Jump to content

2007 Gmc 2500hd 6.0 Vibration


chevz7194

Recommended Posts

Posted

Just bought a new 2500HD 4x4 new style and it has a vibration when going 30mph and you give it about 1/2 throttle. Vibration can be felt and heard on the right side of the cab and last only 1-2 seconds before stopping. You can feel or hear the vibration only when going around 30mph and accelerating as described above. Dealer can't find anything wrong. Any ideas or service bullitens that anyone knows about?

Posted
Just bought a new 2500HD new style and it has a vibration when going 30mph and you give it about 1/2 throttle. Vibration can be felt and heard on the right side of the cab and last only 1-2 seconds before stopping. You can feel or hear the vibration only when going around 30mph and accelerating as described above. Dealer can't find anything wrong. Any ideas or service bullitens that anyone knows about?

THIS MAY HELP YOU. :chevrolet: ALSO SINCE YOUR TRUCK IS SO NEW IT MAY TAKE THEM A WHILE TO HAVE A FIX

 

Document ID# 1991701

2007 Chevrolet Silverado - 2WD

 

 

999999995.gifSubject:Abnormal Noise And Or Vibration While Driving - keywords accessory aftermarket axle body boom buzz case grown growl howl moan modification no OEM part prop rattle resonance shaft transmission whine #PIP3140B - (06/22/2007)

 

 

 

 

 

 

Models:2008 and Prior Passenger Cars and Light Duty Trucks including Saab and Saturn

 

 

 

 

This PI was superseded to update Model Years. Please discard PIP3140A.

 

The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.

 

<A href="http://service.gm.com/servlets/BlobShtml?ShtmlFile=1991701&psdid=1647&evc=sm#ss1-1991701">

Condition/Concern:

Some customers may notice a noise or a vibration in their vehicle that seems to be abnormal and may not have been there when the vehicle was new. Comparison of the customer vehicle noise and/or vibration levels with another vehicle of the same make and model may reveal that the customer's vehicle may have a higher level of noise and/or vibration.

 

<A href="http://service.gm.com/servlets/BlobShtml?ShtmlFile=1991701&psdid=1647&evc=sm#ss2-1991701">

Recommendation/Instructions:

The first step in diagnosis of a concern of this nature is to evaluate the customer vehicle for any aftermarket accessories. The mounting or location of some of these items are designed for convenience and many times do not take into consideration the negative effects they may have with air flow over and around the vehicle and also noise transfer paths when the item is located between two isolated components. For example, the popular "step bars/nerf bars" that contact both the frame of the truck and the cab without any type of insulation are a noise transfer path of a normally operating drivetrain into the passenger area of the vehicle. Some other known contributors to noise and vibrations are running boards, bug shields, sun visors, vent shades, emergency lights, custom grilles, ski racks, bicycle racks, etc... Removal of these items, while many times not popular with the customer, is necessary in order to evaluate whether they contribute to the customer's concern.

 

Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.

 

 

 

GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information.

999999994.gifWE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION

© Copyright General Motors Corporation. All Rights Reserved.

 

 

Posted
Forgot to mention that the sound and vibration seem to be coming from behind the glove box or behind the firewall in that area? Just FYI

 

HERE YOU GO BUD. YOUR WELCOME

Subject:Buzz Rattle Flutter Noise From Right Side Of Dash - keywords fill front information instrument panel rattle transmission tube vibrate vibration #PIT4352A - (06/19/2007)

 

 

 

 

Models:2007-2008 Cadillac Escalade, ESV, EXT

 

 

2007-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe

 

 

2007-2008 GMC Sierra, Yukon, Yukon Denali, Yukon XL, Yukon Denali XL

 

 

 

 

This PI was superseded to update model years. Please discard PIT4352.

 

The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.

 

<A href="http://service.gm.com/servlets/BlobShtml?ShtmlFile=1990291&psdid=1647&evc=sm#ss1-1990291">

Condition/Concern:

Some customers may comment on a buzz, rattle, or flutter type noise coming from the front of dash on the passenger side of vehicle

 

This may be caused by a lack of clearance between the transmission fill tube and the aux heater hose return line running behind the fill tube on vehicles equipped with rear heat. Or lack of clearance between the transmission fill tube and the front of dash/cowl.

 

<A href="http://service.gm.com/servlets/BlobShtml?ShtmlFile=1990291&psdid=1647&evc=sm#ss2-1990291">

Recommendation/Instructions:

The noise can be eliminated by creating a gap between the transmission oil fill tube and the rear heater return line/front of dash by adjusting the fill tube.

 

Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.

 

 

 

GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information.

999999994.gifWE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION

© Copyright General Motors Corporation. All Rights Reserved.

 

 

Posted
Forgot to mention that the sound and vibration seem to be coming from behind the glove box or behind the firewall in that area? Just FYI

 

HERE YOU GO BUD. YOUR WELCOME

Subject:Buzz Rattle Flutter Noise From Right Side Of Dash - keywords fill front information instrument panel rattle transmission tube vibrate vibration #PIT4352A - (06/19/2007)

 

 

 

 

Models:2007-2008 Cadillac Escalade, ESV, EXT

 

 

2007-2008 Chevrolet Avalanche, Silverado, Suburban, Tahoe

 

 

2007-2008 GMC Sierra, Yukon, Yukon Denali, Yukon XL, Yukon Denali XL

 

 

 

 

This PI was superseded to update model years. Please discard PIT4352.

 

The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.

 

<A href="http://service.gm.com/servlets/BlobShtml?ShtmlFile=1990291&psdid=1647&evc=sm#ss1-1990291">

Condition/Concern:

Some customers may comment on a buzz, rattle, or flutter type noise coming from the front of dash on the passenger side of vehicle

 

This may be caused by a lack of clearance between the transmission fill tube and the aux heater hose return line running behind the fill tube on vehicles equipped with rear heat. Or lack of clearance between the transmission fill tube and the front of dash/cowl.

 

<A href="http://service.gm.com/servlets/BlobShtml?ShtmlFile=1990291&psdid=1647&evc=sm#ss2-1990291">

Recommendation/Instructions:

The noise can be eliminated by creating a gap between the transmission oil fill tube and the rear heater return line/front of dash by adjusting the fill tube.

 

Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.

 

 

 

GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information.

999999994.gifWE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION

© Copyright General Motors Corporation. All Rights Reserved.

 

 

 

 

 

ill give it a try thanks man

Archived

This topic is now archived and is closed to further replies.

  • Latest Articles

  • Posts

    • You can install tailpipes that direct the exhaust sideways vs the OEM one that goes straight back. There are several on the market, do you own research. HOWEVER, you need to make sure the Venturi vents are still intact, otherwise it will throw a engine code. There is a sensor somewhere that detects back pressure on the exhaust. And if it doesn't collect the correct metrics, it will throw the truck into limp mode. 
    • "Teardown" is complete. Head surfaces are clean and ready, new intake is prepped and ready. Coolant drained and water pump is removed, radiator is removed, new hoses and pump are ready.   The replacement intake is also from a '95 (with I think 260k, the odometer said). Noticeably less pitting where it covers the rear coolant passages. I'm not sure if that's a tribute to more frequent use, more frequent coolant changes/upkeep, or if the intake was machined at some point. But it appears I found a good one.   My coolant hoses were original, and the lower hose still retained the factory spring inside. It's not really rusty, but it's got deposits all over it. Unsure if I should re-install it (will thoroughly clean it first). Someone said hose technology has gotten better since 1995 (has it?) and I don't need the spring. I think modern EPDM is what made those hoses last from 1995-2026, so it's a question of how much suction can the water pump really pull, and will it collapse the hose without a spring?   I'm stopped and waiting for parts, however.   When I first brought the truck home, the fan was intermittently hitting the radiator shroud. I could see someone had monkeyed with the shroud (put a bunch of cardboard as a spacer between the upper/lower shroud halves. Someone said the motor mounts have likely failed and the engine has sagged. I wasn't sure I believed that. The engine is really solid in its mounts: To remove the old intake I *just* nearly permanently welded to the heads with freshly cured RTV and gasket snot two weeks ago, I literally had to use the arms on my lift and a chain with a bolt attached to the intake to pull it loose. It almost picked the front of the truck off the ground before ....scuuuuuuuuuuup.... I could actually hear the gaskets tearing and it broke loose and the whole truck settled back down. Motor barely moved.   SO, those parts I'm waiting on... The lower radiator mounts/bushings had completely failed. The radiator needs to be insulated from the rad support, and the bushings help the rad stand at the correct height. The plastic "baffle" was also destroyed at some point. Someone had attached the shroud to it incorrectly, overlapping a joint that should have been underlapped, creating another suspect issue potentially causing things to hit the fan. Broken tabs, side is busted off, and it's perma-formed/bent where it was jimmied incorrectly.   The baffle? Unobtainum. Long since discontinued from GM, of course. Aftermarket/capa/chinese? Also unobtanium. In GM's infinite wisdom, it appears there are at least two different variations whether the Blazer is 2 or 4 door, and I can't yet tell if they shared the same part with the S-pickups. Plan B, if I can't find a viable used one, will be to create a bracket to re-assemble the critical joint I need to seal a gap with the shroud. But that will bug me, it won't be...perfect.   The water pump bolts appear to have been installed with...plumber's putty. I guess, sure, if it works...? I've found a few "backyard fixes" like that. Someone's been here before....   If I can't find someone to jam bamboo under my fingernails to fill my free time this week I think I'll install the driver's power window motor and replace the rear door speaker that's inop. I've got a genuine GM "9.5" ohm working replacement. Why GM used a non-standard resistance....nevermind. Of course they did, you can get more sound from a cheap factory amp that way.   And the saga goes on...
    • // Thank you, also for your  response. More information is always good. This 2013 GMC is most likely my 'forever truck"-I'm 77 and retired...and truck only has 42K on it-very clean-so I try to keep it that way.  Tks again for your  response- glenn
    • I started my install this weekend. Everything was pretty straight forward but I ran into one issue with running power through the firewall. The nipple grommet on my High Country already has a small harness running through it - has anyone else ran into this issue? And on the engine bay side, does the wire basically just penetrate the factory wiring boot? I did this on my '22 Trail Boss and it seems much easier but thats been a few years. My other thought would be possibly drilling a new hole adding a rubber grommet just to the lower left of the factory hole. Thoughts?   Has anyone used a T-harness off the Bose amp and obtained power from there? It seems a little odd that such a small amp needs 3 power leads
    • ///// Ok--Thanks for that info--I could not find yesterday when I looked for the specs on that NAPA filter what I wanted. Their website is not very user friendly. I buy all teh filters for  our three vehicles once or twice a year. Have always run NAPA Gold on everything I own....I buy it thru my Son's account for his business-which he has a Heavy Equipment repair shop-one reason he uses NAPA so much-they have such a full line of coverage for just about anything/anywhere- He gets s  good discount because of volume bought. Anyway-Thank you -Sir for your response.   glenn
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...