Jump to content

Wireless charge upgrade


Recommended Posts

Posted

2015 suburban. The truck came from factory with it and it sucked. Heres my upgrade.

 

Took apart the lid. Underside cover is held on with retainer clips. Take your time, they are on there good.

Once off you will see torx screws, t15 is the size.

I had to cut the opening bigger for the charging pad and raise it up so it sits directly underneath the rubber mat.

I hard wired it to the 12v cig lighter in the back of the consol. To remove the cover its 4 torx screws t20. 2 at the top and 2 at the bottom behind the rubber inside the cubby. Lift up and towards the rear of the truck. There are 2 clips at the top holding it inplace.

 

To assemble just reverse everything. Only issue i have is the ru ber mat above the charginf pad is too thick. Phone charges without case but not with case.

 

The clip is the factory plug to charge pad. Dont use it. With this mod you do lose the charge icon on infotainment center.46faab761430a9725fa17e31670bc744.jpgc45f8d94dfbece414c99d86aa68508a8.jpgdc8498d84f826f2783431ad9eebf6103.jpg0b9c95013e2d603bc0990b6c80a23b5c.jpg

 

Sent from my SM-G935P using Tapatalk

Posted

Thanks for the pictures. Is the new charging unit a lot faster than the factory module?

 

 

2015 suburban. The truck came from factory with it and it sucked. Heres my upgrade.

Took apart the lid. Underside cover is held on with retainer clips. Take your time, they are on there good.
Once off you will see torx screws, t15 is the size.
I had to cut the opening bigger for the charging pad and raise it up so it sits directly underneath the rubber mat.
I hard wired it to the 12v cig lighter in the back of the consol. To remove the cover its 4 torx screws t20. 2 at the top and 2 at the bottom behind the rubber inside the cubby. Lift up and towards the rear of the truck. There are 2 clips at the top holding it inplace.

To assemble just reverse everything. Only issue i have is the ru ber mat above the charginf pad is too thick. Phone charges without case but not with case.

The clip is the factory plug to charge pad. Dont use it. With this mod you do lose the charge icon on infotainment center.46faab761430a9725fa17e31670bc744.jpgc45f8d94dfbece414c99d86aa68508a8.jpgdc8498d84f826f2783431ad9eebf6103.jpg0b9c95013e2d603bc0990b6c80a23b5c.jpg

Sent from my SM-G935P using Tapatalk

Posted

Thanks for the pictures. Is the new charging unit a lot faster than the factory module?

 

 

A little faster, gm said my phone was not compatible. It was very touchy to gwt to work. Now i can place anywhere on there and it charges.

 

Sent from my SM-G935P using Tapatalk

Posted

do you have a pic of it all out Bach together? thanks

Which part the top of the console lid. Looks factory, you couldnt tell i changed it

 

Sent from my SM-G935P using Tapatalk

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.6k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    343,007
    Total Members
    8,960
    Most Online
    Brendan C
    Newest Member
    Brendan C
    Joined
  • Who's Online   0 Members, 0 Anonymous, 972 Guests (See full list)

    • There are no registered users currently online
  • Latest Articles

  • Posts

    • You're better read than that Atlas. 😏   British science fiction writer Arthur C. Clarke formulated three adages that are known as Clarke's three laws, of which the third law – that "any sufficiently advanced technology is indistinguishable from magic" – is the best known and most widely cited.   Stribeck and the pivotable Hersey Number isn't voodoo nor snake oil. That part is physics. It's what marketing and bean counters do with it that is snake oil and voodoo.    Stribeck is the relationship between Hersey and the Coefficient of Friction. Within the Hersey Equation if viscosity and viscosity is 'Dependent' on.......heat.......and.......viscosity index or the temperature to viscosity slope.    Specifically Hersey is the viscosity AT THE TEMPERATURE IN THAT LOCATION FOR THAT SLOPE.   Hydrodynamic lubrication exist when the film thickness in the location is 3X the Ra roughness of the surface. This is irrespective of the hardness of the substrate. To obtain that thickness X viscosity is required for Y velocity at Z load. That's a lot of moving parts. It is also impossible to maintain in an ICE but nearly possible with a turbine under constant load.    What does that mean? Error heavy and operate light. Wear is inevitable but the rate of wear and the milage obtainable are a function of prevailing conditions and HABITS. The only penalty is viscous drag and at fractions so low as to be well worth the effort. Double the life, half the manufacturing carbon foot print. Greed is the only impediment.    The materials generated by SwRI are the RESULT not an estimation or a hypothesis.    Don't delude yourself sir, EV's have as many pitfalls as ICE's. We just don't know what they are yet and it will take longer to sort as MARKETING and GREEDY CEO's have had more time to polish the turd they are selling. 
    • You can always count on greed to prey on ignorance and stupidity.    Friend bought a 2019 Ford Flex and asked me about using Valvoline R&P 5W30 in it. Told him give the miles on it and the fact it wasn't yet using oil that it was a good plan. He uses a Valvoline quick change shop for his oil service.   First they tell him that isn't the oil the OEM recommends. He told them he didn't care what the OEM thought. Then they floated the, "But it will void your warranty"    His reply was it's a 2019, there is no warranty and informed them their knowledge of the law was lacking.    Then they tell him 'But it will ruin your motor"!.    Mine to ruin he says. Finally they give in and charge him 150% the semi-syn price    Point it the brainwash is so embedded that even the service industry is drunk on their swill. The public is right behind them. Echoing the same lies on every forum and media platform. If the end goal is indeed EV then I'd say that ship is about built. 
    • Diesel hit $6.00 here today at the truck stop.   Payed $2.79 for E85 today too.
    • Thanks for posting, I'm sure it will help someone
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...