Jump to content

2007 Silverado Wont Start After Installing Ignition Switch

rmmotocrosser4
 Share

Recommended Posts

rmmotocrosser4 New Member

rmmotocrosser4

Posted
Posted

Hey everyone I installed an ignition switch in my 2007 silverado new body and now it wont start is their some type of relearn procedure that I'm suppose to follow. It started before I installed it but sometimes it wouldnt before the installation. I also installed a new starter and battery.

Duelin Enthusiast

Duelin

Posted
Posted

Did you replace the ignition switch or the ignition lock cylinder? If it was the ignition lock cylinder You might want to try the following relearn sequence. I found this on another site. So I don't know if it will work for you not. But it is worth a try.

 

 

1.Turn ON the ignition, with the engine OFF.

2.Attempt to start the engine, then release the key to ON, vehicle will not start.

3.Observe the SECURITY telltale. After approximately 10 minutes, the telltale will turn OFF.

4.Turn OFF the ignition, and wait 5 seconds.

Repeat steps 1 through 4 two more times for a total of 3 cycles/30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK.

Important: The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.

Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password.

With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles.

  • 4 years later...
spunkerg New Member

spunkerg

Posted
Posted

Check the starter fuse. I had the same issue, wound up blowing a fuse. It ran, changed out the ignition switch and could not get it to crank. I would up be a fuse. I was getting a 1682 code, which I thought was because of the bad ignition switch, but what I found after changing the ignition switch and still getting the error was a bare wire in the wiring harness above the emergency brake.

 

 

  • 5 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,962
    Total Members
    8,960
    Most Online
    contrabombarde
    Newest Member
    contrabombarde
    Joined

  • Who's Online   2 Members, 0 Anonymous, 1,121 Guests (See full list)

  • Latest Articles

  • Posts

    • jgaudet99
      Tire psi

      By jgaudet99 · Posted

      Thanks for all the help so far!   I did try right from 2026 right down to 2021, and only from 2023 down lets me select the option for tire psi change, but I get the vehicle not supported error!   I'll definitely try it under Chevrolet after work today, and I'll get the sensor number from gm for my truck tire sensors. And I'll let you know if it works for me under Chevrolet!   And if that doesn't work, I'm going to guess that what @Atlas said about maybe I have a different body control module could be true!  
    • Jsdirt
      2010 Avalanche 5.3 not running correctly after engine swap.

      By Jsdirt · Posted

      From where I'm sitting this sounds like a compatibility problem. I'm assuming the 2007 was a 900-series truck, and not an 800-series (they were sold side-by-side in dealerships that model year), since it starts and runs.   This is why I HATE post-2006 vehicles. Everything becomes a huge problem when you try to keep the thing running for longer than the manufacturer has designed it to.    I can't remember when Global-A architecture started - either '10 or '11. For your sake, you had better hope it's '11, or you're going to be spending some BIG money to correct this cluster-eff. That's something you need to find out before doing anything else. You may have several computers bricked ... but the fact that it runs tells me you MIGHT be ok here.     EDIT: Just did a quick refresher. You're screwed. This is Global-A. The 2 systems are NOT compatible in the slightest. Once you get the correct engine in there that IS compatible, you're going to need to see how many computers are locked. Absolute NIGHTMARE to straighten out, too. Your buddy might be better off cutting his losses and finding something else.   Welcome to post-2006 vehicle electronics. This is why I quit the industry, and drive nothing built after 1994. This stuff takes all the fun out of wrenching!  
    • bwiese
      Show Us Your 2019 & Up T1 Pictures !

      By bwiese · Posted

      Recently acquired new 2026 Silv. 1500 WT  - L3B + 4WD,  std cab + std bed, in (duh!) Sierra White. Upgrades: replaced 'steelies' w/  Vision "Flow" black alloys,  17x8.5"; HDX nerf bar w/steps (black powdercoat); Weatherguard large/deep alloy saddle toolbox; Michelin fitted bedmat (sale, perfect fit) Weathertech door sill guards TBD: rear wheebox liners 4x black fender arch trim - searching for best  (Putco: chrome only; not looking for flares either!) -Bill    
    • Chuck FB
      Tire psi

      By Chuck FB · Posted

      True, hard to say what differences there may or may not be between Chev and GM as well as a production year or mid year part change either.    I just found it odd that under the Sierra choice on the Autel that many of the last few years of production year did not include the choice of changing the tire pressure but if that is an Autel thing or a GM thing as to why the choices were not there. Knowing what tpms sensors are on the truck should give some guidance into which choices on the tool even make sense to try as I wouldn't give up just yet with the tool but I guess he will see what if anything he comes up with if he finds out a bit more info and tries a few more things on the Autel. 
    • davester
      Needing this part.

      By davester · Posted

      I'm sure if you went to a junkyard where you go in and pull the part off the truck yourself, not a used part place where they do it for you, you can get that part on it's own.  Depending on if and what else you would be buying, and time of day, they might even just skip over adding it as a item to the bill.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...