Jump to content

Where is everyone?

General Lee 01

By General Lee 01
in The Off-Topic Bar

Recommended Posts

76BBSub Enthusiast

76BBSub

Posted
Posted

Been painting my garage, getting ready to install some new parts on my Suburban.....

dunno about everyone else...

Dave Enthusiast

Dave

Posted
Posted

Ok, so I only found this site  afew days ago, learned a lot already, need new engine for my 94 4x4 5.7 and was on the performance forum. But now its Sat. nite and they say we can expect 1 to 2 feet os snow in the next 48 hours! So for the second time in this trucks life I have to put chains on tomorrow as I push a 7.5 foot Western plow. Truck has been great and plows great but after 10 inches or more chains are a must. So much for spring in Eastern PA! Hope some of you are enjoying better weather! Wish I could drink a beer & detail the truck instead!

TheScaryGuy Enthusiast

TheScaryGuy

Posted
Posted

Wow today was great, it was like 50degrees F or so.  So I washed all the vehicles with the pressure washer, (Except my truck, it gets a special garden hose treatment)and pulled off the nice wheels to clean'm off and gett'm ready fer summer.  I also had to do some waxing, the trees in the woods left some clear coat scratches, nuttin some Meguiars or 3m wax wont take care of.

MountaineerTom Senior Enthusiast

MountaineerTom

Posted
Posted

It was a crappy day here.  It hasn't stopped raining all day.  I think it's suppose to be the same thing tomorrow.  Can't get outside to do anything.  I could have went mudding, but I didn't feel like cleaning up the mess.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Coastie05
      2027 GMC Sierra: Official Discussion

      By Coastie05 · Posted

      Sure, but they do have some affordable options like the Trax, Trailblazer, Envista, and Encore. Some of these have a cheaper base price than the Civic, though the fuel economy isn’t as high. The main problem is that people WANT the highest trim with all the goodies and finance for like 7 years. That’s how ppl “afford” the more expensive vehicles. 
    • Jsdirt
      07 yukon xl 6.2 stalls at hot idle and wont restart

      By Jsdirt · Posted

      Holy s**t - not much of a parts thrower you say? You BLASTED that thing with the parts cannon!  You'd have been probably $1,000 ahead if you had just brought it to a competent shop rather than shotgunning a bunch of parts it clearly didn't need.   Just FYI - oil additives are really, REALLY good at ONE thing ... and that's emptying your wallet. They're ALL useless gimmicks.   If that has the L94 or L99, then #7 is an AFM cylinder. I'd suspect a failed lifter in that case.   If you leaned on wiring, sensors, and/or connectors while changing the oil, you'll have to check all that to be sure pins didn't get pulled out, connectors broken, etc.. Old wire loom that was barely adequate when new is certainly brittle by year 19 - make sure wires aren't chaffed and shorting out somewhere where you might have leaned. or supported yourself on it.   If your a mechanic, why didn't you just find out what you were missing and troubleshoot from there??  TIMED spark, fuel PSI / injector pulse, air, compression.  Can't make ANY money going the parts cannon route.
    • Jsdirt
      2027 GMC Sierra: Official Discussion

      By Jsdirt · Posted

      LOL! Are you joking?? That wax SUCKS! 100% gimmick made to "look" good.    After just TWO winters I had severe surface rusting in patches over 90% of the frame. Only reason it looks great in the pics is because I SATURATED the frame every single fall with used motor oil for 14 of the 16 years I owned it. Otherwise it would've been sent to the crusher 8 years earlier with the speed it was rusting prior!    I sold that POS 3 years ago. Was a gigantic headache the second it rolled off the showroom floor. Brakes pulsated on the TEST DRIVE. Door trim fell off the 1st week! Interior squeaked and rattled, and the drivetrain clunked after 2k miles. 4x4 switch failed shortly after. Front end - ball joints, struts, hub bearings - all failed between 38k-50k. Engine started burning oil at 50k. Rear and and transmission failed before 100k. Nothing but problems, and frustration with the piss-poor engineering designed to make you give up. Well, it worked! Nothing on that truck was easy to remove ... except the wheels. They haven't figured out how to screw that up yet. Give 'em time ...   I won't make that mistake again. EVER.   Such fond memories ... https://postimg.cc/K1qf23tS  https://postimg.cc/gallery/X02z64J  https://postimg.cc/gallery/mHSRXZv  https://postimg.cc/gallery/D4mMRfL
    • davester
      OBD not ready?

      By davester · Posted

      Different monitors do their test only under conditions specific to that monitor.  you MIGHT find the drive cycle conditions for the monitor that isn't ready on this site: https://lemon-manuals.la/   If it's not there, then it should be on alldata.com for your truck, but it requires a paid subscription.   And you need to know which specific monitor isn't ready.
    • RW2018GMC
      Me too……..

      By RW2018GMC · Posted

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...