Jump to content

Anybody disabled their foo-foo lights?


Recommended Posts

Posted

I used to have a 2002 GMC Z71 with power locks. The power lock switch (or the remote) just locked the doors and turned on the dome light. Ok, cool, I see the value in that.

 

But on my 2005 Silverado, some GM engineer decided to "improve" that. Now when I lock the doors when it's dark, I get the DRL's and backup lights. This happens regardless of whether I use the power door lock switch, or the remote.

 

This new "improvement" is idiotic. It sends a flood of light--waay too bright--outward from the front and the back of the truck, but leaves those steps between the door and the front or back of the truck even more treacherous, because the distant bright light blinds me to the still unlit area around the door, where I am!

 

I just want to lock the doors. I don't need some idiot shining a bright light in my face. Is there a way to rescind this ill advised monument to some foo-foo engineer's errant sensibilities? It's so stupid it's embarassing!

Posted

You take creative writing? That's a very well-worded post. I would assume there has to be a relay or fuse somewhere that's controlling that crap. Have you tried searching the forums? I'm sure somebody's discussed the same thing before.

Posted
You take creative writing?  That's a very well-worded post.  I would assume there has to be a relay or fuse somewhere that's controlling that crap.  Have you tried searching the forums?  I'm sure somebody's discussed the same thing before.

 

 

 

I searched for +disabled +lights. Only about 6 hits, none were for this. That search engine is almost as busted as the garage. Takes about 10 tries to get it to work.

Posted

Does your truck have the DIC? If so, I'm pretty sure this is a customizable function, in which case it could just be turned off.

...Something like:

LOCK FEEDBACK ---> HORN ---> LIGHTS ---> BOTH

 

...it's nice to read a well-worded post--although I'm sure black1500 meant his comment as a compliment also.

 

Anyways, I hope this helps. If you don't have a DIC, then I don't know how to help you.

 

Good luck :fume:

Posted

Yea...the DIC has all the information but if you dont have that, then I believe you can overide it like in the older ones. Check the manual...Maybe...

Posted
Yea...the DIC has all the information but if you dont have that, then I believe you can overide it like in the older ones.  Check the manual...Maybe...

 

 

 

Ok, I'll check tomorrow and report back on whether it offered a solution. Thanks to all who replied!

Posted

Oops. Should have put something like:

LOCK FEEDBACK ---> NONE ---> HORN ---> LIGHTS ---> BOTH

 

...seems like I would've remembered to include the 'NONE' option, since that's what you're probably going to want to select.

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.6k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    343,007
    Total Members
    8,960
    Most Online
    Brendan C
    Newest Member
    Brendan C
    Joined
  • Who's Online   2 Members, 0 Anonymous, 1,117 Guests (See full list)

  • Latest Articles

  • Posts

    • The oil filter has NOTHING To do with oil leak. GM sources parts from 1,000's of vendors and as with anything mass produced, flaws are unavoidable.    Putting a larger oil filter will do nothing but satisfy emotions. The OEM filter is designed for the engine and perfectly capable of handling the demands on the engine. Oversize oil filter could result in reduced flow and overall lower oil pressure.
    • You're better read than that Atlas. 😏   British science fiction writer Arthur C. Clarke formulated three adages that are known as Clarke's three laws, of which the third law – that "any sufficiently advanced technology is indistinguishable from magic" – is the best known and most widely cited.   Stribeck and the pivotable Hersey Number isn't voodoo nor snake oil. That part is physics. It's what marketing and bean counters do with it that is snake oil and voodoo.    Stribeck is the relationship between Hersey and the Coefficient of Friction. Within the Hersey Equation if viscosity and viscosity is 'Dependent' on.......heat.......and.......viscosity index or the temperature to viscosity slope.    Specifically Hersey is the viscosity AT THE TEMPERATURE IN THAT LOCATION FOR THAT SLOPE.   Hydrodynamic lubrication exist when the film thickness in the location is 3X the Ra roughness of the surface. This is irrespective of the hardness of the substrate. To obtain that thickness X viscosity is required for Y velocity at Z load. That's a lot of moving parts. It is also impossible to maintain in an ICE but nearly possible with a turbine under constant load.    What does that mean? Error heavy and operate light. Wear is inevitable but the rate of wear and the milage obtainable are a function of prevailing conditions and HABITS. The only penalty is viscous drag and at fractions so low as to be well worth the effort. Double the life, half the manufacturing carbon foot print. Greed is the only impediment.    The materials generated by SwRI are the RESULT not an estimation or a hypothesis.    Don't delude yourself sir, EV's have as many pitfalls as ICE's. We just don't know what they are yet and it will take longer to sort as MARKETING and GREEDY CEO's have had more time to polish the turd they are selling. 
    • You can always count on greed to prey on ignorance and stupidity.    Friend bought a 2019 Ford Flex and asked me about using Valvoline R&P 5W30 in it. Told him give the miles on it and the fact it wasn't yet using oil that it was a good plan. He uses a Valvoline quick change shop for his oil service.   First they tell him that isn't the oil the OEM recommends. He told them he didn't care what the OEM thought. Then they floated the, "But it will void your warranty"    His reply was it's a 2019, there is no warranty and informed them their knowledge of the law was lacking.    Then they tell him 'But it will ruin your motor"!.    Mine to ruin he says. Finally they give in and charge him 150% the semi-syn price    Point it the brainwash is so embedded that even the service industry is drunk on their swill. The public is right behind them. Echoing the same lies on every forum and media platform. If the end goal is indeed EV then I'd say that ship is about built. 
    • Diesel hit $6.00 here today at the truck stop.   Payed $2.79 for E85 today too.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...