Jump to content

Lift/Tire Ratio

Mike Reitzloff
 Share

Recommended Posts

Mike Reitzloff Enthusiast

Mike Reitzloff

Posted
Posted

Ok, I know many of these conversations have taken place already, but I'm having a hard time finding specific info that I'm looking for and am hoping someone out there can help out.  I have a 2017 Sierra Denali (1500).  I'm trying to decide between a 2.5" RC leveling kit, which replaces factory 1" block in the rear with a 2" so would raise back by 1" it seems, or  Motofab 3" front/2" rear level.  With the RC 2.5", a reviewer on their site says he went with 285/60r20 Duratracs with no rubbing issues.  The Motofab 3" has a reviewer that says he's running 285/65r20 but doesn't say whether or not there's any rubbing or trimming needed.  I don't want to do any offsets or trimming.  I'd of course like to have 0 rubbing, and I want to stick with factory 20" wheels.  I'd love to go with the 285/65's if possible, but if those wouldn't fit with the 3" kit, I'd rather go with the 2.5" because I like the look of filling the fender wells as much as possible, so I don't want to lift higher if I can't run larger tires with it.  Anyone running 285/65's with a 3" kit??  Thanks for any help anyone can offer!

  • 2 weeks later...
18redhot Enthusiast

18redhot

Posted
Posted

You’ll be safe running the 285/65s with the 3” for sure, at most maybe zip tie the carpet back, no metal trimming. You will more than likely rub the sway bar and uca with both kits at full crank 

Mike Reitzloff Enthusiast

Mike Reitzloff

Posted
  • Author
Posted

That's good to hear, thanks for the info!  I really liked the look of the truck with the 3" and the 285/65s a lot.  As far as rubbing the sway bar and uca, I have to ask because I'm new to the truck world (this is my first truck), is that not that big of a deal?  It sounds like it'd be bad, lol!

18redhot Enthusiast

18redhot

Posted
Posted
51 minutes ago, Mike Reitzloff said:

Yeah buddy tbh you could run a 295/65 all terrain and get by, I’m putting 35 12.50 venom power terrain hunter xts on mine when I get some time off work, I’d recommend the motofab 3/1 with ucas I already have the kit and the quality seems unmatched for the money, around 400 for everything, use promo code pc10 it’ll get you around 40$ Off the kit 

9C9F834A-DF6A-4539-B1C3-B2A01DC29539.jpeg

DCB9A228-EB98-4687-8751-ABCD53D97497.jpeg

DA006DD9-1464-4F65-91AA-4C1B2F24B00D.jpeg

18redhot Enthusiast

18redhot

Posted
Posted

Also, rubbing the uca isn’t too big of a deal, just don’t go full crank lol. In all reality it pretty much just rubs the finish off and there will be a shiny spot, ran a nnbs Silverado rubbing the sway bar for 120k no issues 

Mike Reitzloff Enthusiast

Mike Reitzloff

Posted
  • Author
Posted

Ok, cool.  Good to know!  Thanks for the input!  I think I will go with the Motofab 3" kit.  You'll have to post some pics of your truck when you get that kit installed, it sounds like it's going to look great!

amxguy1970 Senior Enthusiast

amxguy1970

Posted
Posted

Nothing is specific, all trucks have a tolerance and a slight variance. What may work for some person might not work for another especially when trying to push the boundary. Tire brands and styles play a hand in it as the same size tire between two manufacturers aren't the same exact size. That is why you search and do your due diligence on all the other thousands of threads and see what most people have works. I personally wouldn't go with what one or two people said in a repetitive thread as the people who may have your specific set up including tire type and brand may have seen something different but they aren't going to go in to 5 threads a day answering the same question when they already have in another thread. 

 

As far as the kit goes, your truck is going to hate you. That is why I won't buy a used truck as you never know what the previous owner did and took off. The 3 inch level puts you about maxed out on droop and all the other angles are going to be horrible for long term wear. Even adding UCA's the lower control arms, tie rods and CV's are going to be at pretty extreme angles. If you aren't off roading they may last longer but that is still extreme. Many people for some reason or another say 2.5" is safe (not sure how they pulled that number out of their azz) but that is not the case, anything higher than stock just reduces the life of the components. The further you go from stock the more time it takes out of other parts, just remember that. The larger and heavier you go with tires will also impact your wheel bearings as well as negative offset wheels (very popular in Texas). Just some info for you for a first time truck owner.

 

My set up I went 1 inch larger with tires and stayed P-rated to gain minimal weight and did a 1.5"level in front and 1" rear to keep rake when towing and hauling, I ended up changing the level out to Bilstein leveling shocks when my stockers were worn and set them at 1.25". If you do plan to tow or haul keep some rake in your truck, it will drive and handle better level as too much sagging takes weight off the front tires. Also remember to adjust your headlights down so you don't blind on coming traffic once you have it installed, a large level will be like running around with your brights on to everyone with an HID or LED set up. 

 

One more thing, I think your truck has magnetic ride control so I think that may limit level choices? I am not sure as I didn't go that route so I haven't checked in to it, just what I have seen. Maybe that is an option and wasn't standard? 

 

Tyler

18redhot Enthusiast

18redhot

Posted
Posted
5 hours ago, Mike Reitzloff said:

Ok, cool.  Good to know!  Thanks for the input!  I think I will go with the Motofab 3" kit.  You'll have to post some pics of your truck when you get that kit installed, it sounds like it's going to look great!

Check out lmfscrew on YouTube, very helpful 

Mike Reitzloff Enthusiast

Mike Reitzloff

Posted
  • Author
Posted

I checked out a few of that guy's vids, it does seem like he has some good info for sure.  

 

*Tyler, you have a good point there.  I have done quite a bit of research though, and if parts wear prematurely, I will just have to replace as needed.  I want my truck to look tougher than the stock look.  I don't think they're tall enough off the assembly line.  The Denali's do all have magneride for the '14-'18s.  These kits I'm looking at come with the magneride sensor relocation brackets to maintain factory ride quality.  I agree about leaving some of the take in there for towing though.  That's why I am leaning towards a 3" front/2" rear kit.  That only reduces the take by an inch.  I believe they are at least 2" take stock, and I do plan on pulling a camper with it, but I won't go more than 6K lbs @ under 600 lb tongue weight, so I'm hoping that wouldn't cause me to squat.  ???  It seems there are a LOT of guys out there lifting these things though, so I would think more of them would be mentioning problems if they were common with these kits.  Idk, maybe I'm wrong there.  

18redhot Enthusiast

18redhot

Posted
Posted
50 minutes ago, Mike Reitzloff said:

I checked out a few of that guy's vids, it does seem like he has some good info for sure.  

 

*Tyler, you have a good point there.  I have done quite a bit of research though, and if parts wear prematurely, I will just have to replace as needed.  I want my truck to look tougher than the stock look.  I don't think they're tall enough off the assembly line.  The Denali's do all have magneride for the '14-'18s.  These kits I'm looking at come with the magneride sensor relocation brackets to maintain factory ride quality.  I agree about leaving some of the take in there for towing though.  That's why I am leaning towards a 3" front/2" rear kit.  That only reduces the take by an inch.  I believe they are at least 2" take stock, and I do plan on pulling a camper with it, but I won't go more than 6K lbs @ under 600 lb tongue weight, so I'm hoping that wouldn't cause me to squat.  ???  It seems there are a LOT of guys out there lifting these things though, so I would think more of them would be mentioning problems if they were common with these kits.  Idk, maybe I'm wrong there.  

1-2” of rake will be fine for towing your camper assuming you have a load leveling hitch, just make sure to check what control arms you have, the stamped steel are dangerous with the larger leveling kits due to lack of ball joint support, and some people suggest new ucas for aluminum also 

Mike Reitzloff Enthusiast

Mike Reitzloff

Posted
  • Author
Posted

I'm trying to find out what UCA's I have still.  I feel like this stuff is way more complicated than it needs to be.  I just wan to make my truck taller.  I feel like the guys that make the lifts should be able to tell me exactly what I need to accomplish that without screwing crap up.  The Motofab UCA's say they don't fit Denali's.  So I will have to do some more digging around to find out I guess.  Thanks for the info though!  This is definitely helping!

18redhot Enthusiast

18redhot

Posted
Posted
On 10/26/2020 at 10:29 AM, Mike Reitzloff said:

I'm trying to find out what UCA's I have still.  I feel like this stuff is way more complicated than it needs to be.  I just wan to make my truck taller.  I feel like the guys that make the lifts should be able to tell me exactly what I need to accomplish that without screwing crap up.  The Motofab UCA's say they don't fit Denali's.  So I will have to do some more digging around to find out I guess.  Thanks for the info though!  This is definitely helping!

https://www.readylift.com/blog/2017/07/11/upper-control-arms/

 

this should help ya out bud, best to do all the research you can so you don’t get your truck torn apart and run into something that will have you scratching your head. Pm me if you want I’d be glad to help walk you through it 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • txab
      Gas Prices

      By txab · Posted

      The whole story is false. The screw is there as a temporary fix to allow the pump to even turn on. When the nozzle is returned the pump shuts off.. At this point people are just being punked   https://youtu.be/1DtlaEuHXAA?si=06mrRmw9HLUwdeRk   https://www.facebook.com/share/v/1CyRZdsaSc/ https://www.facebook.com/share/r/1DxV1Hyrqi/       SNOPES: https://www.facebook.com/share/p/19HPYUnRik/
    • newdude
      2027 GMC Sierra: Official Discussion

      By newdude · Posted

      Follows the motif on the Sierra EV.  Satin finsh to the lower bumper area, painted above:   Elevation       Denali      
    • taze
      I love my truck but

      By taze · Posted

      Not exactly what I was hoping for, but I do like it. I wonder if they'll bring back Smokey Quartz Metallic? 🤔 https://gmauthority.com/blog/2026/06/here-is-the-all-new-2027-gmc-sierra-1500/
    • tjonesdfw
      2027 GMC Sierra: Official Discussion

      By tjonesdfw · Posted

      Whoever greenlighted the work truck matte black front bumpers on every trim but the AT4X should be fired!  I was hoping that was an AI mistake, but just realized they were on every model of the 2027 Silverado too.     Some parts of the interior do look premium, but the Denali Ultimate dashboard looks like an afterthought.  At least they appear to have lost the microfiber the high end Silverado models showed, but the '27 High Country dash looks better than the Denali.  
    • bluev8
      Intermittent no-code issues on 2022.5+ V8 trucks — what did the shop fail to capture?

      By bluev8 · Posted

      New member here. I am researching a read-first event-recorder concept for late-model GM V8 trucks. This is not a sales post. There is no product link, price, preorder, or mailing list. I am trying to determine whether the underlying problem is real before building anything.   Has your truck ever had a brief problem such as: - rough running or a momentary misfire - an oil-pressure warning or unusual pressure event - reduced power or a brief stall - a U-code or lost-communication problem - a symptom that disappeared before the dealer or independent shop could reproduce it   If so, I would appreciate the following details: - year, model, engine, and mileage - what happened and under what conditions - whether a DTC and useful freeze-frame data were stored - whether the shop was able to reproduce it - what the eventual confirmed repair was, if known - what additional information would have helped the diagnosis   The concept being evaluated is a removable leave-in recorder that continuously retains a rolling window from before and after an event. It would not tune, reflash, clear codes, or change the vehicle calibration.   I am also not claiming that it could predict lifter failure or see every internal ECM variable.   The real question is whether continuous event history would add enough useful evidence beyond freeze frame, GDS2, and existing scan tools — or whether it would simply be another unnecessary gadget.   For owners and technicians, which problem would make something like this genuinely useful: 1. intermittent misfire or AFM/DFM-related behavior 2. oil-pressure events 3. lost communication or electrical faults 4. none of the above Please be blunt. Negative feedback is just as useful as positive feedback.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...