Jump to content

Door locks messed up

JohnnyGaloshes
 Share

Recommended Posts

JohnnyGaloshes New Member

JohnnyGaloshes

Posted
Posted

OK so i have a 2009 GMC Sierra 1500 king cab.

 

The drivers door power windows control switches will:

1. Lower the 2 rear, but will intermittent roll them up with much fuss with buttons.

2. Will roll up passenger door up, but not down (I hear the clicking, but not action).

3. Rolls the driver door up and down like normal.

 

The passenger door window switch will:

1. lower window, but not raise it.

 

The rear doors each window switch will:

1. lower them, but not raise it.

 

Is there all defective switches? Or is it all based on that driver power windows switch.

 

Suggestions appreciated.

 

P>S> the windows roll up and down with normal speed, when they work LOL

Sharpz Enthusiast

Sharpz

Posted
Posted

sounds like a bad connection issue, possibly a ground issue. Only way to be sure is to remove the panels and clean up the connections, check for corrosion, and possibly low volts. Start with the drivers door, and with the panel off and having cleaned the connections see if it helps your issue, if not move to the passenger door, and clean that one, then once again check to see if the issue has been resolved.

  • Like 1
swathdiver Senior Enthusiast

swathdiver

Posted
Posted
On 5/4/2021 at 2:40 PM, JohnnyGaloshes said:

OK so i have a 2009 GMC Sierra 1500 king cab.

 

The drivers door power windows control switches will:

1. Lower the 2 rear, but will intermittent roll them up with much fuss with buttons.

2. Will roll up passenger door up, but not down (I hear the clicking, but not action).

3. Rolls the driver door up and down like normal.

 

The passenger door window switch will:

1. lower window, but not raise it.

 

The rear doors each window switch will:

1. lower them, but not raise it.

 

Is there all defective switches? Or is it all based on that driver power windows switch.

 

Suggestions appreciated.

 

P>S> the windows roll up and down with normal speed, when they work LOL

If you have to replace either door switch assembly, it will have to be programmed to the vehicle if it is new.  If buying used, get one with the exact same options as your CREW CAB, lol.  There's a company on Ebay that sells the factory switches in white boxes, from same factory in Mexico that makes them for GM for about $7 each.

snailtrax Enthusiast

snailtrax

Posted
Posted
18 hours ago, swathdiver said:

If you have to replace either door switch assembly, it will have to be programmed to the vehicle if it is new.  If buying used, get one with the exact same options as your CREW CAB, lol.  There's a company on Ebay that sells the factory switches in white boxes, from same factory in Mexico that makes them for GM for about $7 each.

They do not require programming. I have personally changed 15 or so. Plug and play.

  • Like 1
snailtrax Enthusiast

snailtrax

Posted
Posted
45 minutes ago, JohnnyGaloshes said:

I took the driver door and passenger door switches apart, cleaned the terminals and it works like a charm. Thanks gang!

No problem. That's why we are here.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,965
    Total Members
    8,960
    Most Online
    DaleB
    Newest Member
    DaleB
    Joined

  • Who's Online   4 Members, 0 Anonymous, 1,414 Guests (See full list)

  • Latest Articles

  • Posts

    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      Common Sense Assembly   Your driveline is forgiving of the occasional mistake. It will even often forgive the random serious blunder. But it will not forgive a continuous bad habit.      What? Not everything needs to be a five thousand word essay.       
    • Grumpy Bear
      Gas Prices

      By Grumpy Bear · Posted

      We drove about 15 minute east today to visit a friend and saw a steep increase in price in the same county. About 50 cents a gallon steepper. 
    • Grumpy Bear
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Grumpy Bear · Posted

      Sure about that? A degree wheel and a dial indicator would lower your degree of assurance in that statement. 😉    It why we have offset keys and dialable timing sprockets. Just say'n.... I've built a few and have never seen one "On the money". 
    • Chuck FB
      Tire psi

      By Chuck FB · Posted

      I will admit I haven't experimented much with pressure drops beyond the numbers I put in and part of that is that the numbers I used are fairly low and then found out it would trigger regardless at that 35 psi. Having said that I had tried before had changed the placard pressures and being that I have a 1 ton set to 80 on the placard for the rear I believe it triggered close to 60, the front I don't recall now for sure but thought maybe it could get close to 45 from that factory 60 placard pressure. So I never did figure out if it was a number of psi from placard pressure to the alarm or a percentage of the total placard number as some figured it was like a 25% drop from placard pressure would trigger it. So as to try and answer your question, I believe I set the placard pressure on the front to 47 or so and while I run the front tires at 40, they have dipped below that some if its colder and I haven't put "winter air" in yet and never once have had the front alarm go off. I would say that the answer your looking for is no, that if you set your placard pressure to 45, you have a certain amount of room to drop below that pressure before the alarm will go off.    The pressures you decide to run in your truck, that ends up being what makes sense to you based on what your carrying in your truck or if towing, then have to bump them back up to something that will carry the load in the rear and the fronts typically left at the same pressure. It all comes down to that chart I put the link to and using an accurate roadside scale to be your guide, both unloaded and then loaded to know your minimum safe pressures.    I just wish GM would allow a person to change the readings for the tire pressures to the English system of pounds as I have to look at that goofy metric reading that will never ever jive in my head and will go over and change it just to figure out what they are if need be and then change it back. 
    • TrueBlue
      No Software Updates - Old Build

      By TrueBlue · Posted

      That part I understand, that the dealer can do it. But I'm not understanding why updates that were available to the truck since it left the factory, or the dealership originally, would not still be available to it without dealer intervention.   I'm thinking along the lines of recalls. They stay available until they are completed, regardless of whether they are in warranty or not, or in the hands of the original owner or not. Why not updates as well, especially since some of those can be safety related also?

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...