Jump to content

Console sub upgrade

Arthur Davis

By Arthur Davis
in Modifications & Accessories

 Share

Recommended Posts

Arthur Davis Enthusiast

Arthur Davis

Posted
Posted

Hi to all. I read a few older threads about boxes that were built to replace the factory 6". But, it's seems no one is doing it anymore. The JL audio stealthbox is way too expensive & I'm not a JL fan. Does anybody know the box dimensions? I would like to make 1 for myself. Thanks for any help.

Buckwild27 Enthusiast

Buckwild27

Posted
Posted

If you're planning on putting it in the center console or anywhere for that matter the sub you choose to use has required air space specs just use that to figure out your box design 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Arthur Davis Enthusiast

Arthur Davis

Posted
  • Author
Posted

Thanks for your reply. However my main concern is about the allowed space in the console. The max length width & height. I wanna pick the sub based on that. Just don't wanna go through the headache of taking it apart to measure, reassemble, then apart again to install

lonestardiver Enthusiast

lonestardiver

Posted
Posted

I have a sub box that was made to go in the console with a kicker 8” square sub. The sub has dual 2 ohm voice coils currently in parallel for a 1ohm load. I had plans for this to replace the Bose factory sub in my 2018 GMC but ended coming across a JL stealth box for a half decent price so the original plans have changed. I just haven’t had the time to post it up for sale.

lonestardiver Enthusiast

lonestardiver

Posted
Posted

It was made specifically for the kicker square sub which is what I put into it.

 

I’ll consider $200 plus shipping which is a loss on my side but I need to clear it out for room in my garage.

lonestardiver Enthusiast

lonestardiver

Posted
Posted

As a note, there is not as much space under the console as you would think since the transmission tunnel extends up into the console. Thus you are limited to the size of the sub and enclosure.  

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • chris21
      Brand new to this forum. Questions about re-gearing my 26’ HD

      By chris21 · Posted

      37's would probably fit with a 3" lift. GM only has two gear ratios for these trucks 3.73 for gas and 3.42 for diesel. And they can't be programmed for anything else at the moment. The rough country module just corrects the speedometer and odometer to adjust for tire size it's not a programming device.   You haven't said if your truck is gas or diesel, but for a gas truck the 10L1000 with 3.73 gears has a lower final drive ratio than the 6L90 it replaced would if it were swapped to 4.10s. GM used the same 3.73 gearing in 6 speed gas trucks. I don't think you'll have any issue running 37's with the 10 speed other than the reduction in mpg and towing/weight capacity which is as much of a function of the lift as the tire size.
    • GN2018
      Range AFM/DFM Disabler Flaw

      By GN2018 · Posted

      Actually, it probably was the brakes.  It's weird the way the messages came across, but I took it to the dealer thinking that something was wrong with the sensor and in fact, the rear brakes were shot.  What I don't understand is why the messages never said, your brake pads are low.  First I got the message I posted above, taking about new pads being detected.  Then I got a message saying that the system needed repaired.  It never said, change your brake pads.
    • No1UKnow
      Transmission Woes :-(

      By No1UKnow · Posted

    • ryan35205
      Lets Talk Z60 Suspension

      By ryan35205 · Posted

      Did the KYBs keep it the same height in the front? I was concerned that pre-assembled assembly would raise it up an inch to standard non-z60 height.. I guess which it would make the rake 1 inch instead of 2 inches.
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      Thank you for keeping the train on the tracks and for a thoughtful engagement. I enjoyed the reflection on a previous stance to refine and improve your position. I like that inquisitive flexibility about you Atlas.    No the process isn't sterile. Hundreds, perhaps thousands of miles of piping, vessels, pumps. Chevron, the people I worked for, were keenly aware that there is a market for what is known as their "ISOCLEAN" line of lubricants. These are lubricants that are the same as those sold bulk that are further processed by filtration to a level your particular application demands. They will filter and package and provide lab documentation as required. Do not kid yourself. Every gallon of oil that goes into a Chevron Turbine, reciprocating compressor, generator is prefiltered and tested before being charged. Lest wise it was when I was there in the plants I worked in.    There are requirements set by manufactures for the cleanliness of the oils used in their equipment. OTR such as CUMMINS has standards shared with customers on this. Commercial interest selling to Ma and Pa do, but don't share that information. Not even upon request but internally, they do exist.    The GM study sited, (Graph from Machinery Lubrication in previous post) only shows "relative" importance.  I find that fascinating. By constructing the graph like this they admit there are dozens of factors in engine life and via scientific method determined the effect of 'relative cleanliness' on engine life not in miles but in 'FACTORS'. This allows a certain amount of reverse engineering does it not?   They even provided some touchstones. Beta 75 as a reference point. Wonderful stuff!!   Smaller blenders CAN and some DO take the time and effort to do better than a refinery or large bulk blender, like Warren Oil, in improving the "in the can" cleanliness. No I don't have a list but testing could generate that information.    Again, but one of several levers we can pull to improve engine life. The simplest is keeping a clean work station while doing your own oil changes.     

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...