Jump to content

2011 GMC Sierra 1500 electrical problem

Craigy
 Share

Recommended Posts

Craigy New Member

Craigy

Posted
Posted

I have a 2011 GMC Sierra 1500. As others have said on this forum, the truck started having weird electrical problems: the door locks would cycle locked and unlocked rapidly, different warning lights in the dash would come on and the tach and speedo would fall to zero then come back to where they had been. I cleaned the contact points of the negative battery cable (alt and frame) and the problem went away for a few months. Recently, the problem returned but with a new twist: when I shut off the engine, there would be no power until I jiggled the small ground wire on the negative battery cable--then it would start and run fine. I've read the fixes others have come up with on this forum and am wondering how long the fix lasted (weeks, months, years?); no one seems to bother to follow up with that information. I would appreciate it if someone would address this. Thanks.

dsr611 Senior Enthusiast

dsr611

Posted
Posted

Have you had the battery checked? If it's the original battery, it is getting close, and probably past, its lifespan. The battery in my '10 lasted about 5 years. Low batteries can cause all kind of electrical gremlins in these trucks.

  • Like 1
HK GUY Enthusiast

HK GUY

Posted
Posted

I have a 2011 Silverado and had the same problems. I had it towed to the dealer who had it for 3-4 days and said it was a loose ground at the battery. Drove it for a few months and it happened again. I did some additional research and came to the conclusion it was the ground cable itself. I ordered a new one April 11th off Amazon, put it on, and haven't had a problem since then.

 

Sent from my SM-N920V using Tapatalk

  • Like 2
  • 5 years later...
Teddyshrew New Member

Teddyshrew

Posted
Posted (edited)

My 2011 Sierra 1500 similar problems. I have a new battery. My door clicker stopped working had got it to work for short time then quit working all together. My battery gauge on dash reads 15 V most all the time. It will drain the battery it it sets for 3-4 days. The park lights sometimes come on in middle of the night or will stay on. Head lights ( switch on auto setting ) will flash. I gust purchase this unit a few months ago. If setting at store with it off and in a few minutes it dash comes on and says low battery voltage. Dealership can't help they say voltage is normal and can't find anything wrong with loss of batty voltage???? . My email is [email protected]

Any advice as to what I can do myself repair shops here are no help 

Edited by Teddyshrew
asilverblazer Senior Enthusiast

asilverblazer

Posted
Posted
On 12/23/2022 at 12:06 PM, Teddyshrew said:

My 2011 Sierra 1500 similar problems. I have a new battery. My door clicker stopped working had got it to work for short time then quit working all together. My battery gauge on dash reads 15 V most all the time. It will drain the battery it it sets for 3-4 days. The park lights sometimes come on in middle of the night or will stay on. Head lights ( switch on auto setting ) will flash. I gust purchase this unit a few months ago. If setting at store with it off and in a few minutes it dash comes on and says low battery voltage. Dealership can't help they say voltage is normal and can't find anything wrong with loss of batty voltage???? . My email is [email protected]

Any advice as to what I can do myself repair shops here are no help 

Door clicker sounds like a separate problem, maybe the coin battery in the fob or the contacts are dirty underneath.

 

Don't think of it as a "battery" gauge, it's a gauge of the voltage available in the truck, Anything over 12 volts is from the alternator and is to charge the battery.

 

The question you need to be figuring out is why are the lights coming on in the first place? If they are on long enough - they'll run the battery down even if its new.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,903
    Total Members
    8,960
    Most Online
    RyGuy43
    Newest Member
    RyGuy43
    Joined

  • Who's Online   5 Members, 0 Anonymous, 580 Guests (See full list)

  • Latest Articles

  • Posts

    • davester
      My First Project and GMC has me stumped

      By davester · Posted

      can you tell if the reader is actually trying to get codes, and the pcm is reporting none, or is your reader just silently failing because it's not communicating with the pcm?
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Any joy with this truck seems to be short-lived.   The CEL for P0172 ("bank 1" too rich) is now "intermittent".   I'm not sure where to check, or re-check, and my energy to keep chasing problems with junk is wearing thin. The P0172 seems to set as I'm coming to a stop, completely off the throttle, when fully warm. At least, that's what it's done the 3? times it's set.   Everything appears normal on the scanner EXCEPT long term fuel trim. There's only one bank on this vehicle because it's an OBD 1.5 with only one upstream O2 sensor. At idle, it's around -16.4% and will dip to -18% occasionally at idle or off-throttle. LTFT approaches 0 when throttle is held at 2500rpm. Short term appears normal, much closer to zero all the time. The LTFT tells me the engine is running rich at idle but compensating at higher load. But, why?   The EVAP purge valve doesn't appear to be leaking/sucking fuel vapor continuously. Is it sticking just as I come to a stop and the engine is choking on fuel vapor and sets the P0172? But that doesn't explain the persistently negative LTFT. Disconnecting the purge valve doesn't seem to make any difference.   I suppose that leaves another dang issue with the fuel injector. A leaking fuel pressure regulator, a new leak in the spider, or a leaking fuel injector/poppet valve I didn't see, or a small crack in one of the spider legs.   The vacuum line leading to the fuel pressure regulator doesn't have raw fuel in it. It doesn't even smell like fuel when it's pulled off, not until you suck air through it, then you can tell it leads to a fuel component. I'd consider that normal? Nothing is signaling this is a FPR issue from the outside, at least.   The oil smells like fuel but it's not building volume. I've noticed most oil in most engines smells like fuel to some degree so it's hard to say if the smell is an issue or not. Or if the engine just still smells like fuel because the crankcase was full of it a few hundred miles ago. But it's been changed twice since that original issue of the leaking fuel line dumping fuel into the intake.   Patience is running very thin. Every win seems to be accompanied by two steps backwards, or another issue that leads to removing at least the top half of the intake manifold. Enough! LOL
    • Chuck FB
      Tire pressure for 37s

      By Chuck FB · Posted

      First off you mentioned "Toyo Says" and then gave the pressures 45/50, was this some person at the tire shop that pulled those numbers out of his head ?   Now of course I can't know your exact axle weights front and rear, however I have much the same pickup as yourself other than not knowing your starting weight as per the pounds the truck rolled out of the factory at due to the options yours did or didn't come with or what you have added beyond the extra tire weight. The correct way to know 100% where a person is at is by weighing each axle with the typical weight the vehicle is driven with and that means taking into account passengers and making sure you figure in a full tank of fuel and a little grace for whatever you may put in the bed "groceries" !    I am looking at and not that it really matters as all the tire companies use the same charts anyway, but I am looking at the comprehensive Toyo tire chart in the section that your tire falls under and I know it sounds confusing but your tire is not an LT metric tire like your factory tire but instead because its a standard inch measured tire its under a different category called an LT floatation series tire. That makes a difference as LT metric tires they don't want to see run below 35 psi at highway speed where as with the LT floatation series it can be run down to 25 psi on the highway as long as the weight on the said size of tire is agreeable with or less than that minimum 25 psi. It blows many people away that how is this physically possible, an empty truck for one thing and larger tires with the same size wheel diameter have a lot more air volume so they can carry the same weight as the smaller tire with less air pressure.    So my truck, I have the stock 275/65R20 wheels and tires and I have a bit of weight in the box with a bak flip cover and a rubber bed mat and some tools and spare gas. The front of my gas truck weighs a bit more than some trucks of the similar spec due to double batteries and alternators. However with full fuel and just me in the truck I am weighted such that I can run 40 front and 35 rear and so that is what I have done since day one.    If I base your truck at or slightly below the weight of my truck, in theory with your tires going by the tire chart you might be right around a minimum of 30 pounds front and 25 pounds rear. Of course that would hit pretty much minimum cold inflation pressure one could run with that tire size and a near empty truck. If you have access to an accurate weigh scale to do individual front and rear axle weights I would suggest you do that and make sure your topped up with fuel and whatever else in the truck before you weigh it and then you will have a great starting point to work off of and figure out what your bare minimum pressures are you can safely run. If you do much in the way of hot weather high speed driving, bumping up a bit for a safety margin is never a bad idea but just depends on what type of driving you do. I will include the Toyo chart and the floatation series sizes start on page 31. Without a doubt at these pressures I am speculating at minimum wise for your truck, it would most certainly ride very different then it did when you were using 55 lb front and rear.     https://www.toyotires.com/media/pxcjubjs/application_of_load_inflation_tables_20200723.pdf
    • Snowcamo
      Possible lifter tick after DOD delete

      By Snowcamo · Posted

      Take an automotive stethoscope to the vacuum pump. Iirc those tick as well. 
    • rdonarski
      Towing In Loose Gravel

      By rdonarski · Posted

      This landing is worse than most. Patchy blacktop with washouts, soft gravel/sand at bottom that washes out with every heavy rain. I tell everyone to put it in 4WD. A lot of them think they can pull out their trailer in 2WD. They end up digging a hole and then putting it in 4WD.  The lake is a pristine lake and has a lot of money on it. There are several wake boats and lot of large tritoons. The people with the money don't want it improved because they don't want more traffic.    Boat Landing 1.jfif Boat Landing 2.jfif Boat Landing 3.jfif

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...