Jump to content

Check Engine Codes

Ajnthony
 Share

Recommended Posts

Ajnthony Enthusiast

Ajnthony

Posted
Posted

So I installed a bull bar with a led light bar last weekend and all seemed to go well until my check engine light came on the next day.  The codes that come back are U1345 and U01B0. I tried clearing them but they came back.  Any ideas on what these two codes are and how to fix the problem? Any help is much appreciated. Thanks. 

 

 

 

 

u

davester Senior Enthusiast

davester

Posted
Posted

I would look at the wiring you did, and the wiring around it, that you may have moved, maybe you hooked up to the wrong wires, or worked some connector loose, or something along those lines.

Rocz3cqg Enthusiast

Rocz3cqg

Posted
Posted (edited)

U1345 could be Fuel and Air Metering, Fuel Rail Pressure Sensor Circuit Malfunction, Engine Shutoff Solenoid Malfunction or Shift / Timing Solenoid Malfunction / 3-2 Shift Solenoid Circuit Electrical. U01B0  might be Lost Communication  with Battery Monitor Module. I am with DaveSter, check the wiring and for any plugs that are loose.

Edited by Rocz3cqg
Ajnthony Enthusiast

Ajnthony

Posted
  • Author
Posted

Thanks for the suggestions. I should have mentioned this is a 2019 Silverado 1500 trail boss. It may have something do with the fact I don’t know how to reinstall this wiring harnesses see photos. 

52695D3F-6CA1-464B-91C4-B3C83CE25CAC.jpeg

Ajnthony Enthusiast

Ajnthony

Posted
  • Author
Posted
1 hour ago, Rocz3cqg said:

So no plug found to connect or you forgot to connect?

I need a photo of under the glove box of a 2019 Silverado to remember how to but this Electronic piece back. It’s plugged in but just dangling at the moment until I figure how to but it back into its lance correctly. Unlikely this is the cause of the check engine light though. But I am backwards mapping to try to locate the problem. This is next on the list. 

  • 5 months later...
grrr027 Enthusiast

grrr027

Posted
Posted

@Ajnthony any update on these codes? I have a Sierra with 1300 miles and got the same two codes after installing a leveling kit.

Ajnthony Enthusiast

Ajnthony

Posted
  • Author
Posted
5 minutes ago, grrr027 said:

@Ajnthony any update on these codes? I have a Sierra with 1300 miles and got the same two codes after installing a leveling kit.

Yes. I finally took the truck into the shop for the recalls. Asked them to check on the check engine light and codes. They cleared it and said it was a lost signal with the battery. Nothing major but they had to reprogram and reset I guess.  All good now and they didn't charge me anything. Hope this helps. 

grrr027 Enthusiast

grrr027

Posted
Posted
4 minutes ago, Ajnthony said:

Yes. I finally took the truck into the shop for the recalls. Asked them to check on the check engine light and codes. They cleared it and said it was a lost signal with the battery. Nothing major but they had to reprogram and reset I guess.  All good now and they didn't charge me anything. Hope this helps. 

Yes, that helps a ton, thank you! I’ll call the dealer today.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.3k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,716
    Total Members
    8,960
    Most Online
    BDS my HD
    Newest Member
    BDS my HD
    Joined

  • Who's Online   0 Members, 0 Anonymous, 460 Guests (See full list)

    • There are no registered users currently online

  • Latest Articles

  • Posts

    • BDS my HD
      Brand new to this forum. Questions about re-gearing my 26’ HD

      By BDS my HD · Posted

      Hello hello looking forward to expanding my knowledge of the 2026 2500 HD that I just bought.   Truck has 3500 miles on it four-wheel-drive crew cab and I’m about to put a 6 1/2 inch BDS lift on it 18 x 10 -25 offset with 37’s   Already have the wheels and tires just waiting on the lift install in about three weeks   Question what surprises am I not gonna be happy with?  I’m not new to lifted trucks so I know that acceleration towing gas mileage all that is affected..   Question is those of you that have this truck this powertrain with a 10 speed Allison and have done the mods that I’m doing,,, how bad is it? Is that Allison constantly gonna be hunting for the right gear to go into? And what about towing, acceleration, fuel consumption as mentioned?    Lastly how come I can’t find any ring pinion gear set up for these axles and when could I expect to see them?   I apologize if there’s any typos I’m doing speech to text on my iPhone.    
    • linc45bn
      2013 2500HD 6.0L intermittent no crank no start

      By linc45bn · Posted

      I've got a 2013 2500 6.0L Flexfuel. Drove the truck earlier today with no issues. Went to run an errand tonight and noticed key fob wouldn't work. Figured battery was dead, so replaced fob batter. Still wasn't working. Grabbed my other set of keys with the other fob and that one wasn't working either. So I manually unlock truck and insert key. Interior lights come on, dashboard lights up, turn key and truck starts. Turn truck off, like a moron, and try starting again. This time no crank, no click, no nothing. Lights still come on and dash lights up, but now I'm getting a service 4wheel drive, service tire monitor, etc. Check voltage on battery and Im showing 12.2v. Throw my battery charger on it and give it 15 mins and try starting again. But still no crank no start. Decide maybe its a bad battery, run to autozone grab a new one and put it in. Same issue. Disconnect battery and let it sit for 15 mins. Try again and still nothing. I had managed to roll the windows down earlier as its a humid night, but now I can't get them to roll up. Power locks are also not working now. Then randomly I try the key again, and it fires right up. Immediately I roll up the windows as we have nothing but rain forecast this week. I shut it back off wait 30 seconds and start up again. Worked a 2nd time. So turn it off, start putting things back together. Try one more time, and back to no crank no start. And now the car alarm starts going off. Had to disconnect battery and leave it that way for the night as I don't think my neighbors would appreciate my alarm going off again tonight. Any thoughts or help would be appreciated. 
    • Grumpy Bear
      first oil change - 2026 2500HD gas

      By Grumpy Bear · Posted

      No one will care for you like you care for you. Do what you can for as long as you can. IMHO of course. 
    • Grumpy Bear
      Oil Consumption

      By Grumpy Bear · Posted

      How about them NICKS!!! 
    • Peoplemvr
      GMC 1500 Illuminated Front Grill Emblem REPLACEMENT.

      By Peoplemvr · Posted

      Hi there.  Long time lurker, first post.    i have read the previous posts regarding the water ingress problem with this emblem.  I bought my 1500 SLT the  summer of 2025 new and after reading the MANY problems with these emblems failing I decided to install one anyways.  As per a YouTube video, I sealed ( or tried to) this sign with silicone sealant around the outer perimeter joint and the holes that were already somewhat sealed on the rear plate of the emblem.  And installed the connector assembly using dielectric grease on the connectors. The installation looked great and worked well for about 4 months……then FAILURE.  Grrrrrr…… I live in the great white north and wash my truck weekly in an automatic car wash  to keep the salt off.  Let me tell you that removing the old, failed emblem is a whole different animal than removing the OEM individual letters without removing the grill assembly. Mainly because the illuminated logo is built differently than the original letters which  you can remove the red surface lettering with a knife or some kind of blade which gives access to the tabs which hold the logo onto the grill. So I had to essentially destroyed the old emblem to remove it. Doing so killed my chance of doing somekind of autopsy on the failed , old logo.  But there was plenty of water inside when I ripped it apart.  Prior to installing the new assembly I tried it with the old harness and it works fine.   Does anyone have any insight as to where the water is getting into this emblem? I intend to seal the new logo with slow curing epoxy this time around using a syringe.  I think this newer emblem may be an updated unit which I hope GM got the vendor to fix. It has an October 2025 date on it.    If this one  fails,  I am just going to revert back to the non-illuminated letters….AFTER PULLING THE GRILL.    Any thoughts on sealing with epoxy would be appreciated. Thx!   Doug  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...