Jump to content

Trailer light pre departure check

dquest
 Share

Recommended Posts

dquest Enthusiast

dquest

Posted
Posted

New 2022 just delivered and I was testing out the pre departure light test. It works properly ( lights, signals, brake illumination ) but the app says it is unable to complete. Anyone seen this before?

Tomato Enthusiast

Tomato

Posted
Posted
13 hours ago, dquest said:

New 2022 just delivered and I was testing out the pre departure light test. It works properly ( lights, signals, brake illumination ) but the app says it is unable to complete. Anyone seen this before?

Mine has done that but it continues after a few seconds. I think it is related to something I would do or a certain part of the test - can't remember which.

dquest Enthusiast

dquest

Posted
  • Author
Posted

I have retried it multiple times and still says it isn't working even though it is.  What does the app tell you if it does work. I'd assume it checks them off as they function but maybe that's too much to ask.

BrentH Enthusiast

BrentH

Posted
Posted

As I recall when last I towed, the app cycled through and then restarted itself and would cycle until I pushed the stop test button on the screen.  If you have your trailer plugged into the advanced trailering app, I believe I just get a no faults found response.  Typically I will get "cannot locate previous trailer brake settings" and I will acknowledge that and a few seconds later it will say that it located the settings and the gain is ok.  I have received error messages like left trailer brake light not working or there is an issue with the trailer connector.

 

I have not received an "unable to complete" alert other than when I was activating the tire pressure/temp sensors for the trailer.  That took a bit to get working and I had to do the install thing about 6 times - works now without issue. 

dquest Enthusiast

dquest

Posted
  • Author
Posted
3 hours ago, BrentH said:

As I recall when last I towed, the app cycled through and then restarted itself and would cycle until I pushed the stop test button on the screen.  If you have your trailer plugged into the advanced trailering app, I believe I just get a no faults found response.  Typically I will get "cannot locate previous trailer brake settings" and I will acknowledge that and a few seconds later it will say that it located the settings and the gain is ok.  I have received error messages like left trailer brake light not working or there is an issue with the trailer connector.

 

I have not received an "unable to complete" alert other than when I was activating the tire pressure/temp sensors for the trailer.  That took a bit to get working and I had to do the install thing about 6 times - works now without issue. 

I couldn't get advanced trailering.  The basic one just says try again or cancel but it performs the test.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,782
    Total Members
    8,960
    Most Online
    ShowMeShooter1332
    Newest Member
    ShowMeShooter1332
    Joined

  • Who's Online   1 Member, 0 Anonymous, 5,964 Guests (See full list)

  • Latest Articles

  • Posts

    • Jsdirt
      2027 GMC Sierra: Official Discussion

      By Jsdirt · Posted

      I was around and remember that era very well, so I'm calling b/s on that statement. If they were that bad no police department or taxi company would've bought a single one ... but they were used in both services (and fire) for DECADES. They were bulletproof and proven. Even the early 21st century ones weren't too bad! The early models were legendary.   Mine is proof, but people like atlas are blinded by agenda and refuse to believe facts right before their very eyes.   Even decades after they were built, a new generation started driving them, posting all their builds and shenanigans on Grandmarq.net and Crownvic.net. The failures would show up then, since they all were deep past 100k-150k miles by that point, and younger drivers tend to be a little aggressive, especially with vehicles than can lay a one-tire fire for as long as you hold your foot in it. They've more than proven themselves over the decades.   The only thing that'll really take them out is road salt. The bodies and sheet metal were garbage. A victim of the cheapout FoMoCo and GM have been partaking in before then, and since.   Today it's the stuff that counts - the undercarriage that rots away first!    GMs Caprice was no slouch either. Reliable as a stone ax - the opposite of what they build now.    
    • Jsdirt
      2027 GMC Sierra: Official Discussion

      By Jsdirt · Posted

      Let me know how your vehicles do in 10 years. You don't know ******, kid. 😂    There's a reason that Panther platform was used as police, fire, and taxi service for DECADES ... long before you were born, apparently.
    • davester
      Disconnecting Battery

      By davester · Posted

      If your connector also has a big lever to get the connector on and off, you don't want to force the lever either way, as it becomes a bigger problem if you bust the lever or the mechanism it works.
    • davester
      Disconnecting Battery

      By davester · Posted

      It's just useful to disconnect the battery to prevent odd shorting out when unplugging/plugging stuff together.  I also  touch the two cable ends together (after disonnecting) to drain the small amount of stored battery energy in various modules.   I believe the main system where you need to be more concerned with, so you need to do the above and then wait some time, iss when you are working on the air bag system, to prevent inadvertent firing of the air bags.   The in-cab switches are just that, plain switches, it's generally not a problem to swap them in/out.  For my '12, I'll get an error message on the dash if I power up the truck w them unplugged, but that's it (power up= turn the ignition on).   The ITBC located above the spare tire is a computer that manages the trailer brake system.  That is probably more important to have the battery disconnected.  It does have to be programmed to the truck, either before or after it's installed, for it to work.  For my '12, I had a very hard time reinstalling the main connector to it (IDK if yours is the same or not), it turned out the silicon seal was jamming up, preventing it from going on all the way.  I finally got it fully installed by lubing the seal with a bit of dielectric grease, then it slid on and latched in place easily.
    • BCGM
      Remote Start Noise 2024 2500 HD Gas

      By BCGM · Posted

      JR ! I just got the truck back from the Dealership today . The technician did a cold remote start on the truck this morning and it made the noise . It was determined that it was a starter issue and replaced it under warranty . Of course   it did not make the sound after a new starter was put in because the truck was not cold . We will we see what happens tomorrow morning when I start the truck cold  . Keep tuned !   Oh I found a video on YouTube of a cold start and it did the same thing your truck and mine do , I will see if I can find it and post it up

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...