Jump to content

Low speed vibration 5.3l /6.2 with 10 speed transmission

SSsierra
 Share

Recommended Posts

SSsierra Enthusiast

SSsierra

Posted
Posted

I have a 2020 sierra crew cab with 5.3, 10 spd trans and having low speed vibration 28-10 mph (deceleration or acceleration). I took vehicle to dealership on Monday. Two days later dealership called and stated all the test they performed (DFM, Trans mount ect..) was working as design and nothing could be found to cause issue. During this call I stated to service manager what was I suppose to do just live with this issue. I also stated that i was on GM truck forums and there where numerous identical issues, do I need to have a GM-Tech reach out to them? Service manager said let me talk to shop foreman/supervisor and see if there is anything he can do. Next day service manager was having another Pico scope test done to try and find issue. UPDATE; Shop foreman/supervisor called GM-Tech and they requested another Pico Scope be performed and to send them the results. Currently waiting on GM-Tech for guidance from Pico Scope results, should hear back from GM next week.  I requested a loaner vehicle and dealership stated i could come get my truck and that it was safe to drive until they get the guidance from GM next week. Will update  when GM gives guidance.

flyingfool Senior Enthusiast

flyingfool

Posted
Posted (edited)

what RPM and Gear are you in when it vibrates?

 

is there a simple way to disconnect the TCC clutch  by removing the connector to the TCC solenoid?

Edited by flyingfool
  • 4 years later...
davester Senior Enthusiast

davester

Posted
Posted

...4 year old thread, and the op hasn't logged onto the site in over 3.5 years.  You aren't likely to get a response from that user.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,833
    Total Members
    8,960
    Most Online
    White.6.2
    Newest Member
    White.6.2
    Joined

  • Who's Online   2 Members, 0 Anonymous, 610 Guests (See full list)

  • Latest Articles

  • Posts

    • Chuck FB
      Correct way to service 2024 l8t allison trans?

      By Chuck FB · Posted

      I have never seen GM instructions for the other trucks as per the HD with the 6 speed or the half tons but had got the impression that the HD trucks with the 6 speed were not having the same problem that the 10 speed and pan presented. Also video that I have seen of the HD 10 speed with the gas engine starting in 2024 model year showed that it was a real struggle to even make it work when pulling down hard on the exhaust after undoing the exhaust hanger bracket on the side of the transmission as after all there is little room for the pipe to even go down behind the Y joint as it soon would hit a frame cross member. Also that they had tried just like I did with the gasket off and no way was that pan coming out any way they tried to manipulate the pan. From that as well as the local transmission shop talking about the pain in the rear issue, I was not expecting my pan to come out because GM shows it was not even intended to come out without dealing with the exhaust piping.    It would be nice to claim, here's what you do and its easy to remove the pan guaranteed on any HD truck with the gas 10 speed but dollars to donuts the next guy trying what I did would not have the same luck as the exhaust was just manufactured slightly different and be pissed off at my claim that the pan comes out with no issue. Its more of a try and see if your particular truck might work like mine did .... or not !. 
    • carkhz316
      Correct way to service 2024 l8t allison trans?

      By carkhz316 · Posted

      Sorry I didn't see this until now, but it works on both the 6 speed and 10 speeds, as well as all the half tons too.
    • 1998sleaze
      Engine vibration after motor mount replacement.

      By 1998sleaze · Posted

      Hello, I have a 2018 GMC Sierra 1500 that I recently changed both motor mounts on due to the driver's side being blown out. After replacement I seem to have a steady vibration that I can feel in the pedals and the back of the seat. At this point I'm convinced that the aftermarket "Anchor" branded mounts I used are not performing as well as OE, the only real reason I ended up using the mounts in question was because my local dealers were out a few months to get a Driver's side mount. I've tried "Neutralizing" the mounts according to the motor mount TSB published for these truck to no avail. My trans mount is also in great shape and seems to be absorbing vibrations swimmingly. As far as I can tell there is no issues idling, my idle RPM is steady and I've recently put GM plugs and wires on, however, I have not cleaned the throttle body or intake valves. Any one else have a similar experience with aftermarket mounts? Patience certainly is a virtue that I wish I exercised here. Thank you!
    • CamGTP
      Winter Returned

      By CamGTP · Posted

      I still saw people out for runs, on their bikes/motorcylces, jeeps with the doors off driving around here the past 2 days. I guess we are just used to it here haha.   Tasted like a bonfire the last 2 days.
    • CamGTP
      6.2L (L9H) Owners - Get all your questions answered here

      By CamGTP · Posted

      The TCM has to be flashed before it can drive.   If you installed it the way it is, it has the OS (operating system/program) from the 2010 truck you got it from. That will not match with the VIN/OS pair that your 2013 truck has.   You can do the full install. Then tow it to a dealership and they can flash the trucks PCM/TCM with the latest program for your VIN.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...