. Red Line HP Euro.    The AMSOIL SS brochures tell you to follow the OEM values for the service class but that it can be run up to 25K if monitored. I can't imagine what motor could go that distance and not tap out. I've never owned one.    Yes, I know. Lot's of people do. I'm just not going to be one of them. 
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      I knew a guy in the early 80's that bought a new Monte Carlo and ran it a 100,000 miles without ever changing the filter or the oil. Just kept adding. It looked like that inside.     

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...