Jump to content

Power door locks work intermittently

danno0676

By danno0676
in Troubleshooting & Recalls

 Share

Recommended Posts

danno0676 New Member

danno0676

Posted
Posted

2015 Silverado 4 door LT

On occasion NONE of the power door locks work, either with the key fob or the switch on either of the front doors.

When this happens and you use the key fob lock/unlock feature the exterior lights will still illuminate and the horn will sound, but the locks will not move. 

I do not hear any clicking, either with the fob or the lock switch, no sounds, no nothing. The, randomly, it all starts working again...until it doesn't.

steelerdude15 Enthusiast

steelerdude15

Posted
Posted

I’d start by looking at your battery and grounds. If the battery is weak or the terminals are corroded, that can cause electrical issues. If the ground behind the front passenger wheel well is dirty or if the ground next to the front left speaker in the dash is touching insulation, they can cause issues too. I’d make sure your grounds are clean, tight and free from any debris.

  • 1 year later...
Binder49 Enthusiast

Binder49

Posted
Posted

I would check the harness in the left front door jamb for broken wires. Had the same problem with my 2014 Silverado. Found multiple broken wires. Repaired the harness, soldering and heat shrinking the breaks now everything works perfect.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • KARNUT
      The Peckish Synapse

      By KARNUT · Posted

      If it has a stick I can have fun with it. When my wife first got her Acura years ago I used to tease her about it. I was only interested in muscle cars. They’re gone now. So once a month I drive the Acura. Every once in a while I’ll take it to Redline. But just normal driving on some twisty back roads usually does the trick. 
    • contrabombarde
      2010 Avalanche 5.3 not running correctly after engine swap.

      By contrabombarde · Posted

      I went through again with a test light and everything checked out.    I suppose it could be the MAF itself but I've tried 3 different sensors, 2 of which were in running vehicles previously (the one in this truck, and the one in the donor truck), as well as a new one I picked up from NAPA. I would just be surprised if all 3 were bad.   EDIT/UPDATE: I swapped in the MAP sensor that was originally with the 2010 PCM, that made the code for map sensor voltage high Go away, and the map sensor seems to read normal with key on engine off (14psi or so), but it still doesn't run and does the same thing as before.
    • Atlas
      No Software Updates - Old Build

      By Atlas · Posted

      In addition to a cell or wifi connection, the infotainment needs to be enabled to download software updates. That's a toggle within the system settings.   But...if the truck was prevented from receiving updates in a past life, missing a bunch of updates may mean it won't go back and download all of those because they're not available or the system is too far out of date.   If a formal recall depends on a software update, the recall for that truck remains in an open status until it's applied. The dealer would need to apply the software update in that instance.   Most updates downloaded and applied via the infotainment aren't recalls/safety recalls, they're enhancements and usability fixes which aren't critical.
    • Vu1can
      Brake Pad Warning Message

      By Vu1can · Posted

      Recently I've been getting a message, "New Brake Pads Detected. Reset Brake Pad Life?", But I haven't had the pads replaced and the truck only has 28,000 miles. The Brake Pad Life shows Front 64% and Rear 79%. I select NO to resetting the brake pad life and the message goes away but comes back at the nest restart.   I stopped by the dealer and was told that it sounds like a software glitch that would require reprogramming. Even though I have the extended warranty, they tell me that reprogramming is not covered unless a module was actually bad and needed to be replaced. Simply reprogramming is not covered. So, they want $200.00 just to diagnose the problem. If it turns out no bad module, another charge on top of that to do the reprogramming. If the cause was an actual bad module, everything would be covered under the warranty.   Just wondering if anyone else has had this problem. Should this issue be covered under the warranty?   Thanks
    • newdude
      Tire psi

      By newdude · Posted

      NHT is diesel only, correct.     The GVWRs for NHT on 3/4 ton bring them to the same numbers as many of the 2WD 1 tons.  A crew 4x4 standard 3/4 with NHT is 11,750lbs, a 1 ton same cab/box/4x4 is 12,100lbs.     Hubs and hub bearings are the same for 11.5" and 12" axles.  Housing, diff carrier and ring/pinion are larger for the 12".   All gas use the 11.5" axle, 3/4, 1 ton and 1 ton DRW. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...