Jump to content

HID Install

acronate

Recommended Posts

acronate Enthusiast

acronate

Posted
Posted

Hey guys new to the forum!!! Just picked up a 2015 silverado LT allstar edition and went to go install a set of HIDS and noticed a possible issue. The driverside had a large twist cap to gain assess to the headlight bulb. When you guys are doing the install are you drilling a whole and running a the holes through it or leaving it off completely?

 

Thank you very much and will start another thread with pictures of the truck and plans for it.

Thanks guys!

acronate Enthusiast

acronate

Posted
  • Author
Posted

If its a lt you're going to have reflectors. Unless you do a projector retrofit you're going to want to avoid HIDS.

 

What do you mean I will have reflectors?

 

I know it wont be as good as if I have projectors installed but will still be much better than the factory lighting.

Huetatos Enthusiast

Huetatos

Posted
Posted

 

What do you mean I will have reflectors?

 

I know it wont be as good as if I have projectors installed but will still be much better than the factory lighting.

The headlight housing comes with reflectors on non ltz+ models. It'll be better for you but you'll be blinding everyone on the opposite side of the road. It is illegal and you want to avoid that.

  • 3 weeks later...
Boogie651 Enthusiast

Boogie651

Posted
Posted

While this is for a Sierra. You can see what I did in regards to the dust caps.

 

 

Hey Fondupot,

 

I noticed in the video you said the dust caps were about $5 a piece? You know where I can find them for around that? Cheapest I could find them for was $30 :help:

fondupot Senior Enthusiast

fondupot

Posted
Posted

 

Hey Fondupot,

 

I noticed in the video you said the dust caps were about $5 a piece? You know where I can find them for around that? Cheapest I could find them for was $30 :help:

I was guesstimating. $30 ain't bad tho

 

 

Sent from my iPhone using Tapatalk

Boogie651 Enthusiast

Boogie651

Posted
Posted

I was guesstimating. $30 ain't bad tho

 

 

Sent from my iPhone using Tapatalk

Not bad no, but a $60 mistake.when my buddy went to drill them he used a 1 1/8 hole saw. Way to big for my liking unfortuantely

fondupot Senior Enthusiast

fondupot

Posted
Posted

Not bad no, but a $60 mistake.when my buddy went to drill them he used a 1 1/8 hole saw. Way to big for my liking unfortuantely

Ah that's rough. Sorry dude

 

 

Sent from my iPhone using Tapatalk

Boogie651 Enthusiast

Boogie651

Posted
Posted

Ah that's rough. Sorry dude

 

 

Sent from my iPhone using Tapatalk

Live and learn i guess lol.

thanks for the video btw. pretty much walked me through my install because the TRS directions suck.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.6k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    343,007
    Total Members
    8,960
    Most Online
    Brendan C
    Newest Member
    Brendan C
    Joined

  • Who's Online   0 Members, 0 Anonymous, 972 Guests (See full list)

    • There are no registered users currently online

  • Latest Articles

  • Posts

    • Grumpy Bear
      Joke Thread

      By Grumpy Bear · Posted

    • Grumpy Bear
      The Peckish Synapse

      By Grumpy Bear · Posted

      You're better read than that Atlas. 😏   British science fiction writer Arthur C. Clarke formulated three adages that are known as Clarke's three laws, of which the third law – that "any sufficiently advanced technology is indistinguishable from magic" – is the best known and most widely cited.   Stribeck and the pivotable Hersey Number isn't voodoo nor snake oil. That part is physics. It's what marketing and bean counters do with it that is snake oil and voodoo.    Stribeck is the relationship between Hersey and the Coefficient of Friction. Within the Hersey Equation if viscosity and viscosity is 'Dependent' on.......heat.......and.......viscosity index or the temperature to viscosity slope.    Specifically Hersey is the viscosity AT THE TEMPERATURE IN THAT LOCATION FOR THAT SLOPE.   Hydrodynamic lubrication exist when the film thickness in the location is 3X the Ra roughness of the surface. This is irrespective of the hardness of the substrate. To obtain that thickness X viscosity is required for Y velocity at Z load. That's a lot of moving parts. It is also impossible to maintain in an ICE but nearly possible with a turbine under constant load.    What does that mean? Error heavy and operate light. Wear is inevitable but the rate of wear and the milage obtainable are a function of prevailing conditions and HABITS. The only penalty is viscous drag and at fractions so low as to be well worth the effort. Double the life, half the manufacturing carbon foot print. Greed is the only impediment.    The materials generated by SwRI are the RESULT not an estimation or a hypothesis.    Don't delude yourself sir, EV's have as many pitfalls as ICE's. We just don't know what they are yet and it will take longer to sort as MARKETING and GREEDY CEO's have had more time to polish the turd they are selling. 
    • Grumpy Bear
      The Peckish Synapse

      By Grumpy Bear · Posted

      You can always count on greed to prey on ignorance and stupidity.    Friend bought a 2019 Ford Flex and asked me about using Valvoline R&P 5W30 in it. Told him give the miles on it and the fact it wasn't yet using oil that it was a good plan. He uses a Valvoline quick change shop for his oil service.   First they tell him that isn't the oil the OEM recommends. He told them he didn't care what the OEM thought. Then they floated the, "But it will void your warranty"    His reply was it's a 2019, there is no warranty and informed them their knowledge of the law was lacking.    Then they tell him 'But it will ruin your motor"!.    Mine to ruin he says. Finally they give in and charge him 150% the semi-syn price    Point it the brainwash is so embedded that even the service industry is drunk on their swill. The public is right behind them. Echoing the same lies on every forum and media platform. If the end goal is indeed EV then I'd say that ship is about built. 
    • CamGTP
      Gas Prices

      By CamGTP · Posted

      Diesel hit $6.00 here today at the truck stop.   Payed $2.79 for E85 today too.
    • richard wysong
      Electrical Problem - solved

      By richard wysong · Posted

      Thanks for posting, I'm sure it will help someone

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...