Jump to content

Recommended Posts

Posted

As stated, truck sounds like it has an exhaust leak around 1500 RPM right before down shift, V8 mode. The radio has to be off to hear it, and now i'm tuned into it so I always hear it. Dealer said it was fuel pump, I'm not buying it having had many fords with leaking manifolds. Has anyone run across this issue/sound?

Posted (edited)

Flapper valve in the exhaust possibly? I don't notice any noise like that in my 15, but maybe I'm just not noticing it

Edited by GsBowtie
Posted (edited)

Good possibility. I was told that it was the fuel pump, and that they are quiet when you buy the truck but get louder.

 

So I guess the question is, does anyone have a loud "fuel pump"

Edited by derailed
Posted

Did the dealer attempt to fix it? I noticed a whistling noise when I have the windows down. It starts about 1800 rims in 2nd gear under acceleration. It gets higher pitch as rpms increase.

Posted

No they didn't... They gave me the old hand on the back let me show you to the door "it's all ok sir".. Who has time to argue with someone who doesn't know the difference between a nut and bolt.

 

Just haven't had the time for a second opinion. I looked myself and didn't see any carbon showing anywhere, but I'm highly skeptical of their diagnosis.

Posted

I assure you this truck didn't make that noise when I bought it. The dealer told me it gets louder after you put some miles on it.

  • 2 weeks later...
Posted

This sounds like my problem as well. If we are hearing the same noise, I can attest to how annoying it is. the dealer has replaced my fuel lines, fuel pump and still haven't fixed it. i said for day one it sounds like an exhaust leak but they are the experts.

 

See this tread and see if it sounds familiar.

 

http://www.gm-trucks.com/forums/topic/188701-engine-tick-2015-gmc-sierra-53/page-4?do=findComment&comment=1851252

  • Like 1
  • 4 years later...
Posted

I’m convinced it’s the ball and socket connection on the Y pipe to the header/manifold. The passenger side doesn’t have that connection and I do t hear anything from that side whatsoever. I’ve done Hooker Blackheart header on my 2018 5.3 and am about to cut/weld the Y pipe on driver side to make a connection exactly like the passenger side. 💯 it will fix the exhaust leak problem everyone is experiencing 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,915
    Total Members
    8,960
    Most Online
    ChristopherDobson
    Newest Member
    ChristopherDobson
    Joined
  • Who's Online   0 Members, 0 Anonymous, 1,087 Guests (See full list)

    • There are no registered users currently online
  • Latest Articles

  • Posts

    • Monthly payment is only part of the equation. With today's prices and interest rates, I'd look at the total monthly cost: payment, insurance, registration, fuel, maintenance, and expected repairs. A vehicle that fits comfortably into your budget is usually the better choice than stretching for a higher trim. I've also kept my vehicles longer over the past few years. New cars have gotten expensive enough that driving one for 10+ years, while staying on top of maintenance, often ends up being the most cost-effective approach.
    • 10 Ford and Chevy engines proven to reach 300,000 miles   You may note a common 3K OCI on this list of gas motors. I skipped over the diesels. Dh'O. 
    • Thanks newdude!  By the time manual selection is needed, I'm probably too much of a control-freak to depend on the transmission sensing braking to activate automatic downshifting.  I would be anticipating the situation and already be manually downshifting.   This truck replaced a 2004.5 LLY diesel with the Allison 5-speed.  Putting it in T/H made noticeable differences (when the torque converter locked, upshift points, downshift behavior).  On this 2024 gasser with the 10L1000 I haven't been able to detect much, if any, difference.  Ok, I can never tell now when the torque converter locks up.  But I also don't notice differences in shifting.  For downhills, I've probably already manually downshifted by then anyway.  Since it's also more awkward (than the 2004.5) to engage/disengage I don't even bother.  Or maybe it doesn't really matter with just a 3k lb. camper in the bed?   Thanks also for the list of reasons the charging system might select various voltages.  However, what I am seeing doesn't fall into any of those categories.  It very definitely, and very consistently, rises after coasting/braking.  Maybe not immediately, but not very long after coasting/braking.  Very consistently drops voltage when no longer coasting/braking.  It might also be interacting with the camper battery charging (I might disconnect the camper and see if it changes the charging behavior).  I also need to recheck turning on headlights for when I want to force it to charge the camper.   Another JR, in June I converted the camper to LiFePO4.  Since it's not a good idea to try to charge lithiums directly using truck, I installed a Victron Orion XS DC-DC charger (which BTW is AMAZING!!).  Being cheap, I only had to buy that one item (besides the battery, of course) to do the conversion.  The camper OEM 120v battery charger (only 19 years old and works perfectly) and the truck feed the input to the DC-DC charger (not at the same time).  But I didn't want the camper charger feeding back to the truck so I kept the old separator.  I considered replacing the separator with a 30amp diode but that means more work and might add another 1/2 volt drop.  One thing that surprised me was the voltage drop over the long 10awg wire run, so I can only charge smoothly at 8 amps (because the DC-DC charger is completely configurable).  Another reason I don't want an added voltage drop with the diode.  I might also be a little lazy but all this work is being done under the sink with a small cabinet opening.    
    • apparently CA smog is (or at least was)  checking that the vehicle is using the oem and/or a ca smog approved tune, so I expect you'll fail inspection doing it.
    • yes, leaking exhaust will mess up o2 sensor readings, which in turn messes up fuel trims.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...