Jump to content

New water pumped installed and now there is a squeal

PBaltes

Recommended Posts

PBaltes New Member

PBaltes

Posted
Posted

I replaced the water pump on my 2001 Jimmy and now there is a squeal (sounds almost like metal to metal) that I cannot figure out where it's coming from. I have replace the alternator, idle pulley, and the tensioner pulley with no change. The squeal starts up after the engine has ran for a little while. Also, I noticed that the temp gauge bounces a bit when driving. It will start climbing then drop back down then back up to where it was. The heat works great though. I have also put on different belts to no avail. Where do I look now? Could the new pump be the issue?

silverlite Enthusiast

silverlite

Posted
Posted

Blazerforum.com

 

Since the Jimmy & Blazers are basically the same vehicle & the engines are identical you will find your answer there. They're very helpful. Best place for answers.

silverlite Enthusiast

silverlite

Posted
Posted

Additional note: when replacing a water pump it's also highly recommended to replace the fan clutch at the same time. If you didn't change out the serpentine belt with the new pulley then changing that would also be helpful since it was running on the old pulley.

 

Dayco Part #5060950 serpentine belt grips well. This part is for the 4.3L Vortec engine. Much quieter & less stretching. Best price for it is on EBay for about $24 including shipping. It's almost $40 to buy it at Advance Auto Parts for the exact same part.

 

Water pumps, like any other part, can still be defective despite being new. I went with a new one that was OEM when I changed out it on my 2002 Chevy Blazer. Bought it from a seller on EBay. It worked perfectly after installing it. Still no problems for almost a year now.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,915
    Total Members
    8,960
    Most Online
    ChristopherDobson
    Newest Member
    ChristopherDobson
    Joined

  • Who's Online   5 Members, 0 Anonymous, 1,296 Guests (See full list)

  • Latest Articles

  • Posts

    • ChristopherDobson
      Vehicle Payments

      By ChristopherDobson · Posted

      Monthly payment is only part of the equation. With today's prices and interest rates, I'd look at the total monthly cost: payment, insurance, registration, fuel, maintenance, and expected repairs. A vehicle that fits comfortably into your budget is usually the better choice than stretching for a higher trim. I've also kept my vehicles longer over the past few years. New cars have gotten expensive enough that driving one for 10+ years, while staying on top of maintenance, often ends up being the most cost-effective approach.
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      10 Ford and Chevy engines proven to reach 300,000 miles   You may note a common 3K OCI on this list of gas motors. I skipped over the diesels. Dh'O. 
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      Thanks newdude!  By the time manual selection is needed, I'm probably too much of a control-freak to depend on the transmission sensing braking to activate automatic downshifting.  I would be anticipating the situation and already be manually downshifting.   This truck replaced a 2004.5 LLY diesel with the Allison 5-speed.  Putting it in T/H made noticeable differences (when the torque converter locked, upshift points, downshift behavior).  On this 2024 gasser with the 10L1000 I haven't been able to detect much, if any, difference.  Ok, I can never tell now when the torque converter locks up.  But I also don't notice differences in shifting.  For downhills, I've probably already manually downshifted by then anyway.  Since it's also more awkward (than the 2004.5) to engage/disengage I don't even bother.  Or maybe it doesn't really matter with just a 3k lb. camper in the bed?   Thanks also for the list of reasons the charging system might select various voltages.  However, what I am seeing doesn't fall into any of those categories.  It very definitely, and very consistently, rises after coasting/braking.  Maybe not immediately, but not very long after coasting/braking.  Very consistently drops voltage when no longer coasting/braking.  It might also be interacting with the camper battery charging (I might disconnect the camper and see if it changes the charging behavior).  I also need to recheck turning on headlights for when I want to force it to charge the camper.   Another JR, in June I converted the camper to LiFePO4.  Since it's not a good idea to try to charge lithiums directly using truck, I installed a Victron Orion XS DC-DC charger (which BTW is AMAZING!!).  Being cheap, I only had to buy that one item (besides the battery, of course) to do the conversion.  The camper OEM 120v battery charger (only 19 years old and works perfectly) and the truck feed the input to the DC-DC charger (not at the same time).  But I didn't want the camper charger feeding back to the truck so I kept the old separator.  I considered replacing the separator with a 30amp diode but that means more work and might add another 1/2 volt drop.  One thing that surprised me was the voltage drop over the long 10awg wire run, so I can only charge smoothly at 8 amps (because the DC-DC charger is completely configurable).  Another reason I don't want an added voltage drop with the diode.  I might also be a little lazy but all this work is being done under the sink with a small cabinet opening.    
    • davester
      cam upgrade in CA

      By davester · Posted

      apparently CA smog is (or at least was)  checking that the vehicle is using the oem and/or a ca smog approved tune, so I expect you'll fail inspection doing it.
    • davester
      Possible lifter tick after DOD delete

      By davester · Posted

      yes, leaking exhaust will mess up o2 sensor readings, which in turn messes up fuel trims.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...