Jump to content

Access Limited Bed Cover

Steve Cornell

Recommended Posts

Steve Cornell Enthusiast

Steve Cornell

Posted
Posted

I just sold my 2003 Silverado HD and kept some of the aftermarket items which includes this cover.

 

This is the "all black" Limited model, this cover was on my truck for 15,000 miles and is like new and comes complete with all the factory paperwork.

 

Fits 1999 and up shortbed Silverados.

 

$350 plus shipping

 

access2.JPG

access1.JPG

Steve Cornell Enthusiast

Steve Cornell

Posted
  • Author
Posted

This is the Access "roll-up" bed cover.

Click here for the Access cover web page

 

This cover rolls up in seconds and takes the supports with as it rolls up, I pulled a 36' gooseneck and it worked great, unhook the trailer and roll the cover closed.

 

It uses a cam lock action to latch the cover and it is VERY tight, no sags at all..

 

This is the "all black" Access Limited version.

  • 3 weeks later...
  • 4 weeks later...

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      OEM Trailer Hitch Receiver - Impact tightened by shop

      By Chuck FB · Posted

      Great info to have, I printed out what you had in your document as well as Newdudes post as I could see this mistake with the hardware happening very often if not realizing what type of special bolts are being used and just guess on bolt size for torque or the good enough "easy" method as per whack in the used bolts with an impact and send it !. 
    • dennismc
      Auto start stop disable

      By dennismc · Posted

      I installed the Auto stop eliminator on my 21 Sierra SLT shortly after I got it. They have a detailed video instruction on how, took me about 20-30 minutes to do. I was apprehensive too to start tearing apart a new truck but it was pretty easy install. Like you mentioned get some trim tools. I went to Harbor freight and picked up a set. If you can find some install videos/instructions to give you and idea for a plan of attack you should be fine.  
    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      If all oil manufacturers had to meet a higher standard for not just the initial filtering of the oil but that they had to improve on their formulation so that the oil cleaned the engine such as the Valvoline R&P or the new Mobil product ( assuming it works similar of course ), and the oil was changed on an interval based on good UOA data, there shouldn't be any gremlins running around like miniture rats on top of your heads to be washed down into the oil pan below 😁 
    • No F-bdy Bs
      Thoughts on these wheels?

      By No F-bdy Bs · Posted

      Worst factory HD wheels GM makes
    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      A while back on another thread there were comments and thoughts on air filters and I know that can tend to be a bit of a hot topic because of outfits that have a vested interest in selling aftermarket air boxes fitted with the gauze type of oiled elements touting the lower air restriction. However and unfortunately I don't know where I have seen the test results in the past about the amount of dirt through a test procedure that these style of filters do pass more dirt through than a properly designed ( not some cheap Chinese knock off ) paper/synesthetic media filter can do. Lake Speed had a conversation on that topic with one of the employees at Donaldson and there seemed to be a consensus of these oiled filters falling short in the absolute percentage of dirt holdback.    Which all ties back into how good the air filter is on the engine at keeping dirt out as that is going to reflect as a contaminant introduced into the oil as well as cylinder wear even if some of that dirt does find its way out of the exhaust rather then the crank case. Put another way that one can throw the kitchen sink at filtering the oil and using a bypass system which I fully expect will do nothing but good for the oils contamination but if the air filter system isn't doing its job then its preventing the engine from reaching the best wear/lasting case scenario instead.    Now perhaps this topic is or isn't for this particular thread but Grumpy Bear or anyone else for that matter, do you have access to some scientific trust worthy testing on engine air filter types to get some proper comparison data to post up.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...