Jump to content

Be honest now.....


antig24

Recommended Posts

Posted

Is it just me or does anyone else try to break into the ADMIN FORUM????!!!!  Come on now......BE HONEST....I gotta know what these guys could POSSIBLY post over 700 messages about!!! Gotta be some priceless discussions in there!! hmmmmmm.......I 'll keep trying.

Guest Friz
Posted

You have to give Mervz ?. That's what it cost me. Now I can party with the best. I feel like my life has really taken off since I joined the GM-TC Moderator Club!

This is a parody and not to be taken seriously.

Posted

I tried to break in one time.  Apparently Mervz felt the need to ban me from my moderator positions as a joke one day.  I knew nothing about it and couldn't get into the admin forum, so I tried to break in.  LOL

btw, with the group of moderators we have on this site, the discussions in there are not very exciting.  Not including what I post, of course.   ;)

Posted

LIERS LIERS LIERS..... theres GOT to be good stuff in there.....come on now....704 posts!?!?!  Probably have pictures of an 18 year old Suburban wearing NO PAINT...

Posted

.......like this in the regular forums so I do it in the Admin Zone.

Heck, I wouldn't have anything else to say cause nobody has posted anything in my Section in 3 weeks.

 

Posted

To be truthful....

There are pictures of my 25 year old suburban...with lot's of paint....

but anyone can see them at my web site....

wanna hear about my new "used" 40 gallon gas tank...become a moderator!!

Jeff

P.S.  Or go see the Classic Forum

P.S.S.  All Suburbans have good paint!!

Posted

Poor Jeremy....just like the Maytag repairman,,,,no posts in weeks!! I told Tom I would post some of my truck since I got a couple of little add ons and some Zaino.  Took some but they didnt come out too good. The black Westins are hard to see on my black driveway.  If it ever stops raining I am going to find a concrete drive and take some.....hopefully tomorrow......hey, I do have one of my neighbor taking the bra off his Audi!! Will that work?  The other mean old Moderators (read that as MERVZ) will think its too risque and probably edit it by putting some of those dots over the headlights and move it over to the top secret Admin Zone for their viewing pleasure only!..........

(Edited by NewbieZ71 at 12:33 am on May 26, 2001)

Posted
Quote: from NewbieZ71 on 11:23 pm on May 25, 2001

The other mean old Moderators (read that as MERVZ)

 

I'm not a Moderator, i'm an Administrator. :biggrin:

Posted

General, that means that you, as a member as well as moderator, will be paying ? for every one of your "lets get ahead of Mervz" posts??????? :shocked:

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.6k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    343,007
    Total Members
    8,960
    Most Online
    Brendan C
    Newest Member
    Brendan C
    Joined
  • Who's Online   1 Member, 0 Anonymous, 885 Guests (See full list)

  • Latest Articles

  • Posts

    • You're better read than that Atlas. 😏   British science fiction writer Arthur C. Clarke formulated three adages that are known as Clarke's three laws, of which the third law – that "any sufficiently advanced technology is indistinguishable from magic" – is the best known and most widely cited.   Stribeck and the pivotable Hersey Number isn't voodoo nor snake oil. That part is physics. It's what marketing and bean counters do with it that is snake oil and voodoo.    Stribeck is the relationship between Hersey and the Coefficient of Friction. Within the Hersey Equation if viscosity and viscosity is 'Dependent' on.......heat.......and.......viscosity index or the temperature to viscosity slope.    Specifically Hersey is the viscosity AT THE TEMPERATURE IN THAT LOCATION FOR THAT SLOPE.   Hydrodynamic lubrication exist when the film thickness in the location is 3X the Ra roughness of the surface. This is irrespective of the hardness of the substrate. To obtain that thickness X viscosity is required for Y velocity at Z load. That's a lot of moving parts. It is also impossible to maintain in an ICE but nearly possible with a turbine under constant load.    What does that mean? Error heavy and operate light. Wear is inevitable but the rate of wear and the milage obtainable are a function of prevailing conditions and HABITS. The only penalty is viscous drag and at fractions so low as to be well worth the effort. Double the life, half the manufacturing carbon foot print. Greed is the only impediment.    The materials generated by SwRI are the RESULT not an estimation or a hypothesis.    Don't delude yourself sir, EV's have as many pitfalls as ICE's. We just don't know what they are yet and it will take longer to sort as MARKETING and GREEDY CEO's have had more time to polish the turd they are selling. 
    • You can always count on greed to prey on ignorance and stupidity.    Friend bought a 2019 Ford Flex and asked me about using Valvoline R&P 5W30 in it. Told him give the miles on it and the fact it wasn't yet using oil that it was a good plan. He uses a Valvoline quick change shop for his oil service.   First they tell him that isn't the oil the OEM recommends. He told them he didn't care what the OEM thought. Then they floated the, "But it will void your warranty"    His reply was it's a 2019, there is no warranty and informed them their knowledge of the law was lacking.    Then they tell him 'But it will ruin your motor"!.    Mine to ruin he says. Finally they give in and charge him 150% the semi-syn price    Point it the brainwash is so embedded that even the service industry is drunk on their swill. The public is right behind them. Echoing the same lies on every forum and media platform. If the end goal is indeed EV then I'd say that ship is about built. 
    • Diesel hit $6.00 here today at the truck stop.   Payed $2.79 for E85 today too.
    • Thanks for posting, I'm sure it will help someone
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...